Question about 2004 Dodge Intrepid

Open Question

2004 dodge intrepid no fire on 31 COIL CODE PO 351

NO FIRE ON #1 COIL

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 45 Answers

SOURCE: engine turn but will not fire

Check all your electrical connections you were working near, sounds like you may have pulled a wire off a sensor (or disconnected one for the R&R of that water pump) or the ignition coil/pack. Also check for a "crank sensor" near the crank shaft some of those engines had a sensor there if that sensor is not fully connected ecm will not get the info it needs to power up... engine will not fire.

Posted on Mar 20, 2009

BPALepine
  • 61 Answers

SOURCE: # 1 injector not firing

Well you need to check the harness to see if it is getting power. You may need to take the plentum off and then unplug the harness and then reinstall the plentum but make sure that you leave the harness out so you have access to it.

Then you can make a test light or purchase one. Plug the test light into the harness and start the car. This light should flicker, if not you didn't repair the wire properly. Doesn't sound like a fuse being that none of the injectors would work if a fuse blew.

It could also be that the PCM grounded out when the mouse chewed the wire and needs to be replaced.

Don't worry about checking the ASD Relay because that would cut off all power to the injectors and coils.

Posted on Apr 23, 2009

jagjeffery
  • 318 Answers

SOURCE: 1998 dodge Neon no fire to coil

it sound like you have a bad crank sensor when the sensor gets hot it open circuits inside the sensor and you loose spark if you have access to a noid light see if you are loosing injector pulse also if so then you know its a good chance its the crank sensor

Posted on May 29, 2009

ourhowse
  • 2007 Answers

SOURCE: 97 dodge intrepid just all of sudden stopped firing

Try mass air flow sensor.

Posted on Jul 01, 2009

juncro
  • 467 Answers

SOURCE: my 1995 dodge intrepid won't start. It is getting

check the map sensor and the fuel pressure at the engine

Posted on Jul 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 dodge Dakota is running rough and the check engine light is on.


You'll have to look up the actual procedure to test the coil for code 351. The code means the computer is not able to fire the coil on demand which could be caused by several things, including a faulty computer. It could also be a problem with the wiring between the coil and the computer.

Feb 17, 2015 | Dodge Cars & Trucks

1 Answer

2004 dodge intrepid driveing down road and it died and wont start or get fire to plugs is it a sensor


More then likely yes, I would check your Crankshaft sensor, that what send the signal to the coil packs then to the spark plugs, the sensor is held on with a 10mm bolt on the side of the engine block on the passenger side.

Jun 03, 2010 | 2004 Dodge Intrepid

1 Answer

1996 Intrepid: firing order for 3.5 1996 dodge intrepid...


For the 1996 Dodge Intrepid 3.5L SOHC V6

Firing Order:
1-2-3-4-5-6

Cylinders:
......(back)
1........3........5
2........4........6
.....(front)

Ignition Coil Connections:
(back)
6....3
4....1
2....5
(front)

Let me know if this helped, or if you have additional informtion or questions. Feel Free to contact me at FixYa.com!

May 18, 2010 | 1996 Dodge Intrepid

1 Answer

P0304* Cylinder #4 Misfire on a 1999 dodge intrepid. were is this cylinder located.


This would be the forth cylinder from the front(where the pulleys,and belts are).There will be a coil,and under the coil,is a boot,connected to the spark plug.The miss fire could be any,of the three.I would replace the spark plugs (all four)and the boots.Then if the miss fire is still there,replace the coil,on number four cylinder.

Dec 08, 2009 | 1999 Dodge Intrepid

3 Answers

Engine light keeps comeing on mecanic change o2 senser worked for half hour came back on cods keep saying its miss fireing have had this problem for a month know


Start Small work to Big = Saved Money!
The Code(s) should be telling the specific cylinder(s) that are misfiring. Do you know waht the code is?
Target those cylinders 1st before testing the unaffected cylinders.
The following should isolate the problem(s).
1. Spark plugs - take out-reconnect back to wires and test spark plugs for getting sparks. If none: Don't replace them yet. GO TO 2. If the spark plugs are worn, dirty them replace them.
2. Remove spark plugs form end of ignition wires and test for spark from the wire. If none: Don't replace them yet. GO TO 3.
3. Remove the wires from the coil connection and test the coil for spark for each cylinder. If none: Don't replace it yet.
4. Test each spark plug and wires this way.
5. Coil Packs normally provide fire for 2-cylinders at the same time. The two are paired across from one another.
6. Test the coil for fire, amount of fire and if there is both cyclinders firing.
Misfire and the O2 Sensor got replaced??
Good Luck and get back with me if you need additional help or if this solved the problem.

Nov 20, 2009 | 2004 Dodge Intrepid

2 Answers

I have a 2004 Dodge Intrepid ---- It is showing 3 error codes/ P0300 - Engine Miss fire Detected : P0356 Ignition Coil 6 Control Circuit: P0132 - Ho2s circuit low voltage bank, sensor 1...


ok means that you dont have spark plug explotion on 1 or more cylinders and that means miss fire.

Disconnect the battery like 20 or 30 min and then connect the battery again and start the car, then drive and scan again, if you have same code you can do this:


1. take off your O2 sensor and test check if there is wrong change it because maybe that is the problem of all!

2. take off your spark plugs and put new ones.

if not work... do this.


reset your ecu (like I say before)
take your ignition coil #6 and change the place with another one on the same head side.

assambly and go to test if the DTC change like hummm example: Ignition coil #4 then or any other, then you know that the problem is your ignition coil.

if not work this... do this..

take off your ignition coil from the spark plug but still plug to the harnes (the ignition that is failing) and then take the ignition coil closer to Ground (another metal) and then start the car you need to see how the elctricity (not know how to say) "energy" jumps from the coil to the graund many times

if not are any energy jump you need to do this...

check the harnes like maybe that is the problem the question here is do you have voltage in the harness?

hope this help you.

Oct 16, 2009 | 2004 Dodge Intrepid

1 Answer

Engine turn but will not fire


Check all your electrical connections you were working near, sounds like you may have pulled a wire off a sensor (or disconnected one for the R&R of that water pump) or the ignition coil/pack. Also check for a "crank sensor" near the crank shaft some of those engines had a sensor there if that sensor is not fully connected ecm will not get the info it needs to power up... engine will not fire.

Mar 20, 2009 | 1998 Dodge Intrepid

1 Answer

No fire from coil to plugs


no fire from coil to plugs means that the coil is bad

Dec 29, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
2004 Dodge Intrepid Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...