Question about 2006 Pontiac Grand Prix

Open Question

Starter wiring diagram for 2006 grand prix

Display says system charging failure i changed starter i forgot what wires go where

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Radio Wiring Diagram

Go to www.crutchfield.com.

On the bottom of the page there is a link for product support. On the next page, type "2005 Grand Prix" in the search box and hit enter. The top link shows an image and pinout on models with Monsoon sound systems, the second link for ones without.

Hope that helps! Good luck!

Posted on Jun 20, 2008

PyroPCMan
  • 405 Answers

SOURCE: diagram on a pontiac grand prix

Ignition Switch GM Century/Lumina/Grand Prix/Intrigue 1997-2000 The vehicles covered by this guide use one of two types of ignition switches:

  • A mechanical key and lock cylinder built into the steering column, that works a pull rod to actuate the separate electrical portion of the ignition switch mounted further down the steering column. For more information and replacement procedures on this type of switch, please see .
  • An instrument panel-mounted ignition switch is also used on some W-Body vehicles. To service this switch, the radio, heater & A/C control panel and the instrument cluster must be removed. All of these procedures are found elsewhere in this section.
REMOVAL & INSTALLATION
Instrument Panel-Mounted Ignition Switch
WARNING You must perform the Body Control Module (BCM) theft deterrent relearn procedure after replacement of the ignition lock cylinder. Failure to perform this relearn procedure means the BCM will not function properly. This means the vehicle will not be theft protected by the Passlock system and the engine may not crank or start. GM recommends that this procedure be performed with their Tech 2® or equivalent scan tool. An alternate relearn procedure is given at the end of this procedure.
  1. Disconnect the negative battery cable.
  2. Remove the radio assembly following the procedures found in this section.
  3. Remove the heater & A/C control head assembly following the procedures found in this section.
  4. Remove the instrument cluster assembly following the procedures found in this section.
  5. Detach the electrical connectors from the ignition switch.
  6. Insert the key and turn the ignition switch lock cylinder to the ACC position.
  7. Depress the transaxle park/lock cable retainer to release, then pull to remove the cable from the ignition switch.
NOTE You must perform the Body Control Module theft deterrent relearn procedure after replacement of the ignition lock cylinder.
  1. If it is necessary to remove the ignition lock cylinder from the ignition switch (theft damage, etc.), use the following procedure:
    1. Insert the key and turn the ignition switch lock cylinder to the ON position.
    2. Using a small flat-bladed tool, depress and hold the lock cylinder retaining tab.
    3. Using the key as an aid, pull to remove the ignition switch lock cylinder from the switch.
    4. Remove the key from the lock cylinder.
    5. Carefully pull to release the ignition switch bezel from the ignition switch lock cylinder.
  2. Remove the ignition switch bracket bolts and remove the ignition switch through the instrument panel cluster opening.
  3. Remove the bolts retaining the ignition switch to the bracket and remove the bracket.
0900c15280090fea.jpgRemoving an instrument panel-mounted ignition switch assembly—1998 Oldsmobile Intrigue shown, others similar To install:
  1. Install the ignition switch to its bracket and install the bolts. Install the ignition switch into position through the instrument panel cluster opening and install the bracket retaining bolts.
  2. If removed, install the ignition switch lock cylinder to the ignition switch using the following procedure:
    1. Recode the lock cylinder, if necessary.
    2. Align the ignition switch bezel to the tabs on the ignition switch lock cylinder and carefully press to secure in place.
    3. Insert the key and turn the ignition switch lock cylinder to the ON position.
    4. Align the ignition switch lock cylinder to the ignition switch, then press into place.
  3. Turn the key to the ACC position. Align and press into place the transaxle park/lock cable to the ignition switch. Remove the key from the switch.
  4. Attach the electrical connectors to the ignition switch.
  5. Install the instrument cluster using the procedures found in this section.
  6. Install the heater & A/C control panel using the procedures found in this section.
  7. Install the radio assembly using the procedures found in this section.
  8. Connect the negative battery cable.
  9. If the lock cylinder was removed, perform the BCM Programming/RPO Configuration procedure.
THEFT DETERENT RE-LEARN—WITHOUT TECH 1®SCAN TOOL
This procedure takes approximately 30 minutes. Make sure the battery is fully charged before proceeding.
  1. Turn the ignition switch to the OFF position.
  2. Turn the ignition switch all the way from the OFF to the START position, then leave it in the ON position. The engine will not crank.
  3. The SECURITY light should come on and stay on for at lease ten minutes.
  4. Turn the ignition switch to the OFF position for five seconds.
  5. Repeat Steps 2, 3 and 4 again for a second time.
  6. Repeat Steps 2, 3 and 4 again for a third time.
  7. Turn the ignition switch to the OFF position.
  8. Turn the ignition switch all the way to the START position. The engine should now start.

Posted on Sep 09, 2008

raycrazek
  • 106 Answers

SOURCE: Where is the fuse box on 2006 Pontiac Grand Prix

yes it will fix your cigarette lighter. open the door on the drivers side and crawl in there and look up to your left it should be right there use a flash light .. good-luck ray

Posted on Jan 16, 2009

ZJLimited
  • 17970 Answers

SOURCE: I need a diagram for changing a serpentine belt on

2006 PONTIAC GRAND PRIX - V6 3.8L
Belt Routing Diagram - Multiple Accessory (Main Drive)

cff7db4.jpg

Hope helps (remember rated this) Good luck.

Posted on Jan 15, 2010

  • 170 Answers

SOURCE: Serpentine belt routing diagram for 2006 pontiac

Follw this link, go to page #123, diagram #6-50. Good Luck. http://www.daycoproducts.com/daycoweb.nsf/cf652a4feb630ad0862571a4005ae40c/1120b6e8f406fd3e862574c000569a91/$FILE/SerpentineBeltRoutingGuide.pdf

Posted on Sep 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a wiring harness diagram for 2006 Pontiac Grand Prix base model stereo system


http://www.modifiedlife.com/2006-pontiac-grand-prix-factory-stereo-install-diagram/

May 25, 2015 | 2006 Pontiac Grand Prix

1 Answer

Hi,my name is Devin. My 2006 grand prix will not start, it will try to turn over, but wil not start. We were wondering if it is the battery, starter,or what ? On the led in the meter reading for the...


well voltage at battery should be at least 12.6 or better. with car off. with it running,at battery if alternator is doing its job. should be at least 13.8-14.2 either alternator is going. or a wiring problem. take alternator off, and go to advanced auto or auto zone. to have it tested. if its not bad. then you have a battery problem or wiring. good-luck !! with all accessories off !

Jan 22, 2011 | 2006 Pontiac Grand Prix

1 Answer

Error code keeps coming up saying charging system failure, an car wont turn over, while making a loud clicking sound


Well if charging system has failed it sounds like your battery is to low to turn over the starter motor. Give the battery a charge over night then have the system checked for a bad alternator.

Sep 19, 2010 | 2006 Pontiac Grand Prix

1 Answer

The wires on a starter on a 1994 grand prix se 3.1l


The wire to the starter that has the small eyelet connector attaches to the "S" terminal on the starter solenoid, all other wire or wires, with the larger eyelet connector should be connected along with the Pos. (+) battery cable on the main "BAT" terminal of the starter solenoid.

Apr 09, 2010 | 1994 Pontiac Grand Prix

1 Answer

I need a diagram for changing a serpentine belt on a 2006 grand prix of some kind of information to help me with the putting the belt back on


2006 PONTIAC GRAND PRIX - V6 3.8L
Belt Routing Diagram - Multiple Accessory (Main Drive)

cff7db4.jpg

Hope helps (remember rated this) Good luck.

Jan 15, 2010 | 2006 Pontiac Grand Prix

1 Answer

Cant remember what wires go where on the starter on 97 pontiac grand prix


I WOULD SAY GET A REPAIR MANUAL TO LOOK AT THE STARTER WIRING DIAGRAM TO BE ON THE SAFE SIDE TWO RED WIRES BATTERY POSITIVE CABLE + FUSE LINK WIRE GOES TO SOLENOID POSITIVE BATTERY TERMINAL POST .THAT THE LARGE STUD WITH A BOLT.THE SMALL PURPLE WIRE GOES TO S OR SWITCH TERMINAL ON THE STARTER SOLENOID.

Sep 23, 2009 | 1997 Pontiac Grand Prix

1 Answer

THE ROMOTE STARTER WONT WORK ON MY GRAND PRIX I


the reciever might be blocked by something,dirt,a loose wire,etc.or a wire might have come loose to the starter from the remote.

Jul 22, 2009 | 2006 Pontiac Grand Prix

1 Answer

Need to view steering column diagram for grand prix 02


call gm parts department they can fax you a copy of it

Jan 25, 2009 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
2006 Pontiac Grand Prix Logo

Related Topics:

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...