Question about Cars & Trucks

Open Question

Peugeot 206 indicators and hazzards not working but flasher unit keeps clicking as normal

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ginko
  • 19396 Answers

SOURCE: fuse box diagram peugeot 206

Check the website below:

Peugeot 206 Fuses.

Posted on Mar 28, 2009

Molson02536
  • 3854 Answers

SOURCE: Constant clicking from flasher unit

The flasher unit has gone bad and needs to be changed. The flasher module is a part of the hazard module also. The clicking is the unit is still working but there is not enough voltage to activate the lights to flash. It's common on the Malibu's and other GM product cars similar to the Malibu like Grand Am's Ect. I believe Auto Zone has the replacement part for you car and is more reasonable in price then the dealer and the y also have the step by step instructions to replace the flasher module. Good luck and keep me posted, be glad to help.

Posted on Jun 03, 2009

  • 205 Answers

SOURCE: my peugeot 206 diesel keeps cutting out, now it

In my opinion cut off problem occurs if engine is not getting sufficient fuel and/or air. Clean the air filter, turbo filter and fuel filter. Check the continuity of diesel flow from filter to hdi pump. If you haven't found any problem there then the possibily the hdi pump and injectors section needs to be checked. If the car has done more than 100000 miles then clean inlet and outlet manifolds including check of turbo and EGR valve. Do everything whatever possible before you take your car to garage. If there is no luck then let your car diagnosed and check any error code recorded by ecu.

Posted on Oct 13, 2009

  • 274 Answers

SOURCE: how to turn off the airbag on peugeot 206 1.6

there should be a key switch inside the car somewhere you need to turn it to the off position with the ignition key
(it will probably be some where on the dash, in the glove box or center console)

Posted on Dec 08, 2009

  • 1 Answer

SOURCE: peugeot 206 cc fan belt change

hi ive a peugeot 206cc 02 reg, the STOP light keeps flashing ive checked the normal oil and water but alls ok so whats the problem still runs fine and temp stays where it should??? any tips??

Posted on Dec 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hazzards on pegeot 206 X Reg not working.Could this be a programing fault?


a jeep Peugeot?
hazzards?
reg?
no.
are the blinkers working (winker, repeater ,turn signals. whatever.)

Feb 15, 2014 | Jeep Cars & Trucks

1 Answer

1999 Corolla hazzard lights not working. Indicator's are, but only if hazzard switch is off?


Try replaced the hazard flasher. Usually located under the dash by the steering column area.. There is also another one for the signals so make sure you replace the correct one. Both flashers might look the same. Here is a picture below of a flasher



2_6_2012_7_39_13_pm.jpg

Feb 06, 2012 | Cars & Trucks

2 Answers

My hazards work. My blinkers do not work at all. No sound or light.


there is a separeate flasher relay for turn signals,usullay by hazzard flashers.turn on hazzards use sound to locate,turn flasher will be near.some will interchange to get you by till you can replace.

Feb 17, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Indicators are not working


had this before where the front indicators were not working and like you it drove me mad because the vehicle was booked in for its inspection.straight away i suspected the hazard switch,Anyway i had a spare flasher unit so i changed it and they worked ,So after i came back i took the old flasher unit apart and cleaned the contact on the solonoid and that started working as well when i put it back in.

Oct 24, 2009 | 2005 Peugeot 405

2 Answers

Peugeot 206 cc fan belt change


hi ive a peugeot 206cc 02 reg, the STOP light keeps flashing ive checked the normal oil and water but alls ok so whats the problem still runs fine and temp stays where it should??? any tips??

Aug 28, 2009 | 2005 Peugeot 405

2 Answers

Right turn signal is slow and left just stays on 1977 ford F100


wouldn`t hurt to have a look at the flasher unit, hazzard light are adifferent unit .you may even be able to see where it hasbeen getting hot------------ adios-ben

Aug 03, 2009 | 1981 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...