Question about 2005 Jeep Liberty

Open Question

2005 liberty gas gauge doesnt work

Checked gauges and they are all good

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 375 Answers

SOURCE: gas gauge no longer works

The light behind myRemove the cluster bezel from the instrument panel. See Cluster Bezel in this group for the procedures.
Remove the four screws that secure the instrument cluster to the instrument panel Instrument Cluster Remove/Install
Pull the instrument cluster rearward to disengage the two self-docking wire harness connectors
NOTE: The instrument cluster has two self-docking wire harness connectors that will be automatically aligned with, and connected to the instrument panel wire harness when the cluster is installed in the instrument panel.
Remove the instrument cluster from the vehicle.
Reverse the removal procedures to install. Tighten the mounting screws to 2.2 N·m (20 in. lbs.)
when I turn my headlights on. All the other gauges are lit, but not the gas gauge. How do I get in there to replace the bulb and fix this? Or is it a fuse problem? I have a 1998 jeep scout Thanks

Posted on May 14, 2008

  • 1 Answer

SOURCE: 96 jeep grand cherokee wont start

my 1996 jeep is doing the same thing.the fuse I have been changing is under hood in fuse panel on left 20 amp sm. in center of fuse panel closest to bat.

Posted on Aug 22, 2008

rteemon
  • 578 Answers

SOURCE: INSTRUMENT PANEL GAUGES DON'T WORK

check your vehicle instrument module

Posted on Jul 02, 2009

  • 4 Answers

SOURCE: gauges fail to work n 96 jeep cherokee

check for loose or dry rotted wires around the fuse box under the hood it fixed mine good luck

Posted on Jul 08, 2009

jonathancole
  • 127 Answers

SOURCE: jeep liberty gas gauge stuck on half tank

three things the gauge is out or the sending unit is out or voltage regulater the sending unit is in the gas tank this is also the fuel level sensor the voltage regulator is usually on the alternator if its stuck on half then it might just be the gauge

Posted on Aug 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 chevy cavalier gas gauge doesnt work goes into the temp gauge and when i try to put gas in it spills out like it is full.


It sounds like the fuel gauge sender unit is faulty, probably causing a wiring problem with other dash dials. Also sounds like you already full of fuel. The float and sender unit need checking and/or replacing.
(float in fuel tank). The fuel tank needs to be drained completely to do this work. Is it something you can do ? If not, it's not a major operation for a mechanic and the parts are cheap. Good luck... Red.

Jan 29, 2016 | Cars & Trucks

1 Answer

Fuel gauge doesnt work


Is this the only gauge on the vehicles instrument panel(cluster) that doesn't work? Check fuses. May need to check this from tank unit wire harness by gas tank for bad gauge or defective tank unit. Good luck, best regards.

Feb 09, 2011 | 1997 Chevrolet Blazer

1 Answer

My gas and temp gauge doesnt work. When i turn on the car they spin all the way around. i never know how much gas i have.


This is common on the 03-05 Cavalier instrument clusters, it's caused by failing stepper motors on the cluster's circuit board and can be fixed. Check out this site for more on how to get it repaired - Cavalier gas gauge broken

Jun 22, 2010 | 2005 Chevrolet Cavalier

1 Answer

Jeep liberty gas gauge stuck on half tank


three things the gauge is out or the sending unit is out or voltage regulater the sending unit is in the gas tank this is also the fuel level sensor the voltage regulator is usually on the alternator if its stuck on half then it might just be the gauge

Aug 13, 2009 | 2002 Jeep Liberty

2 Answers

Why doesnt my gas gauge work after installing new fuel pump?


check to make sure the wires are all connected at the sending unit,check to make sure you have a good ground.

Apr 09, 2009 | 1996 Dodge Dakota

1 Answer

2005 v6 instrument cluster problems


mustangs of your year are known for having defective stepper motors installed in the gauge cluster. Having someone replace the bad motor with the newer p/n motor should be a lot cheaper than replacing your cluster at the dealership.

Mar 29, 2009 | 2005 Ford Mustang

1 Answer

Gas gauge doesnt work


There is a Sending Unit for the Gas Guage Under the Dash I Believe. It usually Runs about $750.00 Just for the Unit. I agree with you!

Feb 01, 2009 | 2006 GMC Envoy

1 Answer

Gas gauge does not work


check with GM on a recall

Dec 06, 2008 | 2005 Chevrolet Impala

Not finding what you are looking for?
2005 Jeep Liberty Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...