Question about 1992 Ford Ranger

Open Question

WHERE'S THE OXYGEN SENSOR LOCATED ON MY 1992 FORD RANGER PICKUP WITH A 4.0 MOTOR?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 66 Answers

SOURCE: Location of the oxygen sensor

there are two O2 sensors on this engine. Both are mounted in the exhaust just past the exhaust manifolds. You will be able to replace them without a lift. You will probably need an O2 socket to remove them. They usually are in pretty tight.

Posted on Jan 04, 2009

Ajkill
  • 2035 Answers

SOURCE: 2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???

Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Posted on Jan 16, 2009

RJones1125
  • 373 Answers

SOURCE: location of oxygen sensor on 97 ford ranger

between the exhaust manifold and the catalytic converter (exhaust system)

Posted on Feb 21, 2009

the recycler
  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

bschilz
  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

7acfed1.gif
d9eb1af.gif

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1992 ford ranger 3.0 idle rough and the tail pipe is black and bad gas miles


check for clogged air filter and oxygen sensor if check eng light is on

Feb 28, 2015 | 1992 Ford Ranger

1 Answer

I have a 1992 Toyota pickup 4x4 4 cylinder. The computer set code 21 which is the oxygen sensor. I replaced the oxygen sensor and disconnected the battery to clear the code. I reconnected the battery...


The code shows oxy. Sensor , this means there is something tripping the sensor . Could be fuel delivery , catalyitic converter , or something else . .....

Jun 11, 2017 | 1992 Toyota Pickup

1 Answer

My ranger has a 4 cyl lima engine seems to run ok but has no power and burns a lot of gas could this be catalydic conerter or coil paks


It's a lot more likely to be your CAT converter. or maybe even your oxygen sensors. Do you have a service light on in your ranger?

May 20, 2011 | 1989 Ford Ranger

1 Answer

I need a fuse diagram for my 2003 ford ranger 2.3L engine


I don't know if this will help you but here are the location numbers. Can't figure out how to copy a picture of the box itself. I do have an entire owners manual I could send you as a PDF if you need it. Hope this helps. Good luck.

Description

1 50A** I/P fuse panel 2 - Not used

3 - Not used 4 - Not used

5 - Not used 6 50A** Anti-lock Brake System (ABS)

pump motor

7 30A* Powertrain Control Module (PCM)

8 20A* Power door locks, Remote entry

9 - Not used 10 - Not used

11 50A** Starter relay, Ignition switch

13 20A* 4x4 Motor 14 - Not used

15 - Not used 16 40A** Blower motor

17 20A** Auxiliary cooling fan 18 - Not used

19 - Not used 20 - Not used

21 10A* PCM memory 22 - Not used

23 20A* Fuel pump motor 24 30A* Headlamps

25 10A* A/C clutch solenoid 26 - Not used

27 - Not used 28 30A* ABS module

29 - Not used 30 15A* Trailer tow

31 20A* Foglamps, Daytime Running Lamps (DRL)

32 - Not used 33 15A* Park Lamp

34, 35, 35, 35 & 37 Not used 38 10A* Left headlamp low beam

39 & 40 Not used 41 20A* Heated oxygen sensors

Jan 28, 2011 | 2003 Ford Ranger Regular Cab

2 Answers

Where & how many oxygen sensors do I need for my 1997 Ford Ranger XLT Super Cab


Look before and after the catalytic converters. They will have wiring connected to them.

Apr 20, 2009 | 1997 Ford Ranger SuperCab

1 Answer

1997 Ford Expedition - cruise control won't work. Need a diagram for the fuse block!Help!


Vehicles involved in the recall include the following:

1998-2002 Ford Ranger
1992-1997 Lincoln Town Car
1992-1997 Ford Expedition
1992-1997 Mercury Grand Marquis
1993-1998 Lincoln Mark VIII
1993-1995 Taurus SHO
1999-2001 Ford Explorer
1999-2001 Mercury Mountaineer
2001-2002 Ford Explorer Sport
2001-2002 Ford Explorer Sport Trac
1992-1993 E150-350 Vans
1997-2002 E150-350 vans
1993 Ford F-Series pickups
1993 Ford Bronco
1994 Mercury Capri
2003-2004 Ford F0150 Lightning
1995-2002 Ford F53 motor homes.

Apr 12, 2009 | 1997 Ford Expedition

1 Answer

2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???


Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Jan 16, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

1992 ford ranger pickup 4 cyl. 5 speed


Your engine coolant temp. sensor is going bad. What happens is that your engine computer is receiving a bad signal from the ECT sensor and it thinks it's 40 below. An example is it basically slams the choke shut if it had a distributor. When it cools off, I'll bet it runs just fine.

Jul 24, 2008 | 1992 Ford Ranger

1 Answer

Diagrams


your oxygen sensor or sensors are located on your exhaust pipe just after your exhaust manifold

May 26, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
1992 Ford Ranger Logo

Related Topics:

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...