Question about 2006 Ford F-250 Super Duty

1 Answer

Fordf250 super duty metal shavings in primary fuel filter ,won't start 6.0 liter power stroke 148000 thousand miles

I have had the truck since it was new it cold starts rough idle when it warms up it runs fine until a few days ago I changed the primary and secondary fuel filters and found fine shavings on the primary filter only a few days later it would not start cranks but won't start

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,797 Answers

THE SHAVINGS ARE FROM THE FUEL PUMP ROTOR, REPLACE THE FUEL PUMP INSIDE THE GAS TANK.

Posted on Feb 09, 2012

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: 1999 Ford F-250 Super Duty 6.8 liter v10 is

You'll have to drain system down when cooled off, remove any brackets in your way such as power steering reservoir holding bracket, then remove 2 bolts holding the housing, and remove it. Rad hose should be o.k. to leave on, but if it creates a problem, remove it as well. I'd install a new thermostat and "o" ring complete,then a new gasket as well. Clean all surfaces well before re-installing. Replace any bracket(s) you removed to access housing, after housing is installed. Remember, air valve on edge of thermostat goes in 3 oclock position when re-installed. Also a reminder as well, spring on thermostat goes down when re-installed. After all is re-assembled, re-fill coolant and start engine and run with heater on to bleed out all air. Leave rad cap off and pay attention to temperature gauge and when you see it getting to normal operating temperature, watch flow in rad for increased flow, indicating thermostat opened and coolant is circulating properly. Wait until you see that flow increase 2 or 3 times, and air should be out of system, and top up coolant in rad, put cap back on, and check that return bottle is at proper level as well. Keep an eye for any leaks, and re-check return bottle periodically for first little while, just to be sure all is good. Note: some only use the "O" ring as a seal, and no gasket is required, but just check that at autoparts place where you get part.

Posted on Dec 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I fix a no start issue? cranks but won't start


Uh oh, you may have had to bleed the air out of the fuel system after the filter change. You may damage the fuel pump ($$$$$) by cranking the engine with no fuel to lube the very high pressure fuel pump. It started a few times because there was still fuel in the pump. Now it's dry.

May 13, 2014 | 2010 Ford F-250 Super Duty

2 Answers

Why does my super duty f 250 run rough when cold now it wont start at all


now it wont as in its not cold now? When its cold you get more fuel kinda like a choke if you will being a power stroke they love cold air.
so its normal it should run like that tell it gets warm let it idel for a couple min.

Feb 27, 2014 | 2006 Ford F-250 Super Duty

1 Answer

Ford 2001 f250 v10, ran out of gas, filled tank and still won't start


check for fuel pressure at fuel rail if no pressure or low pressure check and change fuel filter while ya have it off or it could be relay switch that would be the least expensive place to start good luck

Oct 15, 2011 | 2001 Ford F250 Super Duty Super Cab

1 Answer

Truck will not start


I think there is an electric fuel pump to supply fuel to the injection system. I would check into that part of the system.

Oct 14, 2009 | 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

How do i change the fuel fitler in a 03 power


should have a cover on top of the engine, lift cover , there will be a cylindrical Fuel Filter housing with a lever on the side and a cap on top. remove the cap, remove the old filter & install the new filter & the NEW seals. use the little lever to drain the old fuel & any water from the fitler housing & start engine per normal Diesel starting procedures

Oct 08, 2009 | 2003 Ford F Super Duty Chassis Cab

1 Answer

2005 Ford F250 Diesal Pickup, 6.0 liter I drove the Truck into the shop and it was running fine.I changed the oil cooler because of oil in the cooling system. I put everthing back together started the...


The primary pump is defective, it has a check valve that is bad so replace the pump it costs $0.00 compared tothe pressure pump thats $900.00 and it will be damaged if let run dry.

Jul 29, 2009 | 2005 Ford F 350 Super Duty

1 Answer

2001 F250 power stroke 7.3 liter turns over but won't start


did it start up easily right away?
Has it happened more than once?

Apr 15, 2009 | 2001 Ford F250 Super Duty Super Cab

Not finding what you are looking for?
2006 Ford F-250 Super Duty Logo

327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...