Question about 1998 GMC Suburban

1 Answer

My left tail light and turn light not working on 1998 gmc suburban. Bulb is fine.

I had bulb replaced but still not working.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • GMC Master
  • 5,332 Answers

Sounds like you have a bad tail light circuit board.

unplug the connector and use a test light to confirm there is power to the circuit board for the lights that do not work. If there is power replace the circuit board. They are usually in stock at your local parts store.

Posted on Feb 09, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2008 gmc acadia low beam light bulb changing

how do you change the low beam light bulb on the 2008 gmc acadia

Posted on Apr 02, 2009

  • 59 Answers

SOURCE: headlight replacement 1998 GMC Sierra

there are two rods that slide down from the top. you have to turn to get them out of clip then pull up. once both are out then headlight can be removed.

Posted on Dec 22, 2008

  • 1 Answer

SOURCE: Replace 2005 GMC Sierra Daytime Running Lights...

Open the hood, and in the top right and left corners of the primary headlamps you'll see two pins (L shaped) swing them out (towards the front of the truck) and lift out. This allows you to remove the upper headlamp assembly. You can then remove the lower assembly by pushing outwards on the plastic clip that is hooked into a metal clip. Once it's out you just turn the bulb to remove it.

It's much easier if you unhook the leads to the upper assembly's bulbes so you can set the whole thing aside.

Posted on Mar 31, 2009

  • 1986 Answers

SOURCE: My turn signals and brake lights are not working.

Does your high mount stop light work? If it doesn't, then it'll be the brake switch located just above your brake pedal.

If the light does work, then it should be the electronic flasher module that will be located under your dash near the steering column. It will be labeled. This controls your signals, but I believe your brake lights are also on the same bulb as your signals, so when this goes, it can affect your brake lights

Posted on Oct 14, 2009

  • 14 Answers

SOURCE: how do i replace the tail light bulb?

to replace the GM tail light bulb, you will drop down the tail gate and you will notice 2 screws on the tail light assembly, you will remove those 2 screws with the proper screw driver, once you do that the whole tail light assembly will come off, then you will see onother 2 screws holding the light panel to the tail light assembly, or brackets holding the light panel to the tail light assembly remove either or and you will have access to the three bulbs on that light panel, replace the burnt one and follow the same intrunctions to put back.

Posted on Apr 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I take off the tail light assembly to replace the bulb for the left tu


Open the trunk. In the left corner where the lamp assembly is, you should see two screw covers that cover the screws holding in the lamp assembly.

12_5_2012_6_45_21_pm.jpg

Remove these covers to find the screws, and unscrew them to pull the taillamp assembly out of the vehicle body. Disconnect the lamp wiring harness, turn the bulb socket counterclockwise to pull out the socket, revealing the light bulb. Then pull the bulb right out of the socket and replace it with a new bulb.

Replace the socket, turning it clockwise. Replace the taillight assembly. Check that the taillamp assembly tab, located at the bottom of the taillamp assembly, is aligned to the facia bracket before securing the screws.
12_5_2012_6_46_06_pm.jpg


Screw the taillamp assembly back into the vehicle body and replace the screw covers. Check to make sure the new bulb works properly.

Your owners manual specifies that the rear left turn lamp is a lamp with bulb number 3057K. You should be able to find them at any automotive store or from your dealer. Hope this helps.

Dec 05, 2012 | 2011 GMC Terrain

1 Answer

1991 gmc suburban right tail light won't work


Check the socket for power (with a 12 volt test light probe) to the pin that operates the running light bulb filiment, use the other tailight for a guide or just touch all the pins, one should light the test light up

Sep 06, 2012 | 1991 GMC Suburban

1 Answer

Break light on my 1998 gmc suburban does not work


Does the third brake light work?
If it does the get a test light and check the circuit inside the brake light. it can be the circuit board or the pig tail the not getting connection.

Jun 05, 2012 | 1998 GMC Suburban

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

1 Answer

1999 GMC Suburban, K1500 4WD. Top brake light bar


third light is different circuit. saftey reason check fuses grounds wires

Oct 10, 2009 | 1999 GMC Suburban

2 Answers

Right brake light out; tail light works fine


most rear tail lights and turn/stop lights are the same dual filiment bulb. it is possible for your tail light to work and your brake light not to and still have a bad bulb. I would check the bulb first, your brake light works on the left yes? this would mean that the fuse is fine

Mar 31, 2009 | 2006 Dodge Stratus

1 Answer

How do i fix my GMC suburban tail lights?


Did you check all three fuse boxes? Does your instrument cluster still work?

Dec 29, 2008 | 1998 GMC Jimmy

1 Answer

License Plate lamp burned out.


you'll see the lights plugged in under rear bmper. grasp the light plug,twist counter clkwise 1/4 turn, pull out plug, pull bulb strait out, push new bulb back in.

Nov 11, 2008 | 1998 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...