Question about Cars & Trucks

1 Answer

My car will not rev up past 2000revs lack of power

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check your Oxygen flow senser and also your carburator, that worked on my truck.

Posted on Feb 09, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Why is 4x4 reving past 2500/3000, revs rough also the check engine light is on holden told me they done check car lacks power scan find DTC P0405 stored a present code possible EGR or circuit issue

code p 0405 refers to exhaust recirculation (EGR ) valve position sensor A--low input ===causes --wiring short to ground--EGR valve position sensor---ECM
check the wiring and plug connections as there may be water in the connections causing the problem

Jul 17, 2016 | Holden Cars & Trucks

1 Answer

Honda ballade 1.8i fuel injection does rev above 2000revs/min. What could be the problem. Kind Regards, Christopher.

i would think that it is in limp mode
run the fault codes to determine the faulty sensor

Oct 24, 2015 | Honda Cars & Trucks

1 Answer

My ed falcon 5.0l runs but won't rev & lacks power Have replaced air flow meter as it runs better with it did connected Checked computer for damage & condensation & foreign debree But can't find the...

have the fault codes read as it may be a combination of faulty sensors causing the problem. The ECM fault reporrting process is there for a purpose and that is to pinpoint the fault and to save money.

Jan 24, 2015 | Cars & Trucks

1 Answer

Rattle from car at 1900revs only when in gear

moving noise is very hard to find.

could well be exhaust shields,
did you take a rubber mallet and tap the parts (exh, end to end?)
bang ,rattle, bang , repeat
seen many bad CAT (brick inside loose) rattle. hit it. bingo. there you go.

i also jam objects in cat shelds to stop them for making noise.
just for temporary to find source.

Mar 18, 2014 | 2005 Suzuki Wagon R

1 Answer

VW Bora when in first gear up until 2000 revs car has not much power and shakes at the front end even when warm!

Check your spark plugs and leads, lack of power at lower revs is usually due to poor spark.

Mar 06, 2012 | Volkswagen Bora Cars & Trucks

1 Answer

Check engine light on auto zone read codeP0404 replaced egr valve,air filter, added sea foam, and high octane booster. car still has check engine light on reading same code will not accelerate hesitates if...

When it revs high, is it down shifting? if so you may be running out of gas. low fuel pressure or lack of fuel getting to the injectors. (fuel filter)

May 02, 2010 | 2002 Chevrolet Impala

1 Answer

Running flat up to 3500rpm

What do you mean by "running flat" up till 3500 rpms?
You mean you have no power and can only rev up to 3500 rpms?
Could be a few things:
1.Your CAT is toast time for a new one.
2.Your Engine is toast time for a new one.
3.Check your coils and replace them along with spark plugs.

1.To check your CAT, you might want to dealer to do that. They will have to replace it under emissions laws.
2.Lack of power is when your 8 goes into limp mode due to bad apex seal(s). IE: blown apex seal(s).
3.Sometimes bad coils and or spark plugs will not allow the car to idle or rev past a certain point with out throwing a CEL light or flashing it on your HUD.

Mar 06, 2010 | 2005 Mazda RX-8

1 Answer

High engine rev low

I would suggest an automatic transmission flush before I did anything else.

Dec 26, 2008 | 1998 Toyota Camry

1 Answer

A3 power surges

run the fault codes
could be a transmission actuator problem as it senses vacuum changes when moving the accelerator and tries to change ratios ( 2000 to 2500 rpm indicates a ratio change which is the speed increase momentarily until the Transmission range sensor puts it back in the correct ratio for the road speed
check the wiring to the transmission
it is a sensor problem not a transmission failing

Jul 01, 2017 | 2002 Audi A6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides