Question about 2002 Jeep Grand Cherokee

1 Answer

My signal light, and brake light works when they want to. My emergency flashers don't work and my trunk want open

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The error with the lights sounds like a problem with the wiring or the relay being busted - check the relay up front, if that isn't the problem, give the wiring a shot.
The trunk not opening might very well be a spring not working for the release of the lock mechanism.

Posted on Feb 10, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 tacoma flashers don't work but turn sig do work!


The hazard switch gets power from the horn fuse which is hot all the time, and from the turn signal fuse which is hot when the key switch is on. The turn signal switch gets power from the hazard switch and both use the same flasher.
So if the turn signals work but the hazard switch does not power the lights, and both fuses have power, I would say the problem is inside the hazard switch.

Feb 19, 2013 | Cars & Trucks

3 Answers

1994 Chevy C1500 truck. No rear brake lights


Most likely this is a brake light switch issue. Replace switch.

If your emergency flashers don't work, all flasher bulbs are fine, but flashing too fast, then check and replace Hazard light switch.

Oct 29, 2012 | 1994 Chevrolet C1500

1 Answer

Brake lights and turn signal don't work???


turn on the emergency flashers(e-flashers)if they work check the bulbs at the same time.if this is good then check the fuses.you may have a problem with the turn signal flasher needing replacing.this is a different flasher than that of the e-flasher,looks the same but a different flasher.usually located on or around the fuse panel under the dash.the brake light problem could be a misadjusted switch or a bad switch.the switch is at the base of the brake pedal and has two wires to it.one wire will have power all the time and the other wire will only have power on it when the brake pedal is pushed.if not then the switch will need replacing.check for broken wires at the switch as these sometimes break causing a problem.

Feb 08, 2012 | 1996 Pontiac Sunfire

1 Answer

Signal light and emergency flashers don't work


Check the relays and then check the wires... If its a relay you will need to replace it and of its a wire problem either fix the wires or get a new wiring harness

Dec 23, 2011 | 1997 Mercury Grand Marquis

1 Answer

My turning signal don't work but the flashers do work. I have changed all fuses and they still don't work.


since you know where the fuses are, you also know where the flashers are. the flashers are the same part so unplug the one for the emergency flasher and put it into the socket for the turn signals and vice versa. if the signals now work but not the emergency flasher you know to get a new flasher unit at any parts store. the flasher units are cubes about an inch on each side plugged into the fuse panel.

Jun 27, 2011 | 1995 Chevrolet Caprice Classic

2 Answers

Need to replace the turn signal flasher. the dash lites & tail lights don't work.


It is located behind the fuse block on the driver's side. When you open the drivers door you can plainly see the fuse block. (marked "FUSES") Flasher is behind that. You have to get to it from under the dash. Take out panels under steering wheel. If you get your head down by the brake pedal you can see it.
When someone changed theirs, they took out the little bracket that holds it in and relocated it to a lower place - they clipped the flasher bracket onto the little access door closest to the emergency brake (on the panel that you have to take out). Luckily the wires were long enough to enable this, so if you have to change it again, it's a lot easier.

May 10, 2011 | 1995 Pontiac Grand Am

1 Answer

I have an interesting problem with my 01 Passat. The turn signals are not working, however the hazards are working. Could this be the hazard relay? The high beam on the right side is not working, and today...


The turn signals use one flasher and emergency uses another one. You can exchange the two (usually) for a quick check. The bad one will move to the other system when swapped, emergency flashers now don't work but the turn signals do. If this is the case go get a new flasher and replace it.

Mar 06, 2009 | 1998 Volkswagen Passat

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...