Question about 2003 Mazda Protege

Open Question

Mazda protege 2.0L no acelera en marcha

2003 mazda protege 2.0L, the engine starts but when I start (run) does not accelerate (not advance)

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2001 mazda protege keeps stalling

my 2001 mazda protege starts hard, idles low and high at various times (never normal) and it acts as though its going to stall at all times. sparks and wires are changed no help, changed air filter no help. any idea on what to do?

Posted on Nov 26, 2009

Ad
  • 1 Answer

SOURCE: Blown main fuse on 2003 mazda protege 5.

There are two bolts on the side of the fuse itself. Under the fuse box on each side. Unbolt those and it will come out.

Posted on Dec 23, 2008

  • 1 Answer

SOURCE: 2002 Mazda Protege acceleration problem

I had the same problem and found that the air admission tube was badly cracked.

Since this let air enter the engine downstream of the mass airflow sensor it is not measured so the engine ECU don't send the proper amount of fuel to provide the right air/fuel mixture. At higher RPM, the vacuum in the tube is enough to close the crack and hide the problem.

I temporarly repaired it with duct tape until I get the part.

Stephane

4cc37fa.jpg

Posted on May 27, 2009

alicantecoli
  • 22219 Answers

SOURCE: how to adjust a hydraulic clutch mazda protege 01

removing a gearbox is not a thumbs up job for the average person,their is no adjustment ,if its slipping then renew the clutch ,most hydraulic systems are self adjusting .Trust me even after 40yrs being a mechanic i still hate doing clutches

Posted on Jan 12, 2010

  • 2 Answers

SOURCE: For 2003 Mazda Protege ES model 2.0L 4cyl engine;

Check the air inlet boot going from the air filter to the intake for rips or holes. If rips exist, this would allow air to bypass the filter and mass air flow sensor and will lead to a check engine light appearing. The code would read "too lean, bank 1." If this problem is allowed to continue for long periods of time, the EGR ports will have to be cleaned out and maybe even the intake.

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a mazda protege 1.6 year 2000 the egr valve is open at all time i test a close one but the engine start to vibraye to much


Make sure the EGR ports aren't clogged with carbon. It can completely clog ports. EGR shouldn't be open at IDLE, but it will open upon accelerating.

-Scott

Feb 19, 2015 | 2000 Mazda Protege

1 Answer

Mazda Protege 2001 1,6/codico P1345


TENGO FALLA CUANDO VOY EN MARCHA Y SE DETIENE CUANDO ESTOY EN EL SEMAFORO EMPIEZA A FALLAR Y SE APAGA EL MOTOR

Jan 01, 2013 | Cars & Trucks

1 Answer

01 mazda will start but then shuts off


I have seen this problem and it was the air intake hose of the engine was cracked and allowing excessive unmetered air to enter the engine when you accelerate (causes the engine to run very lean and stall out) due to engine lift, the crack is hard to see and will be on the bottom of the hose.

Feb 08, 2012 | 2001 Mazda Protege

1 Answer

For 2003 Mazda Protege ES model 2.0L 4cyl engine; engine running rough and ''shaking at idle'' when stopped on road for traffic light for example. Also becomming hard to start. Someone mentioned a ''cold...


Check the air inlet boot going from the air filter to the intake for rips or holes. If rips exist, this would allow air to bypass the filter and mass air flow sensor and will lead to a check engine light appearing. The code would read "too lean, bank 1." If this problem is allowed to continue for long periods of time, the EGR ports will have to be cleaned out and maybe even the intake.

Mar 05, 2010 | 2003 Mazda Protege

2 Answers

I have a mazda protege 2003 and my car stinks like rotten eggs when i put on the gas and on top of that, my engine light is blinking and my car shakes when i stop at a red light!


i have a 2003 mazda protege. this is the third time my check engine light has come on. the first time the car started to shake when i stopped at a light and the check engine light came on. i had a readout done and it said misfire. i took it to a garage and they changed my spark plugs and wires. 2 weeks later it came on again and my car started to shake whenever i stopped. readout said misfire. they fixed the coils. it has been 2 weeks since then and my car started shaking again whenever i stop and the light came on. what could possibly be wrong with it?

Feb 06, 2010 | 2003 Mazda Protege

Not finding what you are looking for?
2003 Mazda Protege Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...