Question about 2001 Saturn SL

Open Question

I cant find the torque specs for a saturn 2001 sl 1.9 l

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 327 Answers

SOURCE: Saturn Driver Seat

no it will not fit your vcar as its allignment is totally different from yours.

Posted on Dec 15, 2008

  • 186 Answers

SOURCE: solution for 1998 saturn sl

Hello DTC P0341 & P0133 very common saturn Codes.You need to check condition of Plugs & wires,If not New Replace All Plugs & Wires,also I would replace the #1#4 Coil for the P0341.For the P0133 Reaplce your front O2 sensor with an OEM sensor,not an aftermarket.

Posted on May 11, 2009

jeffbvegas1
  • 520 Answers

SOURCE: where is the coolant temperature sensor

These are located in the cylinder head in the back of the head...meaning 180 degrees from the belts and pulleys(front) or the side the transmission is on. Two sensors exist...the single wire sensor is for the dash gauge. Saturn pn# 21025106 is the one you need

Posted on Aug 12, 2009

matney68
  • 426 Answers

SOURCE: does my 2001 saturn sl 1.9l have a timing belt or chain?

It is a chain and its not the easiest but it could be worse.It is as follows:
1.9L SOHC Engine

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Right front wheel and splash shield
    NOTE: Place a 1 in. x 1 in. x 2 in. long block of wood between the torque strut and cradle to ease removal and installation of the torque engine mount.
    • 3 right side upper engine torque axis to front cover nuts and the 2 mount to midrail bracket nuts, allowing the powertrain to rest on the block of wood
    • Drive belt, tensioner and pulley
    • Power steering pump attaching bolts and set the pump to the side with the lines still attached
    • A/C compressor from the bracket and set aside with the lines attached
    • Camshaft cover
    • Using a strap wrench or a piece of wood wedged between the damper spoke and the lower side of the engine front cover, hold the damper and remove the bolt. With a suitable 3-jaw puller and the slots cast into the damper, pull the crankshaft damper/pulley assembly from the crankshaft.
    • Install the special oil seal replacement tool SA9104E, to be sure the front crankshaft timing sprocket is held firmly in place and prevent guide damage. Install with the flat side towards the crankshaft sprocket.
    • Remove or disconnect the following:
      • Front 4 oil pan bolts and cut the seal away from the front cover
      • Front cover bolts and carefully pry the cover away from the cylinder block at the pry location tabs, which are provided. Remove the cover from under the hood or through the wheel well
      • Front cover oil seal from the cover
      NOTE: During timing chain and sprocket removal, position the crankshaft 90 degrees past Top Dead Center (TDC), to be sure the pistons will not contact the valves upon assembly.
    • Carefully rotate the crankshaft clockwise so the timing mark on the crankshaft sprocket and keyway align with the main bearing cap split line (90 degrees past TDC).
    • Remove or disconnect the following:
      • Timing guides and tensioner
      • Camshaft sprocket bolt, using a 7⁄8 in. (21mm) wrench to hold the camshaft. Then, remove the timing chain and camshaft sprocket
      • Crankshaft sprocket
      To install:
    • Inspect the chain for wear and damage. Check the inside diameter of the chain, it should be no more than 16.77 in. (426mm). Inspect the chain guides for wear or cracks and the timing sprockets for teeth or key wear. Replace components as necessary.
    • Verify that the crankshaft keyway is positioned 90 degrees clockwise past TDC (keyway at 3 o'clock). The keyway should align with the split between the bearing cap and engine block.
    • Bring the camshaft up to No. 1 TDC by loosely installing the sprocket and rotating the sprocket until the timing pin can be inserted. The camshaft contains wrench flats to assist in turning the shaft. The dowel pin should be at 12 o'clock when the camshaft is at TDC.
    • Install the crankshaft sprocket, then rotate the crankshaft counterclockwise 90 degrees up to No. 1 TDC (keyway at 12 o'clock).
    • Position the chain under the crankshaft sprocket and over the camshaft sprocket. The timing chain should be positioned so that 1 silver link plate aligns with the reference mark on the camshaft sprocket and the other aligns with the downward tooth (at the 6 o'clock position) on the crankshaft sprocket. The letters FRT on the camshaft sprocket must face forward, away from the cylinder head and excess chain slack should be located on the tensioner side of the block.
    • Install or connect the following:
      • Timing pin to verify proper alignment of the camshaft and sprocket. Torque the sprocket bolt to 75 ft. lbs. (102 Nm).
      NOTE: Do not allow the camshaft retaining bolt to torque against the timing pin or cylinder head damage will result.
      • Timing chain guides with the words FRONT facing out. Install the fixed guide first and verify the chain is snug against the guide, then install the pivot guide. Torque the bolts to 19 ft. lbs. (26 Nm) and verify that the pivot guide moves freely
      • Retract the tensioner plunger and pin the ratchet lever using a 1⁄8 in. No. 31 drill bit inserted in the alignment hole at the bottom front of the component
      • Tensioner. Torque the bolts to 14 ft. lbs. (19 Nm), then remove the drill bit
    • Make one final check to verify all components are properly timed, then remove all timing pins.
    • Install or connect the following:
      • Seat a new front cover oil seal using the installation tool with a press
      • If the engine front cover casting or assembly is replaced, the 3 torque axis mount studs should also be replaced. Torque the new studs to 19 ft. lbs. (25 Nm).
1.9L (DOHC) Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. drain the engine oil.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Right front wheel and splash shield
    NOTE: Place a 1 x 1 x 2 in. (25 x 25 x 51mm) block of wood between the torque strut and cradle to ease removal and installation of the torque engine mount.
    • 3 right side upper engine torque axis to front cover nuts and the 2 mount to midrail bracket nuts, allowing the powertrain to rest on the block of wood
    • Drive belt, tensioner and pulley
    • Power steering pump attaching bolts and set the pump to the side with the lines still attached
    • A/C compressor from the bracket and set it to the side with the lines attached
    • Camshaft cover
  4. Using a strap wrench or a piece of wood wedged between the damper spoke and the lower side of the engine front cover, hold the damper and remove the bolt. With a suitable 3-jaw puller and the slots cast into the damper, pull the crankshaft damper/pulley assembly from the crankshaft.
  5. Install the special oil seal replacement tool SA9104E or equivalent, to be sure the front crankshaft timing sprocket is held firmly in place and prevent guide damage. Install with the flat side towards the crankshaft sprocket.
  6. Remove or disconnect the following:
    • Front 4 oil pan bolts and cut the seal away from the front cover
    • Front cover bolts and carefully pry the cover away from the cylinder block at the pry location tabs, which are provided. Remove the cover from under the hood or through the wheel well
    • Front cover oil seal from the cover
    NOTE: During timing chain and sprocket removal, position the crankshaft 90 degrees past top Dead Center (TDC), to be sure the pistons will not contact the valves upon assembly.
  7. Carefully rotate the crankshaft clockwise so the timing mark on the crankshaft sprocket and keyway align with the main bearing cap split line (90 degrees past TDC).
    • Timing guides and tensioner
    • Camshaft sprocket bolt, using a 7⁄8 in. (21mm) wrench to hold the camshaft. Then, remove the timing chain and camshaft sprocket
    • Crankshaft sprocket

Posted on Nov 30, 2009

muntejaya
  • 10421 Answers

SOURCE: why will my 2001 Saturn SL 1 heat up

The are many things that can make your car heat up such as : - water pump problem - Cooling fan problem - Radiator problem - Cooling media problem. - Your driving style You need to trace which problems are persist and have them fixed.

Posted on Nov 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for 2003 saturn veu 3.0


2003 Vue Torque Specs? - SaturnFans.com Forums

www.saturnfans.com > ... > Models > Saturn Vue > Vue Tech

Feb 4, 2009 - 6 posts - ‎5 authors
Does anyone have/know where I can get the torque specs for a Saturn Vue? ... See attached for 2003 2.2 and 3.0 engine torque and front ... need vue torque specs
9 posts
Oct 13, 2010
Filter cap and drain plug torque spec
14 posts
Feb 19, 2009
Lug Nut Torque?
5 posts
Oct 6, 2008
S-Series Torque Specifications
15 posts
Nov 13, 2004
More results from www.saturnfans.com

Nov 26, 2015 | Saturn Cars & Trucks

1 Answer

Pressure plate torque spec


Can't imagine that is anywhere near enough unless it's an 1/8 inch bolt!! If it's 3/8 or so I would think 35 with locktite.

Apr 07, 2014 | Saturn Vue Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

1996 Saturn SL 1. Does the crankshaft pulley bolt requeire sealer?


According to a book, I don't know, but my rule of thumb is to put red loctite (Loctite 277) on all bolts for flywheel or anything ataching to the crank that I don't want comming off. Then again I work on diesel applications so my rule of thumb for auto could be off base. One thing though, when using loctite you take the dry torque spec of the bolt and multiply by 75% or 0.75 and that is your new torque spec. also anything touching a crankshaft or camshaft i would sugest using new bolt and or nuts.

Jul 24, 2011 | 1996 Saturn SW

1 Answer

Looking for head bolt torque for 95 SOC saturn. im having valve guides replaced


The torque spec are as follows, step one is 22 ftlbs then step 2 is 33ftlbs and the third step is to tighten bolts 90degrees more also the bolt tightening sequence is here, this is a diagram of the bolts good luck and i hope this helps.johnjohn2_60.gif

Jan 10, 2011 | 1995 Saturn Sl

1 Answer

2001 vw 1.8 litre gas awv engine spec I am rebuilding my 2001 new beetle engine after the head cracked and I need the engine torque specs. Thanks


Bore × stroke 81.00 mm × 86.40 mm 3.19 in × 3.4 in Cylinders s-4 SOHC Single overhead camshaft DOHC Double overhead camshaft OHV Overhead valves TS Two stroke SV Side valves
  • Sl
  • Sleeve valves
  • oise
  • Overhead inlet side exhaust
  • 5 valves per cylinder
    20 valves in total
    compression ratio
    9.30:1 fuel system
    MPFi Maximum power 150.1 PS (148.0 bhp) (110.4 kW)
    @ 5700 rpm Specific output 83.1 bhp/litre
    1.36 bhp/cu in Maximum torque 210.0 Nm (155 ft·lb) (21.4 kgm)
    @ 1750 rpm bmep 1481.7 kPa (214.9 psi) Specific torque 117.91 Nm/litre

    May 01, 2010 | 2001 Volkswagen Beetle

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    140 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Saturn Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7772 Answers

    Are you a Saturn Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...