Question about 2007 Volkswagen Jetta 2.5 Sedan

1 Answer

Why is there a window wiper signal above the mileage display everytime

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Volkswagen Master
  • 5,332 Answers

That would be the low washer fluid light. If the washer fluid is full than the sensor in the washer bottle may be bad.

Posted on Feb 10, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is it my 2008 chevy uplander rear wiper motor/blade moves some and stops. I let van set 5-10 minutes with key off. Turn on key. Wiper motor/blade moves a few degrees and then stops again. Why?


Can you move the wiper by hand ? Which does your vehicle have ?
WDA/Z88 The rear wiper is controlled based on an input from the rear wiper/washer portion of the multifunction switch. When closed, the wiper ON and wiper DELAY switches provide a unique voltage signal to the rear window wiper motor indicating the desired speed. Each switch has a unique resistor that drops the voltage to a specified value which is interpreted by the rear window wiper motor as ON or DELAY. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
W49 The rear wiper is controlled based on an input from the rear wiper/washer switch. When closed, the wiper ON switch provides a voltage signal to the rear window wiper motor indicating rear wiper operation is requested. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
Do you know how to do electrical testing ?
WDA/Z88
  1. Ignition OFF, disconnect the harness connector X1 at the multifunction switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 4 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the multifunction switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, test for B+ between the signal circuit terminal D and ground.
  12. ?‡'
    If less than the specified value, test the signal circuit for an open/high resistance. If the circuit tests normal, test or replace the multifunction switch.

  13. Rear wiper switch in the DELAY position, test for B+ between the signal circuit terminal D and ground.
  14. ?‡'
    If less than the specified value, test or replace the multifunction switch.

  15. If all circuits test normal, test or replace the rear window wiper motor.
W49
  1. Ignition OFF, disconnect the harness connector at the rear wiper switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 6 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the rear wiper switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, verify a test lamp illuminates between the signal circuit terminal D and ground.
  12. ?‡'
    If the test lamp does not illuminate, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the I/P switch assembly.

  13. If all circuits test normal, test or replace the rear window wiper motor.
Component Testing

Do you know how

Jun 09, 2016 | 2008 Chevrolet Chevrolet Uplander LS

1 Answer

Fuse blows everytime I attempt to use the washer fluid.


really?! the water pump?! the water pump has nothing to do with your wipers it is part of the COOLING system. as for your issue...it could be a short in the wiper/signal arm in the steering column, or it could be the motor in your washer fluid bottle. the motor is what pushes the fluid through to your windshield and if its gone bad it will blow your fuses as well. i would start with the washer fluid reservoir motor and go from there

May 25, 2013 | 2002 Chevrolet Silverado 2500HD

2 Answers

2004 gmc envoy window won't go up rear wiper obstruction


I know this question is old, but I am responding so others with the same problem can see. I wired the Rear Window Motor Park Signal wire and the Rear Window Motor Speed Signal wire together and it completely bypassed the rear wiper motor. Now the window goes up and down. This doesn't fix the rear wiper motor, but you will be able to have access to it now that the window is out of the way

I made and album to show.

http://imgur.com/a/q3vww

Jun 30, 2012 | 2004 GMC Envoy

1 Answer

Cranks strong, wont start


could possibly be a crank sensor, not sending a signal to allow any power to the ignition

Feb 05, 2012 | Cars & Trucks

1 Answer

I have a 2000 Pontiac Bonneville. Everytime I hit the brake pedal my wipers go on. What is the cause of this, and what is its fix?


There's a short, I would first inspect the wiper, turn signal switch. When you find the cause, you'll find the fix.

Dec 06, 2010 | Pontiac Bonneville Cars & Trucks

1 Answer

On a 2002 dodge ram 1500 truck the brake lights and the turn signals and winshield wipers dont work the only brake light that works is above the cab. and the turn signal flashes on the dash like they are...


I suspect a bad multi function switch located in the left hand side of the steering column. This switch controls your high/low beams/wiper delay/windshield washer/turn signals and hazards.

Dec 31, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Signal light and Windshield-Washer Pump


The wipers & turn signals are all in one unit, called a combo switch. It sounds like there is a short in switch which means you will have to replace the whole thing.

May 15, 2009 | 1991 Honda Accord

Not finding what you are looking for?
2007 Volkswagen Jetta 2.5 Sedan Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...