Question about 2000 Ford Taurus

Open Question

Remove ignition switch without key ford taurus

Remove key cylinder ignition

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

leetamara
  • 702 Answers

SOURCE: ford taurus 1996

Place key in ign. lock n tumbler and turn to "on" position. Under the column you'll see a small hole to put a small screwdriver or rod into and press it in. While you're pressing it, pull the lock n tumbler out. Installation is the reverse of removal but without the use of the rod. Just push the lock n tumbler in the hole and turn key to lock position and pull key out.

Posted on Jul 28, 2008

Richie_asg1
  • 1036 Answers

SOURCE: Ignition switch 84 Ford F150 no key

Hi,
When you say you were able to remove it - does this mean the broken part of the key? if it was, then just take both pieces to a locksmith that cuts auto keys, and have a replacement cut. If it uses a transponder, make sure this is copied also.

With a working key, remove any plastic surround around the lock mechanism (put the steering wheel back on), and look at the lock mechanism around the actual lock. Turn the key to position 1. This should allow a small pin on the side of the lock body to be pressed in - releasing the lock cylinder, which will come out on the key when you pull it.

These are some makes where you have to drill to depress the catch, but this is a hands-on job for an auto locksmith.

Hope this helps.

Thanks for using Fixya.

Posted on Dec 26, 2008

  • 1 Answer

SOURCE: ignition switch in a 1995 ford taurus

my 1995 taurus dont start i change the fual pump and filter also ignition control mod what else could it be

Posted on Feb 05, 2009

  • 1 Answer

SOURCE: stuck ignition cylinder 1992 ford taurus

It is not necessary to have the dealer do this, think of the cash! Though it does require patience and time. The pin you are supposed to push in goes into a slot when you have it in run position, since you cannot turn it to run you have to make a slot for the pin to go into, with a drill. Be very careful as you only have a 1/4" of play before you break a washer behind the cylinder. Once you have drilled out the key far enough to the pin hole you can take a nail set and tap the pin up, you can tell when the pin clears the housing, then it just takes wiggle, patience and tinkering to get the cylinder to slide out, keep the green washer and the metal slot washer. Metal slot washer goes in first with green plastic washer ontop of that with lock cylinder in last. You can play around with the new lock cylinder and washer before insertion to determin correct direction.

Here are official directions with inoperable lock cylinder. They say drill out retaining pin but it just spun in circles for me - I looked at new cylinder and saw how it worked. retaining pin needs a place to go.
Removal & Installation (Non-Functional)
NOTE:Use this procedure to remove ignition lock cylinder if key is missing or cylinder is frozen.

Disconnect negative battery cable. Disable air bag system. See appropriate AIR BAG RESTRAINT SYSTEMS article in RESTRAINTS. Wait at least one minute for air bag back-up power supply to deplete. Remove steering wheel. See STEERING WHEEL . Using a 1/8" bit, drill out retaining pin located below lock cylinder on housing. DO NOT drill deeper than 1/2".
Using channel lock pliers, twist lock cylinder cap until it separates from lock cylinder. Using a 3/8" drill bit, drill down center of ignition lock key slot about 1 3/4" until lock cylinder breaks loose from its base.
Remove retainer, washer, and lock cylinder gear from housing. Remove metal shavings from lock cylinder bore. Replace housing if damaged. To install, reverse removal procedure. Connect negative battery cable. Check air bag system for proper system operation. See appropriate AIR BAG RESTRAINT SYSTEMS article in RESTRAINTS.

Posted on Jul 12, 2009

  • 1024 Answers

SOURCE: how to remove an ignition lock cylinder on 1991

hard! there is a hole on the steering column near the lock cylinder. normally you can turn the key and stick a small screw driver in it to pull out the lock cylinder. in this case you can drill the pin through that hole then pull it out

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 ford taurus key won't turn ignition


The steering wheel was turned when the key was removed. So when you try to turn on the key, turn the wheel one way and the other way to release the pressure on the key. The key should turn ok.
Hope this helps.

Jul 29, 2012 | 2001 Ford Taurus

1 Answer

Where abouts is the igbition switch located on a ford taurus 1996


Inspect/Test/Replace The ignition switch is usually mounted to the steering column and is operated by a linkage rod.
NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.
f32-17gif.gif The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch:
  • Remove the ignition switch wiring harness.
  • Unbolt it from its position.
  • Bolt the new switch into position.
  • Attach the witing harness.

May 20, 2012 | 1996 Ford Taurus

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

All my key does is spin back and forth and will not start the car, feels like it is not catching anything at all. could this be the ignition lock cylinder gone bad or something else? Thank you in...


Hi:
The problem is either your ignition switch, or the mechanical linkage connecting it to the lock cylinder. Often there is a small part that can break and cause your switch not to turn. Usually you can remove the electrical switch from the lock cylinder and replace it , but be carefull working in the area around the drivers air bag!

Apr 21, 2010 | 1996 Ford Taurus

2 Answers

Car still running after take key out . cheked barrel thats ok don't know if it's relay problem


I think you have a bad ignition switch, not the ignition lock cylinder. they are 2 different things.

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.

Nov 21, 2009 | 1996 Ford Taurus

1 Answer

How can i reprogram a new ignition switch cylinder?


Well sorry to tell you if you have a PATS key for your ignition you will have to take it to your Ford dealer to get your keys programmed. My advise to you is just to get 1 key programmed then tape it to your steering column and get regular keys from the hardware store cut to fit your ignition that way if you misplace it it only costs you $2.00 to get a new 1 made.

Apr 17, 2009 | 2006 Ford Taurus

1 Answer

New Ignition Cylinder doesnt click in?


Lock Cylinder Functional
Removal
  1. NOTE: The following procedure applies to vehicles that have functional ignition switch lock cylinders (11582), lock cylinder keys are available for these vehicles or the lock cylinder key numbers are known and the proper key can be made.

    Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Turn ignition switch lock cylinder to RUN position.
  1. Place a 3.17 mm (1/8-inch) diameter wire pin or small drift punch in hole in lower steering column shroud (3530) under ignition switch (11572). Press retaining pin while pulling out on ignition switch lock cylinder to remove it from steering column lock cylinder housing (3511).
Installation
  1. Install ignition switch lock cylinder by turning it to RUN position. Insert ignition switch lock cylinder into steering column lock cylinder housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning ignition switch lock cylinder to OFF position. This will permit cylinder retaining pin to extend into steering column tube flange hole.
  1. Rotate ignition switch lock cylinder, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.

Apr 03, 2009 | 1995 Ford Taurus

2 Answers

Ignition switch in a 1995 ford taurus


Ignition Lock Cylinder
Ford Taurus/Sable 1986-1995 Repair Information grey_line.gif

clearpixel_002.gif clearpixel_002.gif lower_right.gif

clearpixel_002.gif

REMOVAL & INSTALLATION

Functional Lock


The following procedure applies to vehicles that have functional lock cylinders. Such cylinders either have a key available or known key numbers from which a key can be made.
  1. Disconnect the negative battery cable.
  2. Turn the lock cylinder key to the RUN position.
  3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

Using the key, turn the ignition lock cylinder to the RUN position, then depress the retaining pin using a wire pin or small drift

To install:
  1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
  2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
  3. Connect the negative battery cable.

Non-Functional Lock
The following procedure applies to vehicles in which the ignition lock is inoperative and the lock cylinder cannot be rotated due to a lost or broken key, unknown key number or a lock cylinder cap that has been damaged and/or broken to the extent that the lock cylinder cannot be rotated.

Jan 27, 2009 | 1995 Ford Taurus

1 Answer

Repair ignition in a 1996 Ford Taurus


You need to replace the ignition lock cylinder and/or the ignition switch actuator parts that turn the electrical switch off,on,start when the key is turned, the electrical part of the ignition is remote from the lock cylinder, it is operated by a gears and a rod.

Aug 01, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
2000 Ford Taurus Logo

Related Topics:

861 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...