Question about 1999 GMC Jimmy

Open Question

99 gmc jimmy intake torque specs

Torque specs for intake m anifold

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

psds4
  • 293 Answers

SOURCE: 1998 GMC Jimmy Vortec V6 4.3L 4WD

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800bfc68
hope this helps

Posted on Oct 17, 2008

  • 2 Answers

SOURCE: remove airbag 99 gmc jimmy

I actually just took mine out today on a 1998 Gmc Jimmy. Its kind of simple now that ive done it. There are four ten millimeter bolts holding the passenger module in. you will need to drop your glovebox down so it is upside down to see these. It is easier if you take it right off. just take a shop light and look at the bottom of the module you will see two silver bolts (the only two ten mm down there) take them out. Then if you look up underneath you will see another up at the top left. To get this out you can hand wrench it or you can use a mini impact with an ajustable extension. to get the next the easiest way I found was to take off the trim aroung your speedometer get in the drivers seat and there is another ten millimeter nut on the top right (right by the vent holes) take that out then you are unbolted. Without going into tons of details when you start doing it you will quickly realsie how to do it it just takes some patience. Dont forget to pull the fuse before you do anything its a 15 amp fuse second row 3rd up in the panel inside the car. Hope this helps

Posted on Mar 04, 2009

  • 4 Answers

SOURCE: Bolt torque Specs

30 foot pounds

Posted on May 02, 2009

arauzvictor1
  • 466 Answers

SOURCE: need head bolt, intake manifold, and exhaust torque specs

Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Posted on Mar 06, 2010

  • 2926 Answers

SOURCE: head bolt torque specs on a 97 gmc jimmy 4.3

6c6b8b2.jpg
First, tighten the bolts to 25 ft. lbs. (34 Nm).
Next, tighten the bolts to 45 ft. lbs. (61 Nm).
Finally, tighten the bolts to 65 ft. lbs. (90 Nm).

Posted on Sep 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i find step by step directions to replace a intake manifold gasket in a 94 jimmy sl 4.5 litre? Aproxmitaly how long will it take aswell


Buy yourself a service manual from a auto parts store.They have torque specs and step by step instructions.

Dec 03, 2010 | 1994 GMC Jimmy

1 Answer

WHAT ARE THE TORQUE SPECS FOR A CRUSH SLEEVE ON A 2000 GMC JIMMY


There is no spec for that. the sleeve must be compressed until you have the correct pinion bearing preload. The pinion must take 3-5 inch pounds of torque to spin it.

May 12, 2010 | 2000 GMC Jimmy

1 Answer

I need the torque specs and torque sequence for my 1997 GMC Jimmy


if you donot have a shop manual go to library reference section and copy info from the professional motor manual under engine specs.

Apr 25, 2010 | 1997 GMC Jimmy

1 Answer

Im replacing my intake manifold gasket in my 2000 GMC Jimmy.. What else should I do while im in this far?? Or is that enough?


BE VERY CAREFUL WHEN CLEANING CATCH ALL DEBRIE IN A RAG THIS WOULD BE A GOOD TIME FOR TUNE UP IF NEEDED. MAKE SURE YOU CLEAN CLEAN CLEAN IF THIS HAS 4.3 BE CAREFUL ON INTAKE TORQUE. CHANGE COOLANT IF OVER 60,000 ON VEH. WITH MANUFACTURE SPEC. COOLANT.

Feb 11, 2010 | GMC Jimmy Cars & Trucks

1 Answer

What is the torque spec for the crank pulley bolt on a 95 gmc jimmy? never torqued down to specs, could that be the reason it falls off after a month or two of driving?


The torque is 70 lb. ft.

Before reinstalling the balancer check the key way for wear both on the balancer and the crankshaft. Also when reinstalling the balancer on the crankshaft it should be a press fit. A crankshaft balancer installer kit is needed to get the balancer bottomed out in other words.

Use some sealer on the key way to prevent an oil leak.

Nov 06, 2009 | 1995 GMC Jimmy

Not finding what you are looking for?
1999 GMC Jimmy Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...