Question about Cars & Trucks

Open Question

Jeep wrangler door won't open from inside and out check all linkerage

Jeep wrangler door wonn't open from inside and out check all rods but can't find problelm

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

JustJeeps
  • 74 Answers

SOURCE: 98 Jeep Wrangler door handle won't open door

there is a metal bar inside that clips into the handle they come off all the time there is a plastic clip that hold the 2 together it most likely has fallen off and into the bottom of the door you can put it back together easily if clip cannot be found you can buy them at local parts store for a couple bucks..hope this helps

Posted on Nov 21, 2008

motor1258
  • 6674 Answers

SOURCE: 1997 Jeep Wrangler Door Lock Gets Stuck in Cold Weather

Shopping list: Spray can of "White Lithium grease" and a spray can of WD-40 or similar penetrating lubricant, and spray the door latch assy, inside out, with WD-40 first. Even if you have to put window down & aim spray nozzle from top at area of latch, and soak it. Stick the nozzle inside the key slot also, and give it a few squirts. After you let it sit for a minute or 2 start working the lock on door, lock ,unlock, lock, unlock, until you feel it getting easier, now do same with key, until it starts to loosen up. Once you get it working freely, give it a few minutes, and do same with "white lithium grease". That will hopefully protect it from seizing (rusting) up again. Every once in a while when you think of it, give latch another shot of lithium grease. I usually try to do mine before & after winter, or whenever I start to feel it getting a little stiff again. Worst thing is the glass you have to clean if you aim spray too much toward glass, but small price to pay for not having to pull door panel off. If your door panel is easy to get off to allow for better access to back of latch assy, that would definately be better, but that's up to you & your experience with tools. Then you can be sure you got all the related linkages lubed where they need to be.

Posted on Dec 23, 2008

moparownr
  • 667 Answers

SOURCE: The passenger door will not open 1993 Jeep Wrangler

assuming that this jeep has not been wrecked recently, the only way to get that door open is to remove the door panel while the door is closed, at least enough to reach the door latch inside the door, once reached you can operate it and release it to open the door, I will tell you that the likely hood of damage to the door panel will probably occur, I have had this problem before and I had to cut a hole in the panel reach in and open the door, sorry it can't be simpler. if you feel the latch operating and you have recently ran into something, try pull the door handle from inside while pushing the door open

Posted on Mar 24, 2009

  • 6982 Answers

SOURCE: 1998 Jeep wrangler

Remove the inner door panel and check to make sure that the linkage rod that goes between the outer handle and the latch is connected. It's possible that the plastic end clip broke.

Posted on Jul 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My door will not open with the outer latch. Its a 2002 jeep wrangler X with full doors.


I've seen this way too many times...the rod connecting the handle and the actuator has come off. You can take the door panel off and reconnect it - just take a good look, it's very obvious how where it fits in to. If the rod will not stay in the slot on the handle or the actuator the clip is broken - the handle's clip will come with a new lock rod, but the clip on the actuator is integral and you'd have to replace the entire actuator - also very easy.

Check around your door handle for damage - this happens a lot during breakins.

May 10, 2011 | Jeep Wrangler Cars & Trucks

1 Answer

I have a jeep wrangler 1998 model and i can open from the outside but i cant from the inside


Most likely the rod that connects from the inside lever to the latch has come disconnected. There are small plastic clips that hold the rod to the latch, that may have broke. Would require removing the door panel.

Mar 11, 2010 | 1993 Jeep Wrangler

2 Answers

1993 jeep wrangler drivers side door won't open?even from inside


check to make sure your seatbelt is not caught in the latch. if this is the case it may just take a little force.

Oct 27, 2009 | 1993 Jeep Wrangler

1 Answer

1998 Jeep wrangler


Remove the inner door panel and check to make sure that the linkage rod that goes between the outer handle and the latch is connected. It's possible that the plastic end clip broke.

Jul 10, 2009 | 2006 Jeep Wrangler

2 Answers

93 jeep door lock Broken


It might an easy fix...

I had the same problem and it ended up that it only was a metal rod that was unhook from mechanism...

-undo your inside panel by pulling on it
- check the mechanism...

Be careful there is some small plastic pieces that breaks easily after 15 years of life!

hope this helps!

Mar 27, 2009 | 1993 Jeep Wrangler

1 Answer

The passenger door will not open 1993 Jeep Wrangler


assuming that this jeep has not been wrecked recently, the only way to get that door open is to remove the door panel while the door is closed, at least enough to reach the door latch inside the door, once reached you can operate it and release it to open the door, I will tell you that the likely hood of damage to the door panel will probably occur, I have had this problem before and I had to cut a hole in the panel reach in and open the door, sorry it can't be simpler. if you feel the latch operating and you have recently ran into something, try pull the door handle from inside while pushing the door open

Mar 23, 2009 | 1993 Jeep Wrangler

1 Answer

Jeep 1992 yJ Outside Door Handle


ok, the inside panel is cardboard with faux leather. remove the screws holding on the inside handle and the frame of the doorlatch.

there is a plastic joint that connects the two rods that actuate and open the door. the rods are bent at the end to slip into the white plastic joint. this design is stupid and often times that joint can break, or the rods fall out. solution is to reattach them together and wrap mechanics wire or bend the very ends of the rods so they wont come out.

its something i cant really explain, but the design is straight forward. also, keep track of the threads on the rod that connects to the claw that meets the striker on the frame of the jeep. if for any reason its not adjusted properly, it will not latch properly.


Mar 01, 2009 | 1992 Jeep Wrangler

1 Answer

Inside door handle rod on a Jeep Wrangler 1999


You will need to remove the door panel. Most use a special clip to attach it to the lock mechanisim. Look in the bottom of the door to find the clip that fell off. If you can't find it you will have to go to chrysler to get another clip or try a wrecking yard and they will probably just give it to you.

Dec 10, 2008 | 1999 Jeep Wrangler

1 Answer

Lock mechanism in my doors is broke


the rod inside the door has come off this happens often, most of the time its because the srcew holding the inside door handle is loose try tightening it first, if this does't work remove the inside door handle held on with a t15 or t 20 scew and see if the rod has come off at the handle try pulling on the rods to unlock the door then open it, once the door is open remove door panel 2 screws at bottom and just pry up on the soft upper grommets if it a half door reomve door panel and plastic moisture barrier rods connect from the outside lock cylinder to the lock mech and rods also go from the inside lock to the mech one or both of these has come off reconnect them sometime the clips to hold them in place fall down into the bottom of the door if they are not on the rods look there..hope this helps

Aug 03, 2008 | 2002 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

686 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...