Question about 1997 Chevrolet Cavalier

1 Answer

Front end shutters when breaking

When u go to break for a turn or anything it acts like it has a flat spot and jolts back and forth wen u go to turn the wheel wen stoped it pops

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Like a shudder? might have warped discs on breaks

Posted on Feb 10, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Roaring sound in front end, sounds like driving onvery rough road.


A roar comes from hub bearings pick up the front with a jack n shake the tire back n forth if it has play your bearing is bad

Sep 23, 2015 | Cars & Trucks

1 Answer

My 2003 Chevy Impala keeps making a noise when I crank it up. It sounds like a voltage regulator or something. Also my traction control light keeps coming on and making a rumbling noise when I take off...


Could be a bad electrical connection to your Anit-lock brakes and TC harness. These bend back and forth and break over time. The noise can be anything, but if you have a fuel starvation or back pressure issue, the engine will shutter when you push the accelerator down.

Feb 15, 2011 | 2003 Chevrolet Impala

1 Answer

Jaguar xj6 break light cancels signal


Replace the turn signal switch. Bad contact inside causing a crossing of the circuits. When the turn signal is applied it should open the brake light circuit allowing for just the signal to work. Doesn't sound like the switch is doing it's job.

May 23, 2010 | 1989 Jaguar Vanden Plas

1 Answer

Every time i push on the gas it starts to jolt back and forth and some times it breaks down when im stopped but it always starts right back up


is the car skipping? if so you could have a bad spark plug or plug wire check your plugs the dirty one well be the problem good luck cj

May 14, 2010 | 1993 Oldsmobile Cutlass Supreme

2 Answers

2006 Jeep Grand Cherokee grinding while steering


I'd bet your brake rotors are grooved and need to be resurfaced (or replaced if they are too thin). This also means you should replace the pads too.

Apr 03, 2010 | 2006 Jeep Grand Cherokee

2 Answers

Loud slam & jolt after touching breaks & loud pop in sharp turn


First the obvious, I can't tell by sound descriptions. But it is helpful nonetheless. Have you visually inspected wheels? Removed wheel and looked at brake pads? Calipers sticking? Have they ever been rebuilt? System purged of old brake fluid? Are blazers front wheel drive? or even 4 wd? then front drive system is causing noise when steering. Not front driven? Then I don't have a clue.

Mar 05, 2010 | 1996 Chevrolet Blazer

2 Answers

Toyota townace 1988 - handbrake light comes on when turning right. Whats the source of problem?


I would suspect that the power cable coming from the hand brake to the light on the dash board is lying on the steering column and over the years the insulation has chafed until it will make a circuit in a certain position. The fix is easy once you have found the worn spot. Just wrap it in insulation tape and hold it away from whatever is cauisdng it to chafe with either a cable tie or more insulation tape.

Mar 02, 2010 | 1985 Toyota Passenger

1 Answer

Front end squeaking possible rotor rubbing something.


Have you checked the metal clips that olds the brake pads in the front galiper bracket. They usualy rust, break loose and come in contact whit the disc, creating a squeaking noise. Those should be replace since they are needed for the brakes to work properly

Jun 24, 2009 | 2007 Buick Rendezvous CXL SUV

1 Answer

Car kicks back and forth when idling or the gas is applied


It sounds like you have some broken motor mounts under the hood and one of the main ones that break on those models is the torque strut. When my torque strut was bad in my car the car would jolt when I shifted the gears and it would shimmy when it was idling. I would get your motor mounts checked to see if thats the issue and if its not it may be a motor issue such as a misfire which can couse the motor to backfire and idle rough when its misfiring. I hope this works!!!

Jan 17, 2009 | 1995 Saturn Sl

Not finding what you are looking for?
1997 Chevrolet Cavalier Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...