Question about Cars & Trucks

Open Question

Picture location camshaft position sensor-05 3400

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 50 Answers

SOURCE: I cant find a detailed picture of where the location is to check these items.

The crankshaft position sensor is located on the transmission bell housing on the right side (if you're facing the engine from the transmission side). The camshaft position sensor is towards the top center of the timing cover on the front of the motor. They both have 3 wire connectors that are virtually identical.

Posted on Apr 18, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

  • 14036 Answers

SOURCE: 98 silverado 5.7L camshaft position sensor

ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Posted on Oct 23, 2009

  • 85 Answers

SOURCE: Where is the camshaft position sensor on a 2000 Ford Explorer?

in the rear like where the dist would normaly be

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft position sensor located on a 2005 cadillac deville base model?


LOCATION
The camshaft position sensor is located on the rear cylinder bank in front of the exhaust camshaft. The camshaft position sensor extends into the rear cylinder head and is sealed with an O-ring.


26349435-oucqd2i3pucu3s1utbyq1gmo-1-0.gif

Nov 10, 2016 | 2005 Cadillac Deville

1 Answer

What is location of crankshaft position sensor on 2007 ford f250 with 6.0 diesel.


There are some GREAT pictures I think will help you find it. Go to http://www.ford-trucks.com/forums/1160636-camshaft-position-sensor-cmp-wiring-pigtail-replacement.html It is located under the subject of "Camshaft Position Sensor (CMP) wiring pigtail replacement"

Feb 28, 2015 | Ford Cars & Trucks

1 Answer

Where is the camshaft position sensor located in a


The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Oct 10, 2014 | Cars & Trucks

2 Answers

Where is 2003 ford focus camshafts position sensor


Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor

a452a319-2d08-4e59-9885-fe43b5fc7f61.gif

and next the location of 2003 ford focus camshafts position sensor
96d62950-03fc-4668-b3ad-dfa939f76b14.gif

Sep 13, 2014 | 2003 Ford Focus

2 Answers

The camshaft position sensor is bad but I don't know where it is located or how to change it


it depends on the vehicle. and you did not say what type of vehicle. most general motors C/S sensors are located at the front of the engine above the timing chain cover . some are located on the Rt. sice of the cylinder head

Apr 18, 2013 | Cars & Trucks

1 Answer

Code P0340 appears on my scanner and tells me it is the camshaft sensor or sensors. I am trying to find the location of the camshaft sensors so I can determin if I can try to replace them myself. I need...


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


Fig. 1 Camshaft Position Sensor - 2.4L DOHC 92769810
The camshaft position sensor is mounted to the rear of the cylinder head.

Jan 02, 2011 | 2002 Chrysler PT Cruiser

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

I cant find a detailed picture of where the location is to check these items.


The crankshaft position sensor is located on the transmission bell housing on the right side (if you're facing the engine from the transmission side). The camshaft position sensor is towards the top center of the timing cover on the front of the motor. They both have 3 wire connectors that are virtually identical.

Apr 17, 2009 | Plymouth Grand Voyager Cars & Trucks

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

3 Answers

Camshaft Poaition Sensor


a picture is worth 1000 words if ya need more help let me know5a5f7cf.jpg684e6e1.jpg

Aug 24, 2008 | 1999 BMW 7 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...