Question about 2004 Nissan Murano

Open Question

Torque specs for 2004 Murano Lower Oil pan - 2004 Nissan Murano

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

insanegtp
  • 112 Answers

SOURCE: 2004 Nissan Murano How do you clear maintenance light after oil change?

press maintanence button until you see engine oil, then hold trip/reset button... :)

Posted on Oct 03, 2008

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 1 Answer

SOURCE: 2004 Murano has an oil leak near the oil filter

The oil filter mounts on an oil cooler housing that has an o-ring on the block side of it. The housing is held in place by the double ended connector bolt that the oil filter screws onto one side and the other goes into the block. This should be tighten to 37 ft/lbs. prior to installation of the oil filter. It may be loose or the o-ring might need replacement.

Posted on Apr 16, 2009

michigan man
  • 3533 Answers

SOURCE: what are the oil pan torque specs for a 1997 Mazda

try these websites www.autozone.com and the other one is www.alldatadiy.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your van.

Posted on Jun 30, 2009

  • 634 Answers

SOURCE: How do you adjust the main and power steering

there is spring loaded pulley and auto self adjusts tension,, if belt is loose then tension pulley needs to be replaced

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

98 jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs


Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

May 21, 2016 | Jeep Cars & Trucks

1 Answer

What are the oil pan torque specs on a 1987 Pontiac Fiero GT


To install: Place a 3mm bead of RTV sealant on the oil pan sealing flange.
Install the oil pan and torque the 1 inch bolts to 6-9 ft. lbs. (8-12 Nm) and the 1.5 inch bolts to 14-22 ft. lbs. (19-29 Nm).
Install the starter assembly.
Install the flywheel and clutch housing cover.
Lower the vehicle and refill the crankcase with the specified engine oil.
Start the engine and check for oil leaks.

Mar 12, 2015 | 1987 Pontiac Fiero

1 Answer

Where can I find bolt torque specs


I suggest going to an auto parts store in your area and asking for the "HAYNES" manual for your make and model. It is an easier book to read than a "Chilton'. It will have all the torque specs you need. The book will probably cost 20 - 30 dollars. This is much less than it will cost if you torque something wrong. I would be careful trusting internet sources. It is a very worthwhile investment and a complete repair manual.

Feb 20, 2015 | Cars & Trucks

1 Answer

Need torque specs for 96 yukon 5.7 liter


Here's a link to the oil pan removal guide with pan bolt torque specs.

Jan 13, 2013 | 1996 GMC Yukon

1 Answer

Locate oil drain plug


the oil pan is on the passenger side its right under the pan, be carfull its an alluminium pan and the plug strips out easily, it has a torque spec

Oct 09, 2009 | 2004 Hyundai Elantra

2 Answers

2001 Silverado oil pan gasket is it hard to change?


it can be you must remove oil filterand housing along with oil cooler lines lower trans lines you really need a repair manual for this kind of repair for torque specs and procedures

Jul 10, 2009 | 2001 Chevrolet Silverado 2500HD

1 Answer

Torque specs for Spider lower oil pan.


Try International Auto parts: http://www.international-auto.com/
They are Alfa and FIAT specialists. Maybe their mechanics can provide the info you need.

Jun 17, 2009 | 1982 Alfa Romeo Spider

1 Answer

1999 Saab 9-5 oil pan torque spec


they should be torqued with a 3/8 torque ratchet to 30 inch pounds.

Mar 06, 2009 | 1999 Saab 9-5

Not finding what you are looking for?
2004 Nissan Murano Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...