Question about 2004 Nissan Murano

Open Question

2004 Nissan Murano how to replace engine mounts?

Dealer said that 3 engine mounts need to be replaced. Where are they on the engine?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

insanegtp
  • 112 Answers

SOURCE: 2004 Nissan Murano How do you clear maintenance light after oil change?

press maintanence button until you see engine oil, then hold trip/reset button... :)

Posted on Oct 03, 2008

billyd1973
  • 73 Answers

SOURCE: 2006 nissan murano headlight out

Bulb can be replaced. You can buy at Walmart or your local parts store. I recommend replacing both. They are rated for the same amount of run hours and will usually fail within the same month.

You can also buy from this link.
http://www.partsgeek.com/gbproducts/YN/B18919-HEL-P8040.html?utm_source=google&utm_medium=ff&utm_term=06+2006+Nissan+Murano+Headlight+Bulb+Hella+Nissan+Headlight+Bulb&utm_content=YN&utm_campaign=PartsGeek+Google+Base

Posted on Jan 16, 2009

  • 1 Answer

SOURCE: 2004 Nissan Murano, back door can't open

I had a similar problem with a sienna and sometimes the cable ( inside the door) between the handle and the latch gets stuck in the sleeve. Kind of like the brake cable on a bike.
take the panel off by removing all the screws you can see on the panel and pull the panel off. There will be plastic pins holding it. Some of them may pop off and some will break off.
Drip oil down the sleeve so the cable slides freely. I used bike chain oil. Do not use WD40. This is **** and will not work for very long. Try the handles a few times before you put the panel back.

Posted on Mar 03, 2009

  • 3 Answers

SOURCE: Replace rear wiper on 2005 Murano

You probably already figured this out, but you have to remove the wiper arm completely in order to replace the wiper blade.

The blades are an unusual size (somewhere around 14 1/2") and I believe they are only available from a Nissan dealership. They include printed instructions in the box but just in case, this is from the official Nissan service manual:

88b7c7f.jpg

moz-screenshot-61.jpg9b7da18.jpg








Posted on Jun 29, 2009

yegarboy
  • 286 Answers

SOURCE: replace 2004 nissan quest motor mounts

Get a piece of 2x4 and a floor jack. Support the bottom of the engine with the 2x4 under the oil pan. Slightly raise the jack untill slight tension is felt. Loosen the top motor mout bolts and remove the mount. Install the new mount lower the jack and retighten the mount. Do the same for the rear or bottom mounts witch ever applies. HTH

Posted on Dec 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a nissan murano 2005 with the code p1701 and a p0340 how can i use them to repair these codes


Nissan Murano P0340 2005 Nissan Murano - Camshaft Position Sensor Circuit
Possible causes- Faulty Camshaft Position Sensor-
Camshaft Position Sensor harness is open or shorted- Camshaft Position Sensor circuit poor electrical connection- Faulty starter motor- Starting system circuit-
Dead (Weak) battery
P1701- Fuel trim

I would suggest replacing the camshaft position sensor. When the sensor fails it can cause changes in fuel system that the computer can detect. So I suspect once the camshaft sensor ivreplaced that the P1701 code will be gone.
Cam Position Sensor Replacement Nissan Murano 3 5L

Sep 20, 2015 | Nissan Cars & Trucks

1 Answer

2004 nissan murano wont start.battery is good but when i turn the key i have nothing.


Please check your solenoid switch on starter motor. You should hear click sound while you try start the engine (You may need another person help to do this).If no sound at all, the problem is there and need to fix / replace.

Jul 02, 2011 | 2004 Nissan Murano

1 Answer

NISSAN MURANO 2004 I receive an error on my screen Check Engine & after checking at the garage the problem was P0340 what would it be ?? & how to fix ?? when running on the highway the engine...


the P0340 is a camshaft sensor code, the sensor is located in the front (passengers ) side of the engine, there should be two sensor's one for each camshaft, (front of each head) defective cam sensor's can cause the the problems of stalling and hard starting. I am a Nissan certified tech and replaced a good number of cam sensors in the past, they are quit easy to replace, they are attached by one ten millimeter headed bolt (per sensor) remove the bolt then work the sensor clockwise and counter clockwise while pulling out, there is a o ring seal on the sensor and when installing the new one lightly lube o ring before installing, then install sensor and be sure it fully seated against the mounting surface before installing the bolt or you will break the mounting ear of your new sensor. thanks for using fixya

Jan 01, 2011 | 2004 Nissan Murano

1 Answer

My Nissan Murano thumps anytime i stopped what it means?


engine mounts may be worn or broken.. check by holding down brake pedal while pushing on gas in gear to see if engine lifts/falls. Check all suspension components for wear or damage.

Sep 16, 2010 | 2004 Nissan Murano

1 Answer

Engine motor mounts


2 for the engine and one for the transmission

Mar 08, 2010 | 2004 Nissan Murano

1 Answer

I need to replace the front struts on my 2005 Nissan Murano S. Do I need to replace my strut mounts at the same time, or are they a reusable part?


I would not replace them unless they are obviously bad. If replacement is neccessary, use dealer parts. NON Nissan parts are not as good of quality.

Sep 16, 2009 | 2005 Nissan Murano

1 Answer

2004 Nissan Murano Alternator


This issue is under recall. If you have not had it replaced by a dealer, call immediately! I believe the recall involves the mounting bracket breaking.

Apr 18, 2009 | 2004 Nissan Murano

2 Answers

2003 Nissan Murano Spark plug removal ( rear babk ) - the fastest way to do it.


yes i have done this myself many of times on all transverse mounted motors. also another approach you can use is to put the vehicle on jack stands and remove the plugs from underneath. then you don't have to remove the dog bone mounts. hope this helps

Oct 23, 2008 | 2003 Nissan Murano

Not finding what you are looking for?
2004 Nissan Murano Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...