Question about 2004 Ford F350

1 Answer

Dtc trouble code po000 - 2004 Ford F350

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

P0000 is given if a code is unrecognized and the U code is missing a digit.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Feb 10, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What are the probable causes of DTC P0720?


According to the database the code means OUTPUT SPEED SENSOR CIRCUT MALFUNCTION.

Dec 12, 2015 | Cars & Trucks

Tip

Obd-ii error codes


OBD-II (Check Engine Light) Trouble Codes Welcome to OBD-Codes.com, your headquarters for everything OBD-II related. For more information on what OBD codes are, OBD-II codes explained, explanation of fuel trims, or answers to other questions, visit our FAQ area. The most common OBD-II codes are P0xxx powertrain codes, which are listed below on this page, along with P2xxx generic & P3xxx generic codes (please scroll down). For the other OBD-II codes, choose from Bxxxx - B Codes - OBD-II Body Codes or Cxxxx - C Codes - Chassis Codes, and Uxxxx - U - Network Codes. If your DTC (diagnostic trouble code) begins with P1xxx, that means it's a manufacturer specific code. For more information on P1 codes, choose your vehicle make here: Acura Audi BMW Chevrolet Dodge / Chrysler / Jeep Ford Honda Hyundai Infiniti Isuzu Jaguar Kia Land Rover Lexus Mazda Mitsubishi Nissan Subaru Toyota VW

Please use our new & improved search engine to find information on your trouble codes. Search Now! This list contains standard diagnostic trouble codes (DTC's) that are used by some manufacturers to identify vehicle problems. The codes provide below are generic codes that may not apply to all vehicles. Vehicle manufacturers may use manufacturer specific DTC codes that are different from the codes shown below. Foreign vehicles may also use DTC codes different from the generic DTC codes. We recommend that you not depend on the DTC codes in this list for vehicle repairs until you confirm the generic DTC codes apply to your vehicle(s). The list below is for information purposes only and is not intended for use in vehicle repairs.

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

on Apr 14, 2015 | Cars & Trucks

1 Answer

What does no dtc code on a 2001 Nissan pathfinder mean


DTC = Diagnostic Trouble Code.
No DTC means no trouble.

Feb 18, 2015 | 2001 Nissan Pathfinder

1 Answer

Where is the obd2 connector location on holden ra rodeo v6


isuzimpuls.gif
Connect white (test lead) and black (ground lead) wires that are branched from harness approximately eight inches from ECM. After leads are grounded, the "Check Engine" light will flash the diagnostic trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.I-MARK 84-85
Connect male and female test leads taped into wire harness near ECM. After leads are connected, the "Check Engine" lamp will flash the trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.
86-87 Impulse located near the ECM connector, is used to actuate the Engine Control Module (ECM) trouble code memory within the module. Two terminals (A and C) of this connector are used to activate the diagnostic trouble code system in the ECM. With the ignition switch turned On, engine Off, connect a jumper wire between terminals A and C. The "Check Engine" lamp will begin by flashing a DTC 12. DTC 12 = flash, pause, flash, flash. There will be a longer pause and a code 12 will repeat two more times. This code indicates the self-diagnostic system is operating. The cycle will then repeat until the engine is started or the ignition is switched Off. In most cases, DTC's will be checked with the engine running since no DTC's other than DTC 12 or 51 will be present without the engine running. Remove jumper wire from ALDL connector before starting engine. Reconnect jumper wire after engine is running.

Throttle Body Fuel Injection

The ECM test connection is located under the center console.
A built-in, self diagnostic system will identify problems in the throttle body fuel injection system. When a problem is detected, the diagnostic system will illuminate the "Check Engine" light.
When the engine is started, the Check Engine light should turn off.. If the light remains lit, the self diagnostic has detected a problem. To determine where the problem exists, ground the "Test" terminal of the connector with the ignition On, engine Off and watch the check engine light. Each DTC will flash three times (lowest to highest).

Aug 21, 2014 | Holden Rodeo Cars & Trucks

2 Answers

What is DTC mean


Diagnostic Trouble Code- the codes the computer stores in memory when it senses a malfunction or aberration of sensor information. there are hundreds of possible trouble codes.

I hope that's the DTC you meant. Manufacturers use all kinds of such 3 or 4 letter symbols to denote a system. Last best chance is to "google it".

May 06, 2014 | 2002 Acura 3.2TL

2 Answers

What is dtc?


This means Diagnostic Truoble Codes;

A DTC is made up of 5 digits. The figure below demonstrates the composition of a DTC. With this information it is easier to trouble shoot a DTC without knowing the description of the code.


8_14_2012_6_35_17_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 14, 2012 | 2002 Mitsubishi Montero

1 Answer

What is service engine light code 12 mean



READING CODES USING MIL (CHECK ENGINE) LAMP

Be advised that the MIL or CHECK ENGINE light can only perform a limited number of functions and it is a good idea to have the system checked with a scan tool to double check the circuit function.

  1. Within a period of 5 seconds, cycle the ignition key ON - OFF - ON - OFF - ON .
  2. Count the number of times the MIL (check engine lamp) on the instrument panel flashes on and off.

The number of flashes represents the trouble code. There is a short pause between the flashes representing the 1st and 2nd digits of the code. Longer pauses are used to separate individual 2-digit trouble codes.
An example of a flashed DTC is as follows:


Lamp flashes 4 times, pauses, then flashes 6 more times. This denotes a DTC number 46. Lamp flashes 5 times, pauses, then flashes 5 more times. This indicates a DTC number 55. DTC 55 will always be the last code to be displayed.


0900c1528007935b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Diagnostic trouble code chart (1 of 2)-1995-97 engines


0900c1528007935c.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Diagnostic trouble code chart (2 of 2)-1995-97 2.0L engines

Jul 26, 2012 | 1995 Dodge Neon

1 Answer

How do you reset the security light on a 2005 chevy cobalt?


There is no reset , if security light is lit there is a problem with the anti-theft system .Should have it checked for DTC'S - diagnostic trouble codes . Could have 8 different B - codes
DTC B0685 DTC B2955 DTC B2960 DTC B3031 DTC B3033 DTC P1626 DTC P1630 DTC P1631
You would need a professional type scan tool to read these type codes , not an OBD 2 code reader .

Apr 14, 2012 | Cars & Trucks

1 Answer

2002 Buick LeSabre ECM DTC codes


P14xx and P15xx Diagnostic Trouble Codes?????????? You say has no DTC'S ???? What ?????

006 O2 Sensor Signal Analysis
What are the fuel trims at ? add fuel ,taking it away . Are the O2 sensors switching ?
What does scan data show the mass air flow sensor doing ?
010 Mass Air Flow Signal Analysis

006 Fuel Pump Current Testing Fuel pressure is AOK ??? fuel flow ?

035 Emission Tests Lean Fuel Condition

002 Fuel System Tests Start Here
DTC P1404
DTC P1441
DTC P1635
DTC P1639
DTC P1640
DTC P1650
DTC P1660
DTC P1670




Jul 24, 2017 | 2002 Buick Rendezvous

Not finding what you are looking for?
2004 Ford F350 Logo

Related Topics:

468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...