Question about 2003 Dodge Sprinter

1 Answer

Fuel pump circuit

I have no voltage going to my in tank fuel pump, and i have no reference manuals to help me. Can someone please let me know where the fuel pump relay is.... or any other advice.


By the Way--- the problem with the van was started by using gasoline instead of diesel, then a fire, then the guy driving it took it apart, then he brought it to me to fix. I've replaced the engine harness and the body harness (they were both fried)....now i am just starting to try to make it live again...any help would be greatly appreciated

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

In fuse cluster under hood lid so diagram to fuel pump relay!

Posted on Jan 07, 2009

1 Suggested Answer

  • 512 Answers

SOURCE: Fuel pump not pumping??

under the left side of the dash is the fuses and relays....check fuse 16 and 6 for power....the asd relay is also located here....if it has power and no ground possible wiring problem or enine control module

Posted on Oct 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel control module 2008 escalade and the fuel pump quit working.if I run a hot wire to it it will run but as soon as I remove the hot wire it quits


Ran a hot wire to what fuel pump or the control module ? Which of these is yours ?
Figure 9: Fuel Controls - Fuel Pump Controls (LY6)
Figure 10: Fuel Pump Flow Control Module (Except LY6) Does yours have fuel pump flow control module under the vehicle Fuel Pump Flow Control Module (except LY6)
Mounted to the left side of the frame assembly below the driver seat ?
Fuel Pump Flow Control Module (FPCM) - LMF
The fuel pump flow control module (FPCM) is a serviceable GMLAN module. The FPCM receives the desired fuel pressure message from the engine control module (ECM) and controls the fuel pump located within the fuel tank to achieve the desired fuel pressure. The FPCM sends a 25 KHZ PWM signal to the fuel pump, and pump speed is changed by varying the duty cycle of this signal. Maximum current supplied to the fuel pump is 15 amps. A liquid fuel pressure sensor provides fuel pressure feedback to the FPCM.
Electronic Returnless Fuel System (ERFS) - LMF
The electronic returnless fuel system is a microprocessor controlled fuel delivery system which transports fuel from the tank to the fuel rails. It functions as an electronic replacement for a traditional, mechanical fuel pressure regulator. A pressure vent valve within the fuel tank provides an added measure of fuel pump flow control module (FPCM). Desired fuel pressure is commanded by the engine control module (ECM), and transmitted to the FPCM via a GMLAN serial data message. A liquid fuel pressure sensor provides the feedback the FPCM requires for Closed Loop fuel pressure control.
If your vehicle has this system check it for DTC'S - diagnostic trouble codes . Will take guess work out of it .
DTC P0191: Fuel Rail Pressure (FRP) Sensor Performance
DTC P0192: Fuel Rail Pressure (FRP) Sensor Circuit Low Voltage
DTC P0193: Fuel Rail Pressure (FRP) Sensor Circuit High Voltage
DTC P0230: Fuel Pump Relay Control Circuit
DTC P0231: Fuel Pump Control Circuit Low Voltage
DTC P0232: Fuel Pump Control Circuit High Voltage
DTC P023F: Fuel Pump Control Circuit
The engine control module (ECM) supplies voltage to the fuel pump flow control module (FPCM) when the ECM detects that the ignition is on. The voltage from the ECM to the FPCM remains active for 2 seconds, unless the engine is in crank or run. While this voltage is being received, the FPCM supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.
DTC P025A: Fuel Pump Control Module Enable Circuit .
Ford Electronic Returnless Fuel System Diagnosis Part 1 this for ford but the GM system works the same . You'll need a wiring diagram so you know what wires are what . Free wiring diagrams http://www.bbbind.com/free_tsb.html

Oct 31, 2016 | Cars & Trucks

2 Answers

03 chevy impala how to fix pocode 1635 is this the computer are what is it


DTC P1635
The powertrain control module (PCM) provides 5 volts to the following sensors:
?€¢
The manifold absolute pressure (MAP) sensor


?€¢
The exhaust gas recirculation (EGR) valve


?€¢
The fuel tank pressure (FTP) sensor


?€¢
The throttle position (TP) sensor

These 5-volt reference circuits are independent of each other outside the PCM, but are bussed together inside the PCM. Therefore a circuit condition on one sensor 5-volt reference circuit may affect the other sensor 5-volt reference circuits. The PCM monitors the voltage on the 5-volt reference circuit. If the PCM detects that the voltage is out of tolerance, DTC P1635 sets.
Diagnostic Aids
?€¢
If any sensor using a 5-volt bias voltage, such as the intake air temperature (IAT) sensor or fuel sensor, is shorted to voltage, DTC P1639 may set in addition to DTC P1635.


?€¢
For an intermittent condition, refer to Intermittent Conditions .


Does the vehicle start an run ?

Jun 11, 2015 | 2003 Chevrolet Impala

1 Answer

P0449 code 1995 dodge dakota


2ec21afa-b94b-4fb4-8163-08305765a931.gif
(1)EVAP Purge Solenoid Ignition Positive Voltage
(2)To Intake Manifold Port
(3)Fuel Tank Pressure Sensor
(4)Fuel Tank Pressure Sensor Ground Circuit
(5)Fuel Tank Pressure Sensor Signal Circuit
(6)Fuel Tank Pressure Sensor 5V Reference Circuit
(7)Fuel Filler Neck
(8)Rollover Valve
(9)Fuel Tank
(10)EVAP Vent Valve
(11)EVAP Vent Valve Control Circuit
(12)EVAP Vent Valve Ignition Positive Voltage
(13)EVAP Canister
(14)EVAP Purge Solenoid
(15)EVAP Purge Solenoid Control Circuit

check this out on your vehicle. also make sure there is no air lines leaking on the engine.

Jan 25, 2014 | 1995 Dodge Dakota

1 Answer

How to fix gas gage on s-10 blazer


Someone will need to check the circuit at the gas tank, the sending unit next to the pump grounds the gauge on the dash. You should have a voltage reference at the tank from the gauge.

Jan 03, 2013 | 1996 Chevrolet Blazer

1 Answer

P2175,po463,poo32


Hi there:

DTC P0032 - Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)
A P0032 DTC (diagnostic trouble code) refers to the O2 sensor (oxygen sensor) located on Bank 1 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2.

This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. The sensor detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle's computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the O2 sensor. Essentially this P0032 code means that the resistance of the heater circuit is higher than normal. In some cases, that resistance level must be higher than 10 A to trigger the DTC code.

Note, this code is very similar in nature to P0031, P0051, and P0052

Most likely you'll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate.

A P0032 DTC trouble code may be caused by one or more of the following:
A short in the heater circuit in the sensor
A failed O2 sensor heater
Wiring/connectors broken/frayed leading to sensor and/or relay
Failed PCM/ECM

Possible Solutions:
To fix a P0032 DTC code, you'll need to do a proper diagnosis. To do that, you'll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you'll want to check those as well. Use a digital volt ohm meter to:

check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement)
check the ground circuit for continuity
measure the resistance of the heater circuit (done on the sensor itself)
measure the resistance and voltage of the wiring

Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is above 10 A.

With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #2 on bank 1.

Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There's also a chance that replacement parts for the P0032 code may also fall under a federal emissions warranty (check with your dealer to see if it's covered).


DTC P0463 - Fuel Level Sensor Circuit High Input
The fuel level sensor (sender) is located in the fuel tank usually integral to the fuel pump module. Usually they cannot be replaced without replacing the fuel pump module, though there are exceptions. There is a float attached to an arm that travels along a resistor which is grounded to the tank, frame or has a dedicated ground circuit. Voltage is supplied to the sender and the ground path changes according to fuel level. How much voltage depends on the system but 5 volts isn't uncommon.

As the fuel level changes, the float moves the arm and changes the resistance to ground which varies the voltage signal. This signal may travel to a fuel pump computer module or directly to the instrument cluster module. Depending on the system, the fuel pump computer module may only monitor the resistance to ground and then relay the fuel level information to the instrument panel. If the fuel level signal to the fuel pump module (or instrument cluster module or PCM (powertrain control module)) goes above 5 volts for a specific amount of time, then the module that is monitoring the fuel level circuit will record this fault code.


Symptoms of a P0463 DTC may include:
Mil (Malfunction indicator lamp) illumination
Fuel level gauge may fluctuate abnormally or read empty or full
Fuel light may illuminate and sound alarm


Potential causes of a P0463 code include:
The signal circuit to the fuel sender is open or shorted to B+ (Battery voltage)
The ground circuit is open, or ground path may have high resistance due to rust or missing ground ******** fuel tank
Damage to the fuel tank could cause problem in fuel level circuit
There's an open in the fuel lever sensor's resistor to ground
Possibly faulty instrument cluster
Less likely is the possibility that the PCM, BCM, or Fuel pump computer module has failed


Possible Solutions: Fuel pump senders normally last the life of the fuel pump. So if you have this code present, do a visual inspection of the fuel tank and wiring harness. Look for damage to the tank indicating impact that may have damaged the fuel pump or sender. Look for missing ground strap or a rusty ground where the fuel tank is grounded to the frame. Check for damage to the wiring harness connector. Repair as needed. Find out what kind of system you have and verify that voltage to the fuel level sensor is present at the fuel pump wiring harness. If not, repair the open or short in the wiring.

Doing a voltage drop test on the ground circuit can determine if there is a high resistance path in the ground circuit. You can perform this by using a voltmeter and connecting one lead to the battery ground post and the other to the fuel level sensor ground at the tank. Turn the key on (preferably the engine should be running). Ideally it should be 100 millivolts or less (.1 volts). Anything close to 1 volt indicates a current problem or a developing problem. Repair/clean the fuel level sensor ground as needed. It's not impossible that the instrument cluster has failed internally or on the printed circuit board (if applicable). These are very difficult for the layman to test. But if you have access to a wiring diagram you may be able to remove the cluster and see the damaged circuit if it's located on the printed circuit board, but otherwise you'll need a scan tool that will communicate with the instrument cluster.

A simple way to test the fuel level circuit is to provide a good ground to the fuel level sensor at the fuel tank connector. With the key on the fuel gauge should go to one extreme or the other. Removing the ground path completely should cause the gauge to do the opposite. If the gauge responds, you know the wiring that supplies voltage and ground to the fuel level sensor is good and that the instrument cluster is likely okay. The likely suspect would be the fuel level sensor itself. The fuel tank may need removal to gain access to the fuel pump module in the tank. A PCM or BCM (Body control module) failure isn't impossible but highly unlikely. Don't suspect this first.


DTC P2175 - Throttle Actuator Sys - Low Airflow Detected

Chec HERE (page 350) the PDF information about this test and solution code (P2174 and P2175).


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 29, 2012 | Dodge Cars & Trucks

1 Answer

Chevy Silverado 2002 2500 shows trouble code, P0230, and P0300


P0230 - Fuel Pump Primary Circuit Malfunction Symptoms - Engine Light ON (or Service Engine Soon Warning Light) Possible causes - Blown Fuel Pump fuse
- Open Fuel Pump Monitor Circuit
- Faulty Fuel Pump Relay
- Damaged ECM. P0230 Description The Engine Control Module (ECM) provides ignition positive voltage to the coil side of the fuel pump relay. When the ignition switch is first turned ON, the ECM energizes the fuel pump relay, which applies power to the fuel pump. The ECM enables the fuel pump relay as long as the engine is cranking or running, and crankshaft reference pulses are received. If no crankshaft reference pulses are received, the ECM de-energizes the fuel pump relay after 2 seconds. The ECM monitors the voltage on the fuel pump relay control circuit.
Please go to this LINK for P0300 diagnosis.

Feb 16, 2012 | Cars & Trucks

2 Answers

My f350 1997 will not run on the rear tank . how do i go about finding what the problem is?


well, first, to find out if its the in tank fuel pump or the tank selector valve, the cheapest and probable easiest thing to do is find the selector valve under the truck and switch the incoming fuel lines. front tank to rear tank inlet, and vice versa. If the truck still doesnt run, you either have an electrical delivery problem to the in tank fuel pump or a bad fuel pump. If after switching the lines, it does run, then you need a new selector valve

Sep 23, 2009 | 1997 Ford F350 Crew Cab

2 Answers

Replaced fuel pump in 1998 for ranger


Diagnostic Trouble Code (DTC) P0232 indicates that the powertrain control module (PCM) detected the FPM circuit voltage was high when the fuel pump was commanded off. The FPM circuit is wired to a pull-up voltage inside the PCM. The FPM circuit will go high if, with the key on and the fuel pump commanded off, the FPM/FP PWR circuit loses its path to ground through the fuel pump. The FPM circuit will also be high if the FPM/FP PWR circuit is shorted to power.
Possible causes:
No Start:
Inertia fuel shutoff (IFS) switch not reset or electrically open.
Open circuit between the fuel pump and FPM circuit connection to the FP PWR circuit.
Poor fuel pump ground.
Fuel pump electrically open.
Diagnostic Trouble Code (DTC) P0102 indicates the MAF sensor signal went below 0.39 volt (refer to Voltage to Mass Air Flow Conversion Table at beginning of this Pinpoint Test) sometime during normal engine operation (Continuous) or during Key On Engine Running (KOER) Self-Test.
Did you have the MAF unplugged?

Feb 18, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Fuel pump not pumping??


under the left side of the dash is the fuses and relays....check fuse 16 and 6 for power....the asd relay is also located here....if it has power and no ground possible wiring problem or enine control module

Oct 23, 2008 | 2007 Dodge Sprinter

Not finding what you are looking for?
2003 Dodge Sprinter Logo

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...