Question about 2003 Kia Sedona

Open Question

2008 kia sedona crankshaft

Check engine light on. Code P0016 Definition Crankshaft Position Camshaft Position Correlation-Bank 1 Sensor A

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 245 Answers

SOURCE: i think i need to change the crankshaft position sensor.

yes the crankshaft position sensor can cause all these problems at once. they are fairly simple to change and not a really expensive part if you want to check it though you can unplug it and hook a multimeter to it and check ohms as someone cranks the engine. should see a square wave as in 0 ohs to infinity ohms and repeat.

Posted on May 20, 2009

  • 1071 Answers

SOURCE: How do I replace the timing belt and the crankshaft sensor ?

if you have never done one take it to a shop because if you have the timing off a little you take a chance of bending valves then you would need a new head

Posted on Jul 23, 2009

  • 36 Answers

SOURCE: where is crankshaft sensor on 99 kia sportage?

The crankshaft pos. sensor is located on the left "driver" side of the engine on the bellhousing and is retained by a single 10mm bolt.The sensor may be tight,be sure to twist as you pull so that it doesnt break off in the bottom end.

Posted on Jul 26, 2009

  • 87 Answers

SOURCE: Crankshaft position sensor replacement on 2005 Kia Sedona

the crankshaft position sensor for that car is located on top of transmission housing close to engine block.

Posted on Jan 26, 2010

  • 67 Answers

SOURCE: 2005 Kia Sedona, Trouble Code P0320. Everything I

This is a common problem usually related to the crankshaft position sensor. Before you replace it, disconnect the electrical connector to the CPS sensor and clean it with electrical contact spray and add a dab of dielectrical grease. If the problem continues, replace the CPS sensor. It is easy to replace and is not very expensive. It just bolts to the engine block with one or two bolts. I believe the CPS sensor on the Sedona is behind the timing cover on the front of the engine.

Posted on Feb 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Camshaft sensor cadillac srx


DTC P0016: Crankshaft Position (CKP) - Intake Camshaft Position (CMP) Correlation Bank 1
DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1

• An actuator that is in the full advance or retard position can cause this DTC to set.
• The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).
• Observing the desired and actual camshaft angle parameters, with a scan tool before a DTC sets, may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.

Now do you want to change a sensor an have it not fix the problem .

May 09, 2017 | Cadillac Cars & Trucks

1 Answer

My 2008 GMC AcadiaSLT2 that is having all sorts of electrical issues. ServiceStabilitracLight on,Traction Control off light, Oil pressure low stop engine. Throws codes P0017,P0016,P0102,P0113,P0700.


DTC P0016: Crankshaft Position (CKP) - Intake Camshaft Position (CMP) Correlation Bank 1

DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1
A camshaft actuator stuck in the full actuation position may cause the engine to crank but not start.
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the park position, and the locking pin retains the CMP actuator sprocket to the camshaft. The park position for the CMP actuator and camshaft is 8.5 degrees before top dead center (BTDC), which is equal to 17 crankshaft degrees BTDC. The engine control module (ECM) can only command the CMP actuator to retard the valve timing from the park position, or advance the valve timing back to the park position. The total range of valve timing authority is approximately 20 degrees of camshaft rotation, which is equal to 40 degrees of crankshaft rotation.
Problems with this will cause the PCM to disable traction control and Stabilitrac .How many miles on your vehicle ?
Chevy Colorado P0017 Case Study Part 1 GM is a GM , Chevy , GMC , Buick , Cadillac etc.....

Jan 15, 2017 | 2008 GMC Acadia SLT-2

1 Answer

P0016 and P0017 check engine pop up after i run for 10 to 15 miles?


the common causes for code P0017 are as follows:
  • A faulty cam or crank sensor
  • The cam or crank circuit is open or shorted
  • The timing belt/chain is out of time
  • The cam or crank tone ring is slipped/broken
  • A problem in the VVT system P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor) God Bless! Hope this helps you.

Mar 08, 2016 | Cars & Trucks

2 Answers

My truck sonoma gmc 2001 dont past the emission test


Definition of Diagnostic Trouble Code P1345 Audi: Ignition Coil Power Output Stage 3 Short to Ground BMW: Misfire Cylinder 2 with Fuel Cut-Off Buick: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Cadillac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Chevrolet: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Ford: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) GMC: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Isuzu: Crankshaft Position - Camshaft Position Correlation Kia: No SGC Signal (1.6L) Lexus: Variable Valve Timing / CMP Sensor Range / Performance Lincoln: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Mazda: Cylinder Discrimination Signal (from CMP sensor) Mercury: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Oldsmobile: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Pontiac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Saturn: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Toyota: Variable Valve Timing / CMP Sensor Range / Performance Volkswagen: Ignition Coil Power Output Stage 3 Short to Ground

Jul 19, 2015 | GMC Cars & Trucks

2 Answers

What is code p0016


Crankshaft Position Camshaft position Correlation Bank 1 Sensor 'a'

Apr 14, 2015 | Cars & Trucks

1 Answer

2005 f150 5.4 code p0016


EOBD II Error Code: P0016
Description:
Crankshaft Position (CKP)/Camshaft Position (CMP), Bank 1 Sensor A - Correlation
Indication:
Malfunction Indicator Lamp (MIL) ON.
Solutions:
Wiring.
Crankshaft position (CKP) sensor.
Camshaft position (CMP) sensor.
Mechanical fault.
Timing Issue.
Camshaft Adjuster.

Checks:
Check Setting of Timing Belt.
Check Timing of Intake/Exhaust Cams.
Check Cam Adjusters as per Repair Manual.

Nov 14, 2013 | 2004 Toyota Prius

1 Answer

P0016 what is that n how u fix it


P0016 Crankshaft Position - Camshaft Position Correlation
P0135 O2 Sensor Heater Circuit
P0138 O2 Sensor Circuit High Voltage
P0340 Camshaft Position Sensor "A" Circuit
P0344 Camshaft Position Sensor "A" Circuit Intermittent
P0508 Idle Air Control System Circuit Low
P0522 Engine Oil Pressure Sensor/Switch Low Voltage
_____________--
JMA TRS-5000 Cloning Machine

Jun 03, 2013 | Cars & Trucks

1 Answer

P0018


P0018 - Crankshaft Position Camshaft Position Correlation Bank 2 Sensor 'A'

P0018 Description Crankshaft Position Camshaft Position Correlation Bank 2 Sensor 'A' is the generic definition for the P0018; however your vehicle's manufacturer may have a different definition for the P0018 code.

Sep 25, 2012 | Smart fortwo Cars & Trucks

1 Answer

Kia cord po019


P0019 KIA - Crankshaft/Camshaft Correlation Error engine cyinder Bank 2 Sensor 2

Possible causes- Dirty Oil
- Engine mechanical problems
- Camshaft timing incorrectly set
- Faulty camshaft position sensor
- Faulty crankshaft position sensor
- Faulty actuator assembly

Jun 26, 2012 | Kia Cars & Trucks

1 Answer

P0016 for a 2002 solara


P0016 Crankshaft Position/Camshaft Position Correlation Bank 1 Sensor A
take the engine out ,someone having a laugh at your expense or what

Mar 23, 2012 | Toyota Cars & Trucks

Not finding what you are looking for?
2003 Kia Sedona Logo

Related Topics:

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...