Question about 1994 Jeep Wrangler

1 Answer

94 Jeep Wrangler Seat Belt Installation

I bought a 94 Jeep Wrangler that did not have a rear seat. I have since purchased a seat and seat belts. The directions with the seat belts were not very helpful. Does anyone have an illustration as to where everything will mount or better instructions?

Posted by on

  • Anonymous Mar 19, 2014

    no light in cluster

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Your jeep should have all the holes and thread nuts already installed. pull up the carpet and locate them. the two close to the center are for seat belts as are the two outside of them. the four holes that form a large square/rectangular area are for the seat. if your seat is fold and tumble type, holes on the left wheel well are for the locking mechanism. i just pulled mine out and filled the thread holes with new bolts to keep out the water and dirt. yours may have screws or plugs in them. this install is for factory type only. mike

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Jeep Wranglers driver seat belt will not work.


DO NOT TRY TO FIX IT....an unsafe belt is like a gun with the safety off.please replace it asap.its an easy job to do,just remove the trim and the bolts are in front of you....

Jul 09, 2010 | 1995 Jeep Wrangler

1 Answer

Where is the jack located in a 1999 Jeep wrangler


The 99 TJ Wrangler has the Jack strapped to the floor board under the passenger seat, tilt the passenger seat forward toward the glove box like you would if your were getting into the back seat and then you should see it strapped to the floor directly under the seat.......My guess is that if the Jack is not there then it's probably missing if you purchased the Jeep used from someone else.

May 14, 2010 | 1999 Jeep Wrangler

1 Answer

I need diagram for serpentine belt installation on 1999 jeep wrangler.


Check HERE for few engine sizes:
- 1999 JEEP WRANGLER - L4 2.5L 150ci GAS FI N P
- 1999 JEEP WRANGLER - L6 4.0L 242ci GAS FI N S

Hope this help (remember comment and rated this post).

Apr 09, 2010 | 1999 Jeep Wrangler

2 Answers

Rear middle seat belt in 2005 jeep grand cherokee will not work


take it to your dealer and tell them the problem they should be able to fix/relpace the seat belt

Aug 11, 2009 | 2005 Jeep Grand Cherokee

2 Answers

2005 Jeep Grand Cherokee LTD Rear Seat belt Stuck


anyone have answer for this problem??? i have 05 grand cherokee with same issue.

Aug 10, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Seat belt is locked.


open its cover to releas it
it may have grime or a coin in it

Jul 20, 2009 | 2005 Jeep Grand Cherokee

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

Adding a third seat belt/2008 Wrangler


Issue is not voiding the warranty so much as the safety issues. If you have an accident, Jeep will disavow any liability for any injuries.

While I wish I could also put 3 in back seat of my Wrangler, with carseats for grandkids, no way to safely go 3 across. Strongest selling point for the 4-door model.

May 23, 2009 | 2008 Jeep Wrangler

3 Answers

3rd seat belt in a jeep wrangler


Bolting it in a third row seat? that'd be fairly easy...just need something solid to anchor it to (like a thick piece of metal) on the underside to put the bolt through. do the same with seat [lap] belts and that should solve any law issues (actually some states i believe don't "require" rear seat passengers to be belted in, but I'd strongly suggest it for the kids safety!)...my big question is where are you finding enough room for a 3rd row seat? wranglers aren't exactly loaded on space...

as for torque...wrangler seats are fully removable (makes it easy to wash mud and stuff out) so as long as the bolts tighten down (air gun preferably, but you can arm twist em if need be) you'll be fine, just make sure everything is as secure/sturdy as the factory seats

Dec 30, 2008 | 1994 Jeep Wrangler

1 Answer

Seat belt indicator


look under the drivers seat there is a plug that may be unplugged or broken this is what tells the light to stay on plug it in or try unplugging it and see what happens, on some of the 200 and up models the seat belt light may have some affect on airbags working properly, I have not found this to be the case on 97 model.

Aug 22, 2008 | 2002 Jeep Wrangler

Not finding what you are looking for?
1994 Jeep Wrangler Logo

Related Topics:

857 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...