Question about 2009 Dodge Avenger

Open Question

Reset change oil light on a 2009 dodge avenger

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: How do I get the "Change Oil " light to go off after change .

Turn key to the run posistion and pump the gas peadle 3 times under 5 seconds.

Posted on Jul 18, 2009

techbuster
  • 5081 Answers

SOURCE: Reset oil change for a 2008 dodge aveneger

To reset your maintenance reminder system (even if the light hasn’t come on yet), you’ll need to turn your key to on (but don’t start!) and make sure your odometer is on TRIP A. Then key off. Press and hold the Odometer/Trip button. While holding down on the button, key the ignition to on (Don’t start the engine!) The display panel will count down from “------“ to “-“Continue pressing the button until the Trip A is displayed. After this step, you are done.

Posted on Oct 21, 2009

  • 21 Answers

SOURCE: I have a 98 Dodge avenger ES,,, After im driving

could be a pluged oil filter or falty oil sending unit did you try changing your oil

Posted on Mar 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the entire headlight assembly on a 2009 Dodge Avenger?


lift the hood on the front of the rad you will find a plastic black cover , its held on with push pin fasteners to remove them you need to lift the center bit , use a small screw driver to do this the fastener now lift out there should be 6 to 8 of them now this cover will come off, you will find 4 10mm bolts that hold the light assemble in place take them out gentley remove said light , the bulb comes out with a 1/4 turn of the light socket DO NOT TOUCH THE GLASS PART OF THE BULB WITH YOUR BARE HANDS AS THE OIL ON YOUR SKIN WILL CAUSE A HOT SPOT AND BURN THE BULB OUT WEAR GLOVES IF YOU NEED TO TOUCH THE BULB! repete process to install

May 20, 2015 | 2009 Dodge Avenger

2 Answers

How do I reset the oil light on my 2009 dodge caliber after the oil has been changed?


On most cars it's a push button up under the dash near the drivers left nee.

Jul 24, 2011 | 2009 Dodge Caliber

1 Answer

Oil change light came on i changed the oil and i dont know how to reset it


the owners manuel will have that info jus look under instrument panel and it will give you instruction. if all else fails just remove your neg cable from your battery for 5 min and reconnect it :)

Jan 31, 2011 | 2009 Dodge Avenger

1 Answer

How to i remove rear lens cover to change burned out light,2009 dodge avenger


Open Trunk, There Is Some Hardware Behind The Tail Lamp That You Need To Remove, an d Then the Tail Lamp Will Come Out !!

Jan 12, 2011 | 2009 Dodge Avenger

3 Answers

I have a 2008 dodge avenger, after I finished making oil change the engine light went on. What would it be the probvlem?


The oil change light is usually mileage related, and just needs to be reset. It does not know if oil was actually changed or not. Check your owners manual, or stop by a quick lube place for directions on how to reset it. This is not a problem.

Dec 12, 2010 | 2008 Dodge Avenger

1 Answer

How do i reset the oil change


Turn the key to the on position and press the accelerator pedal to the floor and back up again three times very slowly. Repeat if needed. Of course this is done when the engine is NOT running.

Nov 23, 2010 | 2009 Dodge Avenger

1 Answer

How do you shut change oil display after changing oil on dodge avenger


if you change your own oil, try taking off the negative wire and turn the key on and off several times. otherwise you have to take it to a mechanic to reset the codes. you can also try resetting your mileage to service

May 11, 2010 | 2008 Dodge Avenger

1 Answer

I have a 98 Dodge avenger ES,,, After im driving


could be a pluged oil filter or falty oil sending unit did you try changing your oil

Mar 18, 2010 | 2008 Dodge Avenger

2 Answers

Reset oil change for a 2008 dodge aveneger


To reset your maintenance reminder system (even if the light hasn’t come on yet), you’ll need to turn your key to on (but don’t start!) and make sure your odometer is on TRIP A. Then key off. Press and hold the Odometer/Trip button. While holding down on the button, key the ignition to on (Don’t start the engine!) The display panel will count down from “------“ to “-“Continue pressing the button until the Trip A is displayed. After this step, you are done.

Oct 21, 2009 | 2008 Dodge Avenger

1 Answer

How do I get the "Change Oil " light to go off after change .


Turn key to the run posistion and pump the gas peadle 3 times under 5 seconds.

Jul 18, 2009 | 2008 Dodge Avenger

Not finding what you are looking for?
2009 Dodge Avenger Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...