Question about 2001 Mitsubishi Diamante

1 Answer

Trying to replace lug studs 2000 chevy venture.rotor is off still no room to put on new studs. Pretty sure autoparts gave me correct studsd

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 5,332 Answers

There should be a certain position that the hub can be rotated to that will let you sneek the new stud in. If you can't find that position than remove the three bolts on the backside of the knuckle that hold the hub to the knuckle. this will allow you to pull the bearing/hub out of the knuckel enough to sneek the new stud in.

Posted on Feb 10, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need help to change front wheel stud on 1999 honda civic EX


1. first take the wheel off so you can see the the caliper and the rotor. make sure the car is on stands and not just waving around on a jack.
2. look behind the caliper and use your finger to locate, a pair of bolts behind the caliper... they will be holding the caliper into place on the suface of the rotor, by a simple look and feel you can see these, they should take a 17mm socket undo them and remove the bolts. at this stage you should see the the caliper become loose.
3. remove the caliper by pulling it up and away from the rotor
4. now you can see the rotor remove this it will simply slide away.
5. this will leave the hub exposed and the studs.. you will see that they are wedged into the hub
6. remove the stud/s by hitting them / it with a hammer be carful to not damage the other studs if you just replacing one.
7. there is one spot where the will be a gap and you will be able to get the stud in behind the hub and have a little bit of room, rotate the hub to there, make sure the car is out of gear or this will be very difficult :)
8 once the stud is in take something you can use as a spacer like a larger then the stud nut. for example and then put one of the wheel nuts on and tighten slightly
9. use a hammer and drive the back of the stud home, and slowly tighten the wheel nut as you go.
10. once this is done your finished put all the bits back togeather in the oppersite order and replace the wheel.






source:http://wiki.answers.com/Q/How_do_you_replace_front_wheel_stud_from_a_1999_honda_civic

Jul 30, 2008 | Honda Civic Cars & Trucks

2 Answers

How do I replace all five lug nuts on front driver side wheel?


They are pressed in from the backside of the wheel hub that the studs stick out from. And not like needing a heavy press- once you get the old studs driven out (usually works with a hammer or small mallet), you can easily draw the new studs right into a snug fit by using the lug nuts, the new ones you just bought along with the 5 new studs, available at most any parts store.

See it's not the lug nuts that are broken, those nuts tighten the tire to the hub by the lug nut studs that the tire fits over. It is the studs themselves that are breaking off. This is common enough that parts stores carry replacements. A chevy dealership might have just your size in stock, if you don't mind paying extra high dealership charges, but it might not be that much for these rather inexpensive items. In a lot of cases, the studs can be removed from the hub as it sits, but there are cases where the hub must be removed from the vehicle for stud replacement. You can eyeball it and pretty much tell if the studs can be removed easily, after you take the wheel (tire) off. For any work on the vehicle, don't rely on the jack. Use blocks or jack-stands always.

Oct 25, 2015 | 2000 GMC Jimmy

1 Answer

Saturn vue


Are you saying that you are trying to replace the lug stud? The studs are pressed into the spindle that the rotor is mounted to. It is possible to pull the stud thru the spindle by tightening the lug nut, but this is not the proper way to do it. The proper way would be to remove the rotor and the spindle from the vehicle and press the lug stud into the spindle with a press. But I have pulled studs into the spindle when I was broken down on the side of the road with 5 broken studs. You just have to make sure you tighten the nuts until they do not tighten anymore, and check the nuts every day until they do not tighten anymore.

Sep 01, 2014 | Saturn Vue Cars & Trucks

1 Answer

Chevy camao


Not necessary to remove axles. Remove drum or rotor, hammer through the damaged stud, has room to fall out behind axle flange. Insert new stud through opening, A stud installer is preferred at this point, however, you can also use a couple of stacked washers and a lug nut. grease the washers, place them over the stud, grease the stud threads and then thread on the lug nut. With a socket wrench ,crank the stud down. The splines on the stud will bite in , keep turning until stud base meets axle flange. A new lug nut may be required , the one you use as an install tool may get damaged.

Jan 08, 2014 | 1998 Chevrolet Camaro

1 Answer

I need to know how i replace the 5 lug nut studs on the front of a chevy venture?


If you mean the threaded studs that the lugs screw onto, click my screenname and go to my Tips and Tricks - I wrote up a procedure there on exactly how to do it.

Jul 13, 2010 | 2001 Chevrolet Venture

1 Answer

How to get front rotors off and r they nock offs or do i have to take a nut off? 2000 chevy silverado 2wd


mcdevito75 here, They should be knockoffs, That castle nut is holding the hub / Bearing assembly to the axle, and once removed that nut has to be replaced with a new one, so it"s not reasonable that nut has to come off to get the rotors off. Try, remove the tire and lift the caliper assembly off the rotor, use penetrating oil, liquid wrench, W D 40 around the lugs as they may be part of the rotor assembly, Then with a hammer tap moderately around the edge of the rotor to loosen it, keep the gear in Neautrel so you can turn the rotor while tapping with the hammer and use that penetrating oil around the lug studs and around the hub. The rotor should fit around the hub where that nut is and thru the lug studs that hold the tire on the axle.

Jun 17, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

We had a new serpentine belt replaced a couple of months ago and it just came off. How can I put it back on? Also the lug nuts seem to be stripped.


Click on the following free direct Link. It has the Serpentine Belt Diagram and Tensioner location for your 2000 Saturn SL.

http://www.2carpros.com/car_repair_information/year/2000/make/saturn/model/sl/2000_saturn_sl_drive_belt_routing_diagram.htm

Before we get to putting it the Belt back on...
Look at the alignment of the Pulleys. Most times the Tensioner or Idle Pulley are "canted" - meaning pitched or leaning forward, which causes the belt to "run off" the pulley - throwing the belt.
With the Belt off: check side-to side play for each one of the Pulleys by hand, especially for the Tensioner and Idle Pulleys. There should not be any side-to side play. If there is any other Pulleys that are canted - check if they are properly tightened. A new belt should not have come off on it's own without some other problem.

GENERAL/Standard Rules to Removal the Serpentine Belt with a Tensioner:
A. Find the Tensioner(s). (See Diagrams on Link)
B. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
C. Remove the loosened belt off one of the other more easily accessed Pulleys.
D. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.


Regarding the Strip Lug -Studs.
Is this on the wheels with Rotors (Disc) or Drums? If the tire was not properly mounted, or the Lug Nuts were not properly Torqued; this will cause the Lug Studs (bolts) to be stripped.
With the vehicle raised and properly supported by jack stands:
For Rotors:
Remove the Tire, Brakes (Calipers/Pads) and Rotor, exposing the Wheel Hub (Bearing) Assembly with the Studs fully exposed. Rotate the Wheel Hub to a location where the Lug Studs can be clearly removed FROM THE REAR OF THE WHEEL HUB ASSEMBLY.
Using a impact hammer or mini sledge hammer: Hammer the Lug Studs back thru the Wheel Hub Assembly.
Remove the loosened Lug Studs.

For Drums:
Raise, support, remove the Tires.
Remove the Drums off the Wheel Assembly.
Using a impact hammer or mini sledge hammer: Hammer the Lugs back into the drum, removing from inside the Drum

Purchase the new, correct size and length Lug Studs and new Lug Nuts. If the Studs were stripped, most like the Nuts are too.
To reinstall the Lug Studs: Purchase an additional two (2) Lug Nut that fits that Lug Stud. Also purchase several Large Heavy Duty Washers that can fit on the the Lug Studs.

Place the Lug Stud back into the Wheel Assembly from the Rear (Rotors) or from inside (Drums). Use High Temp Grease for the area of the Lug Stud Splines that have to be "drawn" into the Wheel Assembly (with Rotors) or into the Drum.
After the Lug Studs are "IN" as far as they will go: on the outside place at least two (2) of the Washers on Lug Studs. Use a Lug Nut and tighten as far as possible down-on the Lug Stud as possible.
Next: Using an Impact Wrench tighten that Lug Nut down/on, drawing the Lug Stud into the Wheel Assembly/Drum. Check the rear of/inside the Wheel Hub Assembly/Drum. The Heads of the Lug Studs should be firmly against the Wheel Assembly/Drum.
If you do not have a Impact Wrench - use at least a 24-in Breaker Bar and Tighten the Lug Nut on, drawing the Lug Stud into the Wheel Hub Assembly/Drum. This takes longer and alot more work, compared to 10-seconds using the Impact Wrench.
Repeat as necessary.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

Mar 31, 2010 | 2000 Saturn SL

2 Answers

Broken wheel stud front left 1992 honda accord


Only if there is an Acsess Hole Directly Behind the STUD'S PUNCH THE Broken SHORT one OUT But there May Not Be Enough ROOM FOR the NEW LONG STUD to go in between the HUB & Rotor Check this FIRST If you see GOOD CLEARANCE TO GET The new STUD in Then just Drive the old one out , and Use A LARGER than Stud Nut Or Washers to Pull New Stud Threw some Before Putting Wheel on. Then Put Wheel on And Tighten Wheel , Retorque after a Few Hundred Miles.

Mar 29, 2009 | 1992 Honda Accord

2 Answers

Instructions to replace sheared off lugs / studs - 1997 Chevy


You can remove old lug by driving it out with a decent sized hammer. To re-install, push new one into flange from backside and stack washers on wheel side, leaving enough room for the lug nut to go on. (backwards...flat side in) Tighten the nut, pulling the lug into the flange, till it is flush (like the unbroken ones) I suggest that you put some lube on lug threads to prevent binding while doing this.

Mar 16, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
2001 Mitsubishi Diamante Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...