Question about 1998 Mazda 626

Open Question

P1409 EGR Vacuum Regulator Solenoid Circuit

P1409

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ZJLimited
  • 17970 Answers

SOURCE: P1409

DTC P1409: MEASURE RESISTANCE ACROSS EGR VACUUM REGULATOR SOLENOID
Diagnostic Trouble Code (DTC) P1409 indicates that Self-Test has detected an electrical fault in the EVR circuit.

Possible causes:

Open EVR circuit.
Open VPWR circuit to EGR Vacuum Regulator solenoid.
EVR circuit shorted to VPWR.
EVR circuit shorted to GND.
Damaged EGR Vacuum Regulator solenoid.
Damaged PCM.
Key off.
Disconnect EGR Vacuum Regulator solenoid.
Measure EGR Vacuum Regulator solenoid resistance.
Is solenoid resistance between 26 and 40 ohms?
Yes No
The EGR Vacuum Regulator solenoid resistance is within specification. GO to HE111 . REPLACE EGR Vacuum Regulator solenoid. RECONNECT all components. COMPLETE PCM Reset to clear DTCs. RERUN Quick Test.

HE111 CHECK VPWR CIRCUIT VOLTAGE AT EGR VACUUM REGULATOR SOLENOID
Key on, engine off.
EGR Vacuum Regulator solenoid disconnected.
Measure voltage between VPWR circuit at the EGR Vacuum Regulator solenoid vehicle harness connector and chassis GND.
Is voltage greater than 10.5 volts?
Yes No
GO to HE112 . SERVICE open in VPWR circuit to EGR Vacuum Regulator solenoid. RECONNECT all components. COMPLETE PCM Reset to clear DTCs. RERUN Quick Test.

HE112 CHECK EVR CIRCUIT RESISTANCE
Key off.
EGR Vacuum Regulator solenoid disconnected.
Disconnect PCM. Inspect for damaged or pushed out pins, corrosion, loose wires. Service as necessary.
Install breakout box and leave PCM disconnected.
Measure resistance between Test Pin 47 (EVR) and EVR circuit at the EGR Vacuum Regulator solenoid vehicle harness connector.
Is resistance less than 5.0 ohms?
Yes No
GO to HE113 . SERVICE open in EVR circuit. RECONNECT all components. RERUN Quick Test.

HE113 CHECK EVR CIRCUIT FOR SHORTS TO POWER OR GROUND
Key off.
EGR Vacuum Regulator solenoid disconnected.
Breakout box installed, leave PCM disconnected.
Measure resistance between Test Pin 47 (EVR) and Test Pins 71 and 97 (VPWR) at the breakout box.
Measure resistance between Test Pin 47 (EVR) and Test Pins 24 and 103 (PWR GND) at the breakout box.
Is each resistance greater than 10,000 ohms?
Yes No
REPLACE damaged PCM. RECONNECT all components. RERUN Quick Test. SERVICE EVR circuit for short to VPWR or PWR GND. RECONNECT all components. RERUN Quick Test.

HE120 CONTINUOUS MEMORY DTC P1409: WIGGLE EGR VACUUM REGULATOR SOLENOID WHILE MONITORING VPWR
Continuous Memory DTC P1409 indicates that Continuous Memory Self-Test has detected an electrical malfunction in the EGR Vacuum Regulator solenoid sometime during vehicle operation.

Note: If DTC P1409 was output in Key On Engine Off (KOEO) or Key On Engine Running (KOER) Self-Test, go to HE110 to diagnose present fault.

Possible causes:

Open EVR circuit.
Open VPWR circuit to EGR Vacuum Regulator solenoid.
EVR circuit shorted to VPWR.
EVR circuit shorted to GND.
Damaged EGR Vacuum Regulator solenoid.
Damaged PCM.
Disconnect PCM. Inspect for damaged or pushed out pins, corrosion, loose wires.
Install breakout box, leave PCM disconnected.
Measure voltage between Test Pin 47 (EVR) and Test Pins 24 (PWR GND) at the breakout box.
Key on.
Voltage must read greater than 10.5 volts. For an indication of a fault, look for this voltage to drop while performing the following:
Lightly tap on the EGR Vacuum Regulator solenoid.
Wiggle the EGR Vacuum Regulator solenoid connector.
Grasp the EGR Vacuum Regulator solenoid vehicle harness connector and wiggle wires between solenoid and PCM.
Is a fault indicated?
Yes No
ISOLATE fault and SERVICE as necessary. RECONNECT all components. RERUN Quick Test. Unable to duplicate or identify fault at this time. GO to Pinpoint Test Step Z1 with the following data: DPFEGR and EGRVR PIDs and list of possible causes.

Posted on Sep 25, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code P1409


if its a ford product its --- P1409 EGR stepper motor circuit malfunction. God-Bless! if not just repost the make and year of vehicle.

Jul 12, 2016 | Cars & Trucks

1 Answer

What does code p1409 mean


"EGR Vacuum Regulator Solenoid Circuit Malfunction". Check the EGR vacuum regulator solenoid.

Aug 04, 2014 | Ford F-150 Cars & Trucks

1 Answer

P1409


check for vacuum leaks and check the vacuum regulator control unit for correct operation.

Apr 12, 2014 | 1998 Ford F250 SuperCab

1 Answer

WHAT DOES CODE P1409 MEAN ON A 1998 FORD RANGER 3.0


P1409--EGR Vacuum Regulator Solenoid Circuit Malfunction

Dec 05, 2012 | 1998 Ford Expedition

1 Answer

P1409


DTC P1409: MEASURE RESISTANCE ACROSS EGR VACUUM REGULATOR SOLENOID
Diagnostic Trouble Code (DTC) P1409 indicates that Self-Test has detected an electrical fault in the EVR circuit.

Possible causes:

Open EVR circuit.
Open VPWR circuit to EGR Vacuum Regulator solenoid.
EVR circuit shorted to VPWR.
EVR circuit shorted to GND.
Damaged EGR Vacuum Regulator solenoid.
Damaged PCM.
Key off.
Disconnect EGR Vacuum Regulator solenoid.
Measure EGR Vacuum Regulator solenoid resistance.
Is solenoid resistance between 26 and 40 ohms?
Yes No
The EGR Vacuum Regulator solenoid resistance is within specification. GO to HE111 . REPLACE EGR Vacuum Regulator solenoid. RECONNECT all components. COMPLETE PCM Reset to clear DTCs. RERUN Quick Test.

HE111 CHECK VPWR CIRCUIT VOLTAGE AT EGR VACUUM REGULATOR SOLENOID
Key on, engine off.
EGR Vacuum Regulator solenoid disconnected.
Measure voltage between VPWR circuit at the EGR Vacuum Regulator solenoid vehicle harness connector and chassis GND.
Is voltage greater than 10.5 volts?
Yes No
GO to HE112 . SERVICE open in VPWR circuit to EGR Vacuum Regulator solenoid. RECONNECT all components. COMPLETE PCM Reset to clear DTCs. RERUN Quick Test.

HE112 CHECK EVR CIRCUIT RESISTANCE
Key off.
EGR Vacuum Regulator solenoid disconnected.
Disconnect PCM. Inspect for damaged or pushed out pins, corrosion, loose wires. Service as necessary.
Install breakout box and leave PCM disconnected.
Measure resistance between Test Pin 47 (EVR) and EVR circuit at the EGR Vacuum Regulator solenoid vehicle harness connector.
Is resistance less than 5.0 ohms?
Yes No
GO to HE113 . SERVICE open in EVR circuit. RECONNECT all components. RERUN Quick Test.

HE113 CHECK EVR CIRCUIT FOR SHORTS TO POWER OR GROUND
Key off.
EGR Vacuum Regulator solenoid disconnected.
Breakout box installed, leave PCM disconnected.
Measure resistance between Test Pin 47 (EVR) and Test Pins 71 and 97 (VPWR) at the breakout box.
Measure resistance between Test Pin 47 (EVR) and Test Pins 24 and 103 (PWR GND) at the breakout box.
Is each resistance greater than 10,000 ohms?
Yes No
REPLACE damaged PCM. RECONNECT all components. RERUN Quick Test. SERVICE EVR circuit for short to VPWR or PWR GND. RECONNECT all components. RERUN Quick Test.

HE120 CONTINUOUS MEMORY DTC P1409: WIGGLE EGR VACUUM REGULATOR SOLENOID WHILE MONITORING VPWR
Continuous Memory DTC P1409 indicates that Continuous Memory Self-Test has detected an electrical malfunction in the EGR Vacuum Regulator solenoid sometime during vehicle operation.

Note: If DTC P1409 was output in Key On Engine Off (KOEO) or Key On Engine Running (KOER) Self-Test, go to HE110 to diagnose present fault.

Possible causes:

Open EVR circuit.
Open VPWR circuit to EGR Vacuum Regulator solenoid.
EVR circuit shorted to VPWR.
EVR circuit shorted to GND.
Damaged EGR Vacuum Regulator solenoid.
Damaged PCM.
Disconnect PCM. Inspect for damaged or pushed out pins, corrosion, loose wires.
Install breakout box, leave PCM disconnected.
Measure voltage between Test Pin 47 (EVR) and Test Pins 24 (PWR GND) at the breakout box.
Key on.
Voltage must read greater than 10.5 volts. For an indication of a fault, look for this voltage to drop while performing the following:
Lightly tap on the EGR Vacuum Regulator solenoid.
Wiggle the EGR Vacuum Regulator solenoid connector.
Grasp the EGR Vacuum Regulator solenoid vehicle harness connector and wiggle wires between solenoid and PCM.
Is a fault indicated?
Yes No
ISOLATE fault and SERVICE as necessary. RECONNECT all components. RERUN Quick Test. Unable to duplicate or identify fault at this time. GO to Pinpoint Test Step Z1 with the following data: DPFEGR and EGRVR PIDs and list of possible causes.

Sep 25, 2011 | 2001 Mazda Tribute

1 Answer

I have a misfire in the 4th cylinder and need new o2 sensors and im getting the p1409 code


P1409 --- EGR Vacuum Regulator Solenoid

You didn't tell us anything I can use

What about a misfire?

What Car?
What Year?
What Engine? wires or cop ignition

O2 Sensors get replaced at 100,000 miles or
when they fail or switching counts get slow

Need to know vehicle history ,current issues in datail
& who is working on it

If you going to take it to a repair shop
I'am not getting too get involved here

Jun 12, 2011 | Lincoln LS Cars & Trucks

2 Answers

Check enegine light stay s on all the time, here are the codes im getting, if someone could tell me how to fix these that would be great. p0155 p0141 p0136 p0443 p1451 p0135 p0161 p1409


P0155: O2 Sensor heater Circuit Malfunction (bank2 ) Sensor 1.

P0141: O2 Sensor heater Circuit Malfunction (bank1 ) Sensor 2.

P0135: O2 Sensor heater Circuit Malfunction (bank1,Sensor1)

P0136: O2 Sensor Circuit Low voltage (bank1) Sensor 2.

P0443 : Evaporative Emission control System Purge control valve.

P1451: Eavporative Control System Canister vent solenoid Circuit Malfunction.

P0161: O2 Sensor Circuit Low voltage (bank2,Sensor2)

P1409: Electronic Vacuum Regulator (EVR) control circuit malfunction.

change the O2 sensors first,Then check the the EGR Vacuum regulator for any Malfunction. Good luck

Jan 14, 2011 | Ford Mustang Cars & Trucks

1 Answer

I have a fail code (P1409) on my 1998 FOrd Expedition, 4.6L. Where can I get this part? Thanks, Alec


Code indicates bad EGR Vacuum Solenoid. Chilton lists possible causes below. Here's a link to the part you want. Best of luck!
Greg

http://www.rockauto.com/catalog/raframecatalog.php?carcode=1304402&parttype=4964&a=FRc1304402k943582

Possible Causes:
  • EGR VR solenoid circuit is open, or shorted to ground
  • EGR VR circuit is shorted to power or the VPWR circuit is open
  • EGR vacuum regulator solenoid is damaged or the PCM has failed

May 19, 2009 | 1998 Ford Expedition

1 Answer

P1409 code on 2002Ford F150 4.6L


P1409 - EGR Vacuum System Leak

CHECK THE EGR CONTROL SYSTEM FOR A SERIOUS VACUUM LEAK,

Mar 24, 2009 | 2002 Ford F150 Regular Cab

Not finding what you are looking for?
1998 Mazda 626 Logo

Related Topics:

839 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...