Question about 2004 Ford Explorer Sport Trac

Open Question

Does explorer sport trac had a voltage regulator

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on

Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Posted on Apr 02, 2009

Ad
  • 12 Answers

SOURCE: how to change fuel filter on 2001 ford explorer

it in the tank so your gonna either gonna have to drain the tank and lower it to the ground,it shouldn't take more than 30 minutes.make sure you put the seal back in right,so it won't leak,it aint very hard.

Posted on Jul 12, 2009

  • 5546 Answers

SOURCE: 2004 FORD EXPLORER SPORT TRAC POWER WINDOWS AND

Look in the owners manual and see if they have a circuit breaker or relay instead of a fuse. It could be bad and you would not see it.

Posted on Jul 23, 2009

  • 1 Answer

SOURCE: 01 ford explorer sport trac rear timing chain diagram

They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?

Posted on Nov 18, 2009

  • 18 Answers

SOURCE: how do i reset the check engine light on my 2003

Unplug the battery for about 10 min then plug it back up start the engine. the computer should reset, if the light comes back on then u still have problems.

Posted on Jan 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced Fuel filter and fuel pump on my 2002 Ford Explorer Sport Trac. I have no fuel pressure. The voltage to the pump initially is there when I try to start but drops to 6 volts. What is the issue?


Make sure battery has a full charge and battery connections all good. Use a digital multi meter across battery posts, have helper turn key to crank, how far does the voltage drop? Generally it shouldn't drop below 10 volts, that spec is subjective, but, if the reading drops way down there, I'd check the battery and connections.
You could check voltage at inertia switch. That might give you an idea if the problem is before the inertia switch or after?

Nov 04, 2016 | 2002 Ford Explorer Sport Trac

1 Answer

How to replace headlight bulb on 2007 ford explorer sport trac


How To Install Replace Headlight Ford Explorer Sport Trac ...

? 4:28
https://www.youtube.com/watch?v=NzMVcCsZ860
May 11, 2010 - Uploaded by 1A Auto Parts
How To Install Replace Headlight Ford Explorer Sport Trac 01-05 1AAuto. .... We offer the replacement headlights on our website for your truck.

Jan 11, 2016 | 2007 Ford Explorer Sport Trac

1 Answer

How to remove a power window motor on a ford explorer sport trac passenger door


The regulator has to be removed first. I would first check the connection to the motor , make sure it is clean and has the correct voltage under load .

Aug 16, 2014 | Cars & Trucks

1 Answer

Voltage regulator


Alternator voltage regulator! Depending on the Alternator and model, it is either located inside of the alt (defective return it and replace) or it it mounted externally. remove and replace

Nov 09, 2013 | 2004 Ford Explorer Sport Trac

1 Answer

2001 explorer sport trac crank sensor location


The Ford Explorer Sport Trac is a mid-size sport utility vehicle with a pickup truck. The Explorer Sport Trac was introduced in 2000 as a 2001 model.-------------------------------------------------------------------------------------------
Multi-Di@g Access

Jan 14, 2013 | Cars & Trucks

1 Answer

2001 Ford Explorer Sport Trac V6 having issues, it tends to start hard and idle hard initially. It generally will only start if I turn the ignition and apply the gas reving the engine around 2000 rpm for...


First thing would be to replace the fuel filter. Then spark plugs. You may have a weak fuel pump. A faulty fuel pressure regulator could also cause this.

Sep 29, 2010 | 2001 Ford Explorer Sport Trac

1 Answer

My drivers side electric window stop working 2002 ford sport trac. how do you change the motor


To remove the door panel, phillips head door screws should be removed, and the panel should slide up. Next, unbolt the window from the regulator and remove the window from the door. Then unbolt the regulator. The regulator and the motor have to be removed together. The motor will be mounted to the door on the inside. There should be three screws or nuts (10mm) holding the motor in. Remove motor and regulator. Reverse to reinstall.

Jul 11, 2009 | 2002 Ford Explorer Sport Trac

1 Answer

Replacing the Altanator for 2005 sport track


It is probably the voltage regulator that is connected to the altenator.

Jul 07, 2009 | 2005 Ford Explorer Sport Trac

1 Answer

2003 sport trac turned over started...died will not restart.


Could be bad altenator, voltage regulator, or battery. If the check engine light is on, it is most likely a bad sensor. The car will have to be put on scanner to find out exact reason light is on.

Jun 22, 2009 | 2003 Ford Explorer Sport Trac

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...