Question about 2006 Ford Focus

Open Question

2006 ford focus turn signal wont work

Replaced turn signal bulb on rear right side and it does not work

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: change rear signal bulb on 2002 ford focus wagon

Open tailgate 2 screws hold housung in. Remonve the screws pull the huosing out and change bulb. On mine the housing had melted so O called the Ford garage and they got the socket out for me. I had to buy a new socket but that was it.

Posted on Aug 03, 2008

Ad

SOURCE: passenger side light and rear

check the fuses!

Posted on Oct 24, 2008

  • 2 Answers

SOURCE: Brake light, Turn signal not working rear right 06' Focus

I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems

Posted on Aug 06, 2009

  • 1986 Answers

SOURCE: How do you remove the rear light cover in order to

Open the hatch and look to the side of the housing, there should be a tab sticking out of the side of the assembly with a screw securing it in place (It's between the trim seal and the assembly). Then in the inside of the hatch, look up to where the assembly would be, and there should be a long cylindrical nut (it's made of plastic and will have a metal center for the threads). Remove this and then you can pull the entire assembly off. You won't have a lot of room though because the wires are relatively short.

Posted on Oct 19, 2009

  • 120 Answers

SOURCE: 2007 ford 500 rear turn signal bulb replacement

This is straight from the owner's manual.

#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.

Install new bulb(s) in reverse order.
Good luck

Posted on Jan 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left bleaker and break light not working. Turn signal works bleaks faster than right side.


Has the vehicle been in an accident on the left rear side. First check the bulb to be sure it is not defective, trade it out with the side that works properly to test. If the bulb works well then My thought are you may have a shorted wire. The turn signal flasher works by heat build up within the flasher the heat is caused by the load of the bulbs, the load heats the metal spring causing it to open the circuit then as quickly as it cools down the circuit closes again lighting the bulbs.
There is also a possibility of a defect in the turn signal mechanism on the steering column. The turn signal switch on many models does three different things on many models that use the same bulb element / or bulb for brake and turn on rear of vehicle. It controls the circuit for brake light by sending power both left and right side rear when turn signal is in neutral position then when turn signal is in left turn the switch cancels brake light power to left side rear and supplies flasher power to left side while maintaining brake light supply to the right side rear, and so on opposite when the right turn is chosen on turn signal switch. The turn signal indicators on the dash normally run off the same circuit as front turn signal bulb only which is also controlled by turn signal switch. Front has turn signals but no brake light.
I think there is an additional load on the left side rear turn circuit and it could be either a wire that is shorted or the turn signal switch if the same bulb element is used for both functions.
Often times if trailer lighting is connected the flasher will also blink a little faster because of the extra load of additional bulbs.

Feb 15, 2015 | Cars & Trucks

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

1 Answer

Right rear turn signal does not work


check the bulb there some bulbs have two elements in them the turn signal element might be broken change the bulb

Sep 19, 2012 | Cars & Trucks

3 Answers

2004 buick lasabre, right side turn signal blinking fast.


Check the front turn signal bulbs. This will affect the resistance in the circuit and cause the working light to flash at a much faster rate.

Aug 15, 2012 | 2004 Buick LeSabre

1 Answer

Left turn signals won't flash, Right side works fine. Replaced front and rear turn bulbs (rear was burned out). Bulbs come on fine on the left side, they just won't flash.


Gday mate, we had a problem with another late model vehicle similar to that, the bulb that was put into the reverse light was not exact brand product ( ohmage was slightly wrong ) and fowled up computer, correct bulb in place and disconnect battery to reset K A M ( keep alive memory) problem solved, BEWARE, some vehicles cannot have KAM reset except for dealer computer tethered reboot , just try putting the factory correct bulb(s) in and see how it goes, geoff. hope this helped.

Feb 11, 2012 | 1998 Buick LeSabre

2 Answers

Turn signals blink fast (lights still work)? what


Hello. This happens when one of the bulbs is starting to go bad. pull all of the turn signal bulbs and look carefully at each one. you will find one with the filaments crossed. Replace that one. J.

Jun 15, 2010 | 1998 Honda Accord

3 Answers

Right rear turn signal doesn't work and the blinker light on the inside is blinking fast, what do you recommend? It does work on the right hand side rear view mirror though


the bulb at the taillight has blown. Replace the bulb. The fast blink is the systems way of saying "Hey, we need a repair here!!"

Oct 09, 2009 | 2004 Ford F150

Not finding what you are looking for?
2006 Ford Focus Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...