Question about Chevrolet Aveo 5

Open Question

How the timing belt mark for chevrolet captiva 2.0 diesel turbo?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: 1999 kia sportage timing marks

dfd3ea1.gif Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif

  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
  8. NOTE: Replace tensioner spring if timing belt deflection is excessive.
Timing Belt Installation


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Posted on Jul 26, 2009

Ad
TDISLine
  • 1874 Answers

SOURCE: 1999 Ford Transit Turbo Diesel

The timing marks diagram for 1999 Ford Transit Turbo Diesel 2.5 TD, 85 kW, (116 BHP) "4ED" engine code:

tdisline_143.jpg

Posted on Jan 06, 2011

Murphybanton
  • 2004 Answers

SOURCE: i what to remove the inner door panel on a Chevrolet Captiva

Check above your head. Where the light comes on. Switch to off (i.e. Middle)

Posted on Mar 18, 2009

Technopro
  • 243 Answers

SOURCE: timing marks for 86 diesel pajero

I can send you the timing marks and procedures. Email me: technopro@windowslive.com
Cheers.
Give me the engine number...4D55 or 4D56 Turbo/Non turbo.
Cheers

Posted on Apr 20, 2009

  • 3 Answers

SOURCE: 2006 volkswagon timing belt jetta tdi turbo diesel

Hey spend the extra cash and go direct to VW web site, most manufactures offer online manuals for a small fee. well worth it, especially on newer timing belts. its not your old 85 toyota. good luck

Posted on May 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevrolet captiva ltz turbo diesel cranking but wont start problems related


problems include
insufficient cranking speed
incorrect fuel pump pressure to the injectors---25,000 psi--
crank position sensor problem
glo-plugs inoperative
air in the fuel system
fuel tank not venting
ECM problems

run the fault codes to find the area of the failure

Dec 28, 2016 | Chevrolet Captiva Cars & Trucks

1 Answer

Timing belt mark of chevrolet captiva


Cam shaft and harmonic balancer have marks like a - or a .

Aug 31, 2014 | 2007 Chevrolet Captiva 2.0

1 Answer

Timing belt marks for w reg seat alhambra diesel turbo:-)


Camshaft setting tool put in position(rocker cover off) pump locking tool inserted, top dead center mark on flywheel in correct position.if not correct something won't line up

Jul 06, 2014 | 2005 Seat Alhambra 1.8

1 Answer

Chevy troubleshooting


I have 2008 Chevrolet captiva 2lt diesel it now has very low power 1000-to-2000 revs after 2000 turbo come in to play and all ok what is this and how c I fix it

Jan 04, 2014 | Cars & Trucks

1 Answer

Captiva timing


where is the yaw rate sensor on a chevroler captiva 2009

May 08, 2013 | 2009 Chevrolet Captiva 2.0

1 Answer

Holden timing marks for 2.8 diesel turbo 1999 rodeo pictures of timing gears and marks please


hi i got a izuzu holden 2.8 turbo diesel gear timming i need a pic of timming marks pls i put in new diesel pump

Oct 05, 2011 | Cars & Trucks

1 Answer

Timing marks trooper 1985 mod dlx turbo diesel


Refer to Figures 1,2,3,4 when performing 17-step timing procedure for 1981-1985 Diesel Engines.

Fig 1. Injection pump and camshaft alignment marks - Diesel engine.

archaeology_66.jpg


Fig 2. Removing the timing belt holder - Diesel engine.

archaeology_67.jpg

Fig 3. Injection pump alignment marks - Diesel engine.

archaeology_68.jpg

Fig 4. Tensioiner Pulley Bolt Sequence - Diesel engine.

archaeology_69.jpg

Procedure - Timing Belt replacement.

1. Disconnect the negative battery cable. Drain the cooling system.

CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

2. Remove the timing belt cover. Remove the injection pump sprocket flange.

3. Using a prybar, remove the tension spring from the timing belt tensioner.

When removing the tension spring, avoid using excessive force for the spring may become distorted.

4. Remove the tensioner pulley bolt and the pulley.

5. Remove the timing belt and discard it.

To install:

6. Rotate the crankshaft to bring the No. 1 piston to TDC of the compression stroke.

7. Align the timing marks on the injection pump sprocket with the camshaft sprocket; the marks must be facing each other.

8. Using a new timing belt, install it in the following sequence: crankshaft sprocket, camshaft sprocket and the injection pump sprocket; the slack must be between the injection pump and camshaft sprockets.

9. Install the tension center and the tension pulley so the end of the tension center is fitted against both pins on the timing pulley housing.

10. Hand tighten the nut so the tension pulley can be rotated freely.

11. Install the tension spring and semi-tighten the pulley nut to 22-36 ft. lbs. (30-48 Nm).

12. Rotate the crankshaft 2 full turns clockwise to seat the belt and further turn the crankshaft 90° beyond TDC to settle the injection pump.

13. Loosen the tension pulley nut to take up the timing belt slack. Tighten the tension pulley nut to 79-94 ft. lbs. (108-128 Nm).

14. Install the injection pump sprocket flange; the hole in the outer circumference of the flange should be aligned with the triangular timing mark on the injection pump sprocket.

15. Rotate the crankshaft 2 full turns clockwise to bring the No. 1 piston to TDC of the compression stroke. Make sure the triangular timing mark on the timing sprocket is aligned with the hole in the flange, then, measure the timing belt tension; it should be 33-55 lbs.

16. Install the timing belt cover.

17. Connect the negative battery cable.

Jul 04, 2011 | 1995 Isuzu Trooper

1 Answer

Timing marks for 86 diesel pajero


I can send you the timing marks and procedures. Email me: technopro@windowslive.com
Cheers.
Give me the engine number...4D55 or 4D56 Turbo/Non turbo.
Cheers

Apr 20, 2009 | Mitsubishi Passenger Cars & Trucks

1 Answer

Need the timing marks for a 3.1 td 5 cyl diesel injection pump


isusu engine?? have you looked for a 8mm hole in timing gear that corresponds with a hole on plate behind then lock it in with a bolt ,remove bolt after tightening belt .DONT FORGET THIS ???.....if you cant find anything do it with no timing marks easy --- piston no 1 at tdc valves closed spin pump till fuel comes out of no 1 injector feed and lock it all together,indirect diesel is 6/8 ,,,,,direct injection is 12/16,,,,and turbo is 18/22 btdc

Dec 13, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,808 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...