Question about Hyundai Motor 2002 Elantra

1 Answer

Cruise control and autostart

The cruise control worked fine until last week. The light on the dash comes on but when the lever is pushed to set it, it doesn't engage.
The autostart worked fine also but now it sounds like in engages but when you take out the key the motor stops.
its a 2002 5 speed manual

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 344 Answers

It sound to me like the transponder loop around the ignition switchor "key in the box" needs to be repositioned or the key sense wire circuit

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i set the cruise control on my 1994 mercedes c220 elegance automatic


Cruise Control
Any given speed above approximately 22 mph (35 km/h) can be maintained with the cruise control by operating the lever.
-see photo

  1. Accelerate and set: Lift lever briefly to set speed. Hold lever up to accelerate.
  2. Decelerate and set:
    Depress lever briefly to set speed. Hold lever down to decelerate.
    Normally the vehicle is accelerated to the desired speed with the accelerator. Speed is set by briefly pushing
    the lever to position 1 or 2. The accelerator can be released. The speed can be increased (e.g. for passing)
    by using the accelerator. As soon as the accelerator is released, the previously set speed will be resumed automatically. If a set speed is to be increased or decreased slightly, e.g. to adapt to the traffic flow, hold lever in position 1 or 2 until the desired speed is reached, or briefly tip the control lever in the appropriate direction for increases or decreases in 0.6 mph (1 km/h) increments. When the lever is released, the newly set speed remains.
  3. Canceling
To cancel the cruise control, briefly push lever to position 3.
When you step on the brake or the vehicle speed drops below approx. 22 rnph (35 km/h), for example when driving upgrade, the cruise control will be canceled.
4. Resume
If the lever is briefly pushed to position 4 when driving at a speed exceeding approx. 22 mph (35 km/h), the vehicle resumes the speed which was set prior to the cancellation of the cruise control. The last memorized speed is canceled when the key in the steering lock is turned to position 1 or 0.
Note:
If the engine does not brake the vehicle sufficiently while driving on a downgrade, the speed you set on the cruise control may be exceeded and you may have to step on the brake pedal to slow down.
As soon as the grade eases, the cruise controlled speed will again be maintained as long as the brakes were not previously applied, or the lever may be used to resume the previously set speed if the brakes were applied.

set-cruise-control-1994-mercedes-c220-sufrpujyrsap3pvz3w2boz5j-3-0.jpg
http://www.benzworld.org/forums/attachments/w202-c36-c43/153145d1197313761-pdf-owners-manual-w202-1995-2000-1999-c280_owners_manual.pdf

Feb 14, 2015 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

Etc light on 2009 Chrysler 300


Whenever this warning or any other stays on in the dash it is indicating that the systems control module has detected a fault, it then disables the system as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Oct 04, 2012 | 2009 Chrysler 300

2 Answers

The cruise control switch will not engage or set when pushing set button, but the green cruise light is on on the dash.


Check your fuse panels both inside, and outside the vehicle, as well as the connections to the cruise control.

Mar 29, 2011 | Nissan Frontier Cars & Trucks

2 Answers

2004 ford taurus cruise control not working even though the light on the dash comes on when the switch is engaged


The cruise control cable has probably fallen off the throttle lever under the hood. The retainer vibrates loose over time. Either replace the cable or find a way to keep the cable attached to the throttle lever.

Nov 15, 2010 | 2004 Ford Taurus

1 Answer

2004 ford taurus cruise control not working even though the light on the dash comes on when the switch is engaged


There are 2 connections to the throttle lever on the throttle body under the hood. One is for the gas pedal and the other is for the cruise control. The connection for the cruise control is the lower connection. The cable has a very weak retainer system. The retainer clips wear until the cable breaks away from the throttle. To get at this area, you must remove the plastic shield that is held on with 2 push pins. Just pry the push pins up and out of their holes and the cover comes loose. You must either replace the cruise control cable (~$35.00) or reattach the cable end and use a wire tie to keep it from coming off again.

Jan 18, 2010 | 2004 Ford Taurus

1 Answer

My cruise control has stopped working


sound like its the cruise control unit not working.if lights is on and its not working.its a dealership fix.

Jul 21, 2009 | 1992 Toyota Camry V6

1 Answer

2004 Hyundai Elantra.......Cruise control will not engage


make sure the cruise control cable to the throttle isn't too loose, if it is ok, check your brake switch. if it is sending the signal the brake is on it will not allow cruise to work and will do same thing as described about the set light.

May 08, 2009 | 2004 Hyundai Elantra

1 Answer

2003 Yukon, cruise control no longer works


check your linkage up by the throttle if thats good check your relays and fuses

Jan 28, 2009 | 2003 GMC Yukon

1 Answer

Cruise Control Problems


Possibly a fuse if you haven't checked, My MAX a/c switch wouldn't light up or work so I looked at the fuses and the wrong fuse was in the blower and cig lighter so I changed them and the a/c is working perfectly so check to make sure the fuses are the correct ones or they possibly wont work!!!

Aug 31, 2008 | 1995 Nissan Pathfinder

Not finding what you are looking for?
Hyundai Motor 2002 Elantra Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...