Question about Rover 45

Open Question

How do I change a front signal light bulb in a 2000 rover 45

Posted by on

  • john_caldeco
    john_caldeco Feb 10, 2012

    The bulb is in an awkward place and I can't see any access to it. It's the Right side front.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Chevrolet Cavilier turn signal bulb

I know what you mean, it is really tough to get to.  I just had the guy from autozone put it in for me when I bought it.  It got to it quick.

Posted on Nov 08, 2008

Ad
Ajkill
  • 2035 Answers

SOURCE: replace front driver signal light bulb

Depending on whether it is the front or the back turn indicator light will determine on what needs to be done. If it is the front turn indicator light open the hood of the car you may need to take the entire headlight out. The headlight may have screws, take the screws out then the front light will come out from the outside of the vehicle replace the burned out bulb. The bulb should snap right in and then put the headlight back in make sure you put all screws back in from the inside of the hood. Step2 If it is the back turn indicator light, go through the trunk of the vehicle. If there is a panel covering the lights you must unscrew the panel and then replace the burned out light bulb. Some panels can be folded down without removing all of the screws to access the lights. This light may not require for you to pop the entire light out you maybe able to just replace the bulb. After you have replaced it screw the panel back into place. The back light should not require the entire light to be lifted out just a simple bulb replacement. Step3 In replacing either the front or the back indicator light you must gain access to the turn signal housing which is usually in the same case as the headlight or your rear lights. It is very helpful to also get the owners manual out this will tell you exactly what type of bulbs you will need to get to replace the indicator bulb.

Posted on May 29, 2008

  • 12 Answers

SOURCE: replace the front turn signal light bulb

you should have two tongues holding the main headlamp assembly, they are towards the inside of the engine compartement, slide them off upwards and wiggle the assembly and should come off, once off you'll have access to you signal light, hope it helps

Posted on Dec 17, 2008

  • 15 Answers

SOURCE: rover 45 - oil capacity and type

Hi, Go to http://www.mg-rover.org, covers all MG Rover models, they will know exactly and type, etc.

Posted on Jun 02, 2009

  • 202 Answers

SOURCE: how do you change a front signal bulb on a 2004 accord

Front turn signal bulb replacement

1. Remove the inner fender
2. Disconnect the 3p connector from the front turn signal/side marker light.
3. Turn the bub socket ( 45 degree ), counterclockwise to remove the bulb.
4. Install a new bulb in the reverse order of removal.

Posted on Apr 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change front turn signal bulbs


This may help. It shows how to remove the light assembly to gain access to all the bulbs on the front.

Feb 25, 2015 | 2000 Buick Century

1 Answer

2000 landrover disc. rear signals not working but front signals are can anyone please help


check the rear lighting wire loom from rear of light clusters ,trace the earth wire to the body/chassis connection to ensure a good earth , check for power to the indicater lamp , the bulb holders may be the problem , this is a problem that requires patience as can be hard to trace

May 08, 2014 | 2000 Land Rover Discovery

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

1 Answer

How do you change a front signal bulb on a 2004 accord


Front turn signal bulb replacement

1. Remove the inner fender
2. Disconnect the 3p connector from the front turn signal/side marker light.
3. Turn the bub socket ( 45 degree ), counterclockwise to remove the bulb.
4. Install a new bulb in the reverse order of removal.

Apr 12, 2010 | 2004 Honda Accord

2 Answers

What could cause my right front turn signal to not work some of the time. The bulb was checked and even replaced but did not solve the problem. Each time the car is turned off, the signal will work for a...


Some of th intermitent problems with lights can be traced to bad ground connection since flasher bulbs draw quite a bit of current. Some cars use the car bodywork as the ground connection. If the rear lamp flashes faster than normal when the front one does not you have a bad connection. Check the bulb holder and the ground connection.

Nov 24, 2009 | 2003 Land Rover Range Rover

3 Answers

Right turn signal won't work after replacing bulb 2004Range Rover


I've had the same problem. It is the actual socket that the bulb plugs into - it is defective. Try removing the light unit and turning the bulb a bit (with the indicator on) and you'll see that it will slow down once it makes contact. Very annoying!!!! RR should have had that fixed ages ago. May need new socket.

Apr 03, 2009 | 2004 Land Rover Range Rover

1 Answer

Left Signal light isnt blinking on my 2000 300M Chrysler


you need to replace the rear driver side light bulb. it will fix the problem.

Feb 27, 2009 | 2000 Dodge Ram 1500 Truck

1 Answer

2000 Accord turn signal problem


either the front or the rear turn signal bulb is blown, that is why the flash frequency is high. replace the bulb and the problem will be solved. best to replace both the front and rear turn signal bulbs. good luck.

Aug 29, 2008 | 2000 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rover Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Rob
Rob

Level 2 Expert

62 Answers

Are you a Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...