Question about 2001 Ford Explorer Sport
Stumbles during acceleration
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
it in the tank so your gonna either gonna have to drain the tank and lower it to the ground,it shouldn't take more than 30 minutes.make sure you put the seal back in right,so it won't leak,it aint very hard.
Posted on Jul 12, 2009
Go to this site pick owner guide from left task bar and get the owners manual. Your fuse info will start on page 162
Posted on Mar 19, 2009
SOURCE: 2001 Ford Explorer Sport
Common problem on 2001 Ford Explores. The reason why your door handle doesn't unlock the door(can't be unlocked by remote either)is due to a broken spring located on the backside of the door handel INSIDE the door. True that your one(or two) of your small exterior springs on your door handle are broken(will cause your handle to flap) but this IS NOT YOUR PROBLEM. The door locks will work if there is a bit of tension holding the handle bracket up. I know it's hard to explain without pics. but here's the ONLY WAY TO FIX THIS. It's not that hard.......... Remove the door panel, only a few screws and a few more holding trim around exit handle then, pull out "snap in" clips on bottom. With a flashlight you'll see back side of door handle. To get to that area you'll have to remove one bolt holding a window frame. Do that(with window in up position) then slide down rail, out of your way. Now, get back to handle. With your light aimed at the backside of handle left slowly the door handle as normal, and you'll realize(while looking at the mechanism) that tension(pulling down of bracket) needs to occur in order for locks(manual and remote)to work properly. Trust me.....you'll figure it out. Once you do, get a spring(pen spring, 30 cent hardware store spring, any small spring!) and hook one end to bracket and the other end to ANYTHING(OUT OF THE WAY) below the door handle thus, causing SLIGHT tension. Try your locks...THEY WILL WORK! YEAH! Replace that one window frame bolt(try your window...just the make sure), replace door panel and your done. TOTAL COST: 30 cents or FREE(if you have a small spring) Ford dealers will charge $150 to $285! Yikes!
Posted on Jun 14, 2009
Gather the necessary tools needed such as wrenches, sockets, screwdriver and pliers.
Place the vehicle on ramps or jack up the front and support with jack stands. It is very important to block the rear wheels to keep the car stationary during this procedure. Never work under a vehicle not supported properly
Make sure ignition is OFF and the remove the negative (ground) battery cable from the battery.
Note the location of all wires before removal to make for easier connection.
Remove the large starter cable going to the battery at the starter location.
Remove any other wires attached to the solenoid.
Remove the starter attaching bolts (usually there are two or three).
Remove any supporting brackets that holds the starter.
Drop the starter down away from the car. On some cars you may have to turn the wheels to one side, remove the idler arm, remove or loosen transmission oil cooler lines, exhaust pipes, or ground straps to give you enough clearance to get the starter motor away from the car.
Install the new starter in the reverse order of removal.
Reconnect battery cables and other wires to solenoid.
Place old starter in the new starter box for proper core return.
Posted on Sep 20, 2009
How to find the Security Keyless Keypad Code on the 1995-2001 Ford
Explorer or Mountaineer and how to use the Keypad functions. The factory
code is also printed on a label which is installed on the Remote
Anti-theft Personality (RAP) Module. This is the module that controls
the keyless entry system. It is
located in the left rear quarter behind the removable panel (see photo).
You will need to turn the two thumb screws counter clockwise and take
the plastic panel off to be able to see the unit. A flashlight may be
helpful in seeing the code. You are looking for the module and the 5
digit code on it like the one shown below.
Now that you’ve got the code I’ll tell you how to use the Keyless entry and set-up your own code.Make sure when pressing the controls on the keyless entry keypad you press the middle of the buttons to ensure good contact with the controls.
Check this for Programing the Keypad.
Hope this help (remember rated this comment).
Posted on Mar 29, 2010
Tips for a great answer:
Jan 10, 2016 | 2001 Ford Explorer Sport
Jul 04, 2012 | 2001 Ford Explorer Sport
Jul 04, 2012 | 2001 Ford Explorer Sport Trac
Dec 29, 2011 | 2001 Ford Explorer Sport
Jul 26, 2010 | 2001 Ford Explorer Sport Trac
Dec 15, 2009 | 2001 Ford Explorer Sport
Dec 15, 2009 | 2001 Ford Explorer Sport
May 15, 2009 | 1997 Ford Expedition
Apr 12, 2009 | 1997 Ford Expedition
343 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: