Question about 2003 Nissan 350Z

1 Answer

Keyless entry go throw putting key in +out 6 times but on 6th time it unlocks driver door and nothing happens when press button on key fob

Posted by on

  • elza1 May 25, 2009

    I did, didn't change anything..red light on dash still blinks..but the alarm will not set...thoughts/suggestions??

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,066 Answers

Replace the battery in the fob

Posted on Mar 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keyless entry remote wont progam


It will not unlock the door the first time you push the button. This only registers the key fob ID into the computer. When you press the button on the key fob, press it only once and wait for the hazzard lights to flash twice again. Then open the driver's door. The key fob will not become active until you open the driver's door.

If your hazzard lights do not flash after you press the button on the key fob, there is most likely a problem with the key fob. Either it is not the correct key fob for your vehicle, or the battery is not in correctly or the key fob is defective.

The only other advice I can give you is to have it programmed with a scan tool. This way, the scan tool can verify that the computer in your vehicle is receiving the signal from the key fob.

It can be done either way, but if the "no scanner" way does not work, the rest of the system should be checked for possible problems.

Dec 12, 2011 | 2005 Nissan Altima

Tip

2000 dodge caravan keyless entry


Here is a quick HowTo on programming your own keyless entry:

1) Turn ignition to OFF.
2) Locate the Data Link Connector, its a black 16 pin connector that is under the driver's side dash, right where your right knee would be. You have to look up into the dash from below to see it.
3) Ground pin 1 of the Data Link Connector by taking a wire or paper clip and running it from pin 1 to pin 4. Pin 4 is ground so you can just short pin 1 to 4 and it will be grounded. Grounding pin 1 tells the system you are ready to reprogram it.
4) Close all of your doors.
5) Turn the key to ACC then back off. The power door locks will lock/unlock. This is the signal that the system is ready for reprogramming.
6) Push a button on your key fob, doesn't matter which button.
7) If you have 2 key fobs, then press a button on the 2nd fob within 1 minute of pressing a button on the 1st fob. Both must be programmed at the same time. If you only have 1 fob then press a button 2 more times to signal that you only have one.
8) The doors will lock/unlock to signal the codes were received.
9) Remove the jumper wire from the data connector
Complete

on Jan 29, 2011 | Dodge Caravan Cars & Trucks

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

1996 tl keyless entry


Do you have a keyless entry FOB. If you do replace the battery then program the system. Unlock the doors turn the ignition key to the "ON" position then press either the lock or unlock button of the FOB turn the ignition key off.Now turn the ignition key on again and press either button on the FOB. Turn the ignition off again. Do this 3 times. This initiates programming for the power door locks. Press the lock button of each remote one at a time to be stored in memory. this must be done within 10 seconds of each remote.
3 remotes max. Turn the ignition off and remove the key to complete programming procedure. then test each remote.

Apr 05, 2010 | 1996 Acura TL Series

1 Answer

Keyless entry not working


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. Remove key from ignition switch. Close all doors. Open driver's door. Carry out the following within 24 seconds: Turn ignition switch ON and back to LOCK position 3 times. Remove key. Press and release driver's door courtesy light switch 3 times. Ensure doors lock and unlock. If not, wait 40 seconds and repeat procedure starting with driver's door already open. Press each remote control lock or unlock button twice. Ensure doors lock and unlock after each remote control operation. If not, proceed as follows: Press and release driver's door courtesy light switch once. Ensure doors lock and unlock twice. Repeat procedure starting with driver's door already open.
NOTE: A maximum of 3 remote controls can be programmed.

Mar 29, 2010 | 2004 Mazda 6

1 Answer

Program remote


The horn chirp can be disable by pressing the lock and unlock buttons simultaneously until the hazard lights flash, and no enable press the lock and unlock until the horn chirp.
To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.
1. Close all doors and lock all doors
2. Insert and remove the key from the ignition key cylinder more than six times within 10 seconds. (The hazard warning lamp will then flash.) NOTE: Key should be withdrawn from ignition key cylinder completely each time.
NOTE: Do not rush the insertion/removal key cycling process. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed.
3. Insert key on ignition key cylinder and turn ignition key switch to "AAC" position At this time, the new ID code is entered and original (previous) ID codes are erase.
4. Press any button on the new remote controller once. (The hazard warning lamp will then flash)
NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed and programming is successful.
If there is only one remote controller skip step 5.
5. Additional ID code entry Release the door lock, then lock again with door lock/unlock switch (In power window main switch)
6. Remove key from ignition
7. Unlock driver side door, open driver side door and then close the door. (END)

Feb 20, 2010 | 2001 Nissan Pathfinder

1 Answer

Reprogram key fob


Here is a quick HowTo on programming your own keyless entry:

1) Turn ignition to OFF.
2) Locate the Data Link Connector, its a black 16 pin connecter that is under the driver's side dash, right where your right knee would be. You have to look up into the dash from below to see it.
3) Ground pin 1 of the Data Link Connector by taking a wire or paper clip and running it from pin 1 to pin 4. Pin 4 is ground so you can just short pin 1 to 4 and it will be grounded. Grounding pin 1 tells the system you are ready to reprogram it.
4) Close all of your doors.
5) Turn the key to ACC then back off. The power door locks will lock/unlock. This is the signal that the system is ready for reprogramming.
6) Push a button on your key fob, doesn't matter which button.
7) If you have 2 key fobs, then press a button on the 2nd fob within 1 minute of pressing a button on the 1st fob. Both must be programmed at the same time. If you only have 1 fob then press a button 2 more times to signal that you only have one.
8) The doors will lock/unlock to signal the codes were received.
9) Remove the jumper wire from the data connector.
10) your done

May 15, 2009 | 2000 Dodge Durango

1 Answer

Program my remote


Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entrymag-glass_10x10.gif, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.
  • Open the driver's door. Remove the key from the ignition switch.
  • (Complete these steps within 40 seconds)
    1. Insert the key into and remove it from the ignition switch 2 times.
      (IN - OUT - IN - OUT)
    2. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    3. Insert the key into and remove it from the ignition switch 1 time.
      (IN - OUT)
    4. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    5. Insert the key into the ignition switch and leave it in.
    6. Close the driver's door.
    7. Turn the key from LOCK to ON 4 times, ending at LOCK
      (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
    8. Wait for the locks to stop, then remove the key from the ignition switch.
  • On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
    1. [For all doors unlock] press and release the UNLOCK button.
    2. [For driver door unlock] press and release the LOCK button.
  • Open the driver's door. The programming is complete. If programming did not occur, start over.

Jan 13, 2009 | 2001 Toyota Tacoma

1 Answer

2000 dodge caravan


Here is a quick HowTo on programming your own keyless entry:

1) Turn ignition to OFF.
2) Locate the Data Link Connector, its a black 16 pin connecter that is under the driver's side dash, right where your right knee would be. You have to look up into the dash from below to see it.
3) Ground pin 1 of the Data Link Connector by taking a wire or paper clip and running it from pin 1 to pin 4. Pin 4 is ground so you can just short pin 1 to 4 and it will be grounded. Grounding pin 1 tells the system you are ready to reprogram it.
4) Close all of your doors.
5) Turn the key to ACC then back off. The power door locks will lock/unlock. This is the signal that the system is ready for reprogramming.
6) Push a button on your key fob, doesn't matter which button.
7) If you have 2 key fobs, then press a button on the 2nd fob within 1 minute of pressing a button on the 1st fob. Both must be programmed at the same time. If you only have 1 fob then press a button 2 more times to signal that you only have one.
8) The doors will lock/unlock to signal the codes were received.
9) Remove the jumper wire from the data connector.

Oct 11, 2008 | 2000 Dodge Caravan

6 Answers

Keyless entry stopped working on 05 cobalt now i have to unlock door with the key and when i do that the alarm goes off. Help


Lock all the doors from the inside (with all the doors closed), unlock your driver's door by manually lifting the lock, then press it back down after you are out - this will prevent the alarm from sounding when you use the key to unlock the door.

Aug 02, 2008 | 2007 Chevrolet Cobalt Coupe

Not finding what you are looking for?
2003 Nissan 350Z Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...