Question about 1998 Ford Contour

Open Question

A diagram of a 98 ford contour cam sensor - 1998 Ford Contour

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: need a diagram for serpentine belt 1998 Ford Contour 4cyl 2.0l.

98 ford contour 2.0 belt routing

here is a picture of routing and how to do it , etc. , good resource ..

J5

Posted on Jan 19, 2009

Ad
  • 23 Answers

SOURCE: 1998 ford ranger cam shaft sensor

there is a tool to line up the sensor while at top dead center on #1 cylinder you put it on top of the syncronizer fords name for the oil pump drive & interupter. good luck from schleck.

Posted on Sep 03, 2008

  • 1 Answer

SOURCE: 1998 ford contour fuse diagram

dont have an actual diagram but if you check at mastercraft.com they have a copy of the owners manual online and its free to access.

Posted on Dec 26, 2008

Molson02536
  • 3854 Answers

SOURCE: illustrated diagram on how to remove speed sensor for windstar 98

The Vehicle Speed Sensor is located on transaxle, at the rear of the engine. I would check the harness connector to be sure it is clean and connected tightly. Also check the wiring for cuts and chaffing. Since it is fairly inexpensive, only about $42.00 from Ford, you may want to consider replacing it, at least to eliminate it as a possibility. You may want to go to a muffler shop to have this done like speedy, I believe the flex pipe needs to be undone to get to the VVS. If there is an Auto Zone around your area, you could always ask them for the step by step instructions to replacing the VVS, and it's free of charge. Good luck and hope this helps.

Posted on Jun 11, 2009

  • 5 Answers

SOURCE: WIRING DIAGRAM A/C SYSTEM ON A 1999 FORD CONTOUR,2.0L ENGINE

Haynes Manuals not Chiltons are the source I use for wiring. You local library might have one and photocopy it off.

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my ign fuse located on my car


Below dash instrument panel, R16 ignition relay
98 Ford Contour SE Fuse Box Map
Fuse Panel Layout Diagram Parts: passenger side air bag, heater blower, interior lighting, heater blower motor, parking lamp, interior lighting, electric mirror, clock, wiper motor, ignition, reverse voltage protection, rear window defrost, engine management system, instrument panel illumination, radio, wiper motor, power windows, ABS module, backup lamp, brake lamp, door lock, main light, cigar lighter, electric seats,
link below should be the same as yours, press the helpful button

http://www.autofuseboxdiagram.com/1342-98-ford-contour-se-fuse-box-diagram

Jan 30, 2016 | 1999 Ford Contour

1 Answer

I nee instructions on a cam sensor removal for a 1998 ford contor with a 16 vale 2.o over head cam engine


The camshaft sensor is located at the back of the head on driver side. Remove the wire,unscrew the sensor,screw the new sensor in the head and put the wire back on the sensor

The camshaft sensor is not in the back on the 98 4 cyl its right in front. All you need to do is take off the 3 bolts on the top of the heat shield and pull it back a bit and it will be right there.

Apr 24, 2010 | 1998 Ford Contour

2 Answers

98 ford contour wiring diagram


When you tell us "wiring diagram", is for one specific circuit or you are refer to the firing order?

Apr 13, 2010 | 1998 Ford Contour

1 Answer

Need diagram for 1998 Ford Contour serpentine belt.


1998 FORD CONTOUR - L4 2.0L 1989cc 121ci BI-FUEL FI N Z

Multiple Accessory, w/o A.C.
76f0cdb.jpg


Multiple Accessory, w/A.C. (Mfg. After 2/98)
0e0818e.jpg

Multiple Accessory, w/A.C. (Mfg. Before 2/98)
d6d97b4.jpg

More details, can find in DAYCO Catalogue

I hope helped with this. Good luck (remember rated thie help).

Dec 04, 2009 | 1998 Ford Contour

1 Answer

98 ford contour hesitates when raining/wet


has the system been tested for trouble codes? if none are present replace the MAF sensor.

Jun 18, 2009 | 1998 Ford Contour

1 Answer

CHECK ENGINE LIGHT CODE 1381


the actual code is "Cam Timing Advance is excessive"
check your cam timing your timing belt may have slipped a tooth

May 16, 2009 | 1998 Ford Contour

2 Answers

Need a diagram for serpentine belt 1998 Ford Contour 4cyl 2.0l.


98 ford contour 2.0 belt routing

here is a picture of routing and how to do it , etc. , good resource ..

J5

Jan 19, 2009 | 1998 Ford Contour

Not finding what you are looking for?
1998 Ford Contour Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...