Question about 2006 Chevrolet Cobalt

1 Answer

Suspension problem in chev cobalt 2006

When the car is driving it makes a vibration on the front left wheel

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 76,630 Answers

Have the tire checked for a separated internal steel cord, also for any signs of a bent wheel. Most tire shops will do this inspection for free.

Posted on Feb 10, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2006 Chev Cobalt oil filter replacement

i have a 2006 chevy cobalt LT..and i just replaced my oil filter today!!! after several hours of looking i finally looked on the front side of the transmission block.to the left just below the air intake system is a hard heat resistant plastic black bolt topper.it is 1 1/4" in size..i bought a 1 1/2" size and a 36mm size socket torque wrench..both didnt work..1 1/2 was way too big, the 36mm was just slightly too big..took them back, replaced for the 1 1/4" inch socket and voila!!! is was rather difficult..you will need an extender and some good torquing to do to pop it..but once you do it will pop fine..oh, and you will need a 1/2" drive socket wrench.but the 1 1/4"inch socket..pop it onto a 1/2" drive socket wrench with the extender and you are good to go!!

Posted on Jun 10, 2008

brandyspoile
  • 61 Answers

SOURCE: how to remove inner window crank on 2006 chev cobalt 2 dr

the handle part of the crank is held on by a small ring, you will need a small flat head screw driver- i used a butter knife, as it works better- push the door panel back just enough you can see behind the round part of the handle, you should be able to see the foot of the clip, push it off, make sure you don't do this in the grass, the ring will roll when it falls off. **please note this is a flat ring and only about the diameter of your little finger**

Posted on Nov 25, 2008

daves944
  • 1050 Answers

SOURCE: Noises problem 2006 Chevy Cobalt 4 cyl Front Wheel Drive Automati

Wow, sounds like a good one, my only suggestion would be, try changing or machining the brake rotor and double checking to make sure all the caliper hardware is torqued up tight. Possibly a tire? Try switching side to side.

Posted on Mar 12, 2009

  • 79 Answers

SOURCE: Vibration and noise from front end while driving

Jack up the front end and put stands under it and block rear wheels. Look at axle boots and see if they are cracked. Try turning wheel back and forth sharply and see if you can hear any clicking. Problem could be outer axle joints. If the boots are cracked or you hear a clicking noise you will have to replace the axle. The axle and boot come as a complete unit. Please let me know what you find out.

Posted on Apr 15, 2009

countrysi248
  • 443 Answers

SOURCE: grinding noise front end

its either your front brake pads or your CV joint is going bad .. Jerry

Posted on May 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Any ideas why a 2003 chevy trailblazer may vibrate in the front but stops when you turn left


Does the vehicle make any noises while driving? If there is a "growling or roaring " noise associated with the vibration, check the right front hub bearing. If there are no noises and only vibration, check the right front upper ball joint and control arm bushings. The Trailblazer's upper ball joint and control arm bushings become worn and cause the tire and wheel assembly to shimmy while driving. The vibration stops when turning left because of weight transfer to the right side which keeps the wheel steady for a moment. Also, check the tire for irregular wear.

Mar 05, 2015 | 2003 Chevrolet TrailBlazer

1 Answer

Vibration through steering when turning left


check your tyres sounds like buldging in the rubber replace immediately

Feb 11, 2015 | Cars & Trucks

1 Answer

Changing front axle assembly or wheel hub or both? Either way, need torque specs for all bolts.


you've got a bad axle shaft in the front and possibly a bad bearing in the hub. 4/wheel drive makes the front axle actually work. Theys no real pressure on these shafts when in 2/wheel drive.

Feb 01, 2013 | 2002 Chevrolet Silverado 1500

1 Answer

I have a violent vibration when accelerating especially up a hill or over 60 MPH. The vibration goes immediately away when I let off of the gas. My mechanic has replaced the following to no avail: L...


Rev the engine while out of gear , if vibration check units driven by fan belts. if no vibration and is front wheel drive, check joints on both drive shafts, if rear wheel drive check front and rear tail shaft u / joints, check wheel balance or out of round tyre .

Jun 14, 2017 | 2002 Kia Sedona

1 Answer

Vibration/Humming/Grinding noises when stopping or turning left.


when turning left vehicle distributes weight to right front wheel bearing causing load. since u describe a noise in right front while driving straight i would suspect failed right front wheel bearing. see if your noise changes/goes away while turning right that should tell u 4 sure

Nov 15, 2009 | 2004 Chrysler Town & Country

2 Answers

Vibration


It sounds like a possible bad front wheel bearing they will make like a humming or growling noise.The pull could be air pressure a little lower in the right front tire than the left front check the air in all tires and if pull is still there take the left front put it on the right front and put the right front tire on the left front.Sometimes tires get what they call radial pull and that will fix it or make it go the other way if it goes the other way either get new tires or put the back tires on the front of the vehicle and put the front tires on the back.

Feb 22, 2009 | 1992 BMW 7 Series

1 Answer

Front End noise and vibration


Check the U-joints and axle baerings. But its most likely because the truck is in four wheel drive.

Aug 16, 2008 | 2002 Ford F350 Super Duty DRW Reg. Cab

Not finding what you are looking for?
2006 Chevrolet Cobalt Logo

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...