Question about Cars & Trucks

Open Question

How to remove outer cv joint 1998 600 grizzly

Everthing is apart except the shaft is still in the machine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Nitrotrike
  • 589 Answers

SOURCE: CV joint replacement

Generally no tool is required. If you use a "pickle fork" you will risk damaging the dust boot.

Have you tried whacking the spindle right near where the ball joint stud comes through? This will take a few good shots to break it loose.

Be careful not to hit the threads!

Posted on Jun 25, 2008

Ad
  • 83 Answers

SOURCE: 97 toyota celica outer cv boot replacement passenger side

have you undone the main hub bolt, if yes, there could be two different items holding the cv joint on, one is a small circlip in the joint end, or the other is just like an expanding metal ring again only small. what i had to do to change my one was take the driveshaft out (easier to see whats there) then gently (rubber hammer) hit the CV joint it should then fall off to allow you to change the CV joint. I spent over an hour trying to get the metal ring off, then after taking driveshaft off it was changed and back on in ten mins. Or you can go to a motor factors or similar and get a boot puller, my opinion hammer works better lol

Posted on Jan 25, 2009

  • 6982 Answers

SOURCE: 1998 grand cherakee driver side cv joint removal

You can find instructions for doing this in any half decent manual. One thing they usually don't tell you is when removing the large axle nut on the end, it helps to put a spare tire on with no center cap and with the vehicle on the ground, break that nut free before starting the job. without air tools, it's next to impossible to remove it when jacked up.

Posted on Mar 10, 2009

cadman000
  • 607 Answers

SOURCE: cv boot clamp came off somehow from the outer hub assembly

athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Posted on Apr 04, 2009

  • 1986 Answers

SOURCE: CV JOINTS?

The CV joints are needed to transfer the torque at a constant speed to steered wheels as well as to accommodate up and down motions of the suspension.
You will find CV joints in all front-wheel drive cars. Many rear- and four-wheel drive cars and trucks have CV joints as well. The CV joint is packed with grease and protected by the rubber or plastic boot.
It does not require any maintenance and supposed to last very long provided that protective boot will not get damaged.

Posted on Aug 24, 2009

Testimonial: "NOW I UNDERSTAND"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

.I have removed the end of drive shaft out of the hub[rhs] ,other end of shaft is still attached.will the cv joint come off the end of the shaft so i can fit the new boot?


Which vehicle are you working on?

Some of these CV-joints are designed with an outside circlip. An example of such a setup would be on an Opel/Vauxhall. On cars like these with an outside circlip it is possible, after cleaning the grease to actually see the circlip and with a good quality circlip pliers, it is possible to expand the circlip sufficiently to remove the outer CV- joint with a sharp tap while keeping circlip expanded all whilst the CV- joint is still attached to the vehicle on the inner side.

On other designed CV- joints the circlip sits on the inside of the CV joint. In other words you cannot see the circlip at all. If it is such a design then the compete CV- joint unfortunately has to be removed.

Why it has to be removed if it an inside designed circlip?

Well in most cases it requires a rather sharp tap of a rubberized hammer on the outer CV to remove it from the drive shaft. This is not possible whilst the CV-joint is attached as damage to inner CV flange is very likely.

Apr 22, 2015 | Cars & Trucks

1 Answer

How do I remove the cv axle in a ford telstar 1993 - both sides


Line the outer up in the right place and enter it until the circlip is against the splines . Use a large heavy hammer and rap the end of the shaft hard and the circlip will pop in the groove and allow the shaft to go home.. Removal from the shaft is much the same as it has a circlip inside the transmission. So remove the shaft from the wheel. Use a hammer to hit the cv joint so that it jumps the shaft out of the transmission .

Mar 20, 2014 | 1999 Isuzu Rodeo

3 Answers

The rod that goes into the trasnmission (cvc joint) how do i remove it so i can pull the trasmission?


you're talking about the axle, pry bar it off, its held by little snap rings around the shaft, it basically just pulls out, sometimes can be difficult

Oct 23, 2010 | 1996 Volkswagen Jetta

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

I've got a 1999 2500 Chevy Silverado , that I need to change a cv boot on , can u assist me.?


CV-Joints
Overhaul
These vehicles use several different types of joints. Engine size, transaxle
type, whether the joint is an inboard or outboard joint, even which side of the
vehicle is being serviced could make a difference in joint type. Be sure to
properly identify the joint before attempting joint or boot replacement. Look
for identification numbers at the large end of the boots and/or on the end of
the metal retainer bands.

The 3 types of joints used are the Birfield Joint, (B.J.), the Tripod Joint
(T.J.) and the Double Offset Joint (D.O.J.).

NOTE: Do not disassemble a Birfield joint. Service with a new joint or
clean and repack using a new boot kit.

The distance between the large and small boot bands is important and should
be checked prior to and after boot service. This is so the boot will not be
installed either too loose or too tight, which could cause early wear and
cracking, allowing the grease to get out and water and dirt in, leading to early
joint failure.

NOTE: The driveshaft joints use special grease; do not add any grease
other than that supplied with the kit.

Double Offset Joint
To Remove:

NOTE: The Double Offset Joint (D.O.J.) is bigger than other joints
and, in these applications, is normally used as an inboard joint.


  1. Remove the halfshaft from the vehicle.
  2. Side cutter pliers can be used to cut the metal retaining bands. Remove the
    boot from the joint outer race.
  3. Locate and remove the large circlip at the base of the joint. Remove the
    outer race (the body of the joint).
  4. Remove the small snap ring and take off the inner race, cage and balls as an
    assembly. Clean the inner race, cage and balls without disassembling.
  5. If the boot is to be reused, wipe the grease from the splines and wrap the
    splines in vinyl tape before sliding the boot from the shaft.
  6. Remove the inner (D.O.J.) boot from the shaft. If the outer (B.J.) boot is
    to be replaced, remove the boot retainer rings and slide the boot down and off
    of the shaft at this time.

To Install:

NOTE: Be sure to tape the shaft splines before installing the boots.
Fill the inside of the boot with the specified grease. Often the grease supplied
in the replacement parts kit is meant to be divided in half, with half being
used to lubricate the joint and half being used inside the boot.


  1. Install the cage onto the halfshaft so the small diameter side of the cage
    is installed first. With a brass drift pin, tap lightly and evenly around the
    inner race to install the race until it comes into contact with the rib of the
    shaft. Apply the specified grease to the inner race and cage and fit them
    together. Insert the balls into the cage.
  2. Install the outer race (the body of the joint) after filling with the
    specified grease. The outer race should be filled with this grease.
  3. Tighten the boot bands securely. Make sure the distance between the boot
    bands is correct.
  4. Install the halfshaft to the vehicle.

Except Double Offset Joint
To Remove:


  1. Disconnect the negative battery cable. Remove the halfshaft.
  2. Use side cutter pliers to remove the metal retaining bands from the boot(s)
    that will be removed. Slide the boot from the T.J. case.
  3. Remove the snap ring and the tripod joint spider assembly from the
    halfshaft. Do not disassemble the spider and use care in handling.
  4. If the boot is be reused, wrap vinyl tape around the spline part of the
    shaft so the boot(s) will not be damaged when removed. Remove the dynamic
    damper, if used, and the boots from the shaft.

To Install:


  1. Double check that the correct replacement parts are being installed. Wrap
    vinyl tape around the splines to protect the boot and install the boots and
    damper, if used, in the correct order.
  2. Install the joint spider assembly to the shaft and install the snap ring.
  3. Fill the inside of the boot with the specified grease. Often the grease
    supplied in the replacement parts kit is meant to be divided in half, with half
    being used to lubricate the joint and half being used inside the boot. Keep
    grease off the rubber part of the dynamic damper (if used).
  4. Secure the boot bands with the halfshaft in a horizontal position. Make sure
    distance between boot bands is correct.
  5. Install the halfshaft to the vehicle and reconnect the negative battery
    cable.






Check the CV-boot for wear
tccs7030.jpg








Removing the outer band from the CV-boot
tccs7031.jpg








Removing the inner band from the CV-boot
tccs7032.jpg








Removing the CV-boot from the joint housing
tccs7033.jpg








Clean the CV-joint housing prior to removing boot
tccs7034.jpg








Removing the CV-joint housing assembly
tccs7035.jpg








Removing the CV-joint
tccs7036.jpg








Inspecting the CV-joint housing
tccs7037.jpg








Removing the CV-joint outer snap ring
tccs7038.jpg








Checking the CV-joint snap ring for wear
tccs7039.jpg








CV-joint snap ring (typical)
tccs7040.jpg








Removing the CV-joint assembly
tccs7041.jpg








Removing the CV-joint inner snap ring
tccs7042.jpg








Installing the CV-joint assembly (typical)
tccs7043.jpg




prev.gif next.gif

Oct 07, 2010 | 2002 Chevrolet Silverado 2500HD

1 Answer

How do I get the cv joint seperated from the shaft of the axel because i need to do that to place a new cv boot on?


To replace the outer boot on this shaft you have to first remove the inner joint from the shaft, then remove the outer joint boot from the shaft and joint by sliding it back down the shaft. Do not remove the outer CV joint from the shaft. I believe you have to replace the entire axle shaft if it is removed as it's not made to be removed and reinstalled. I would actually suggest replacement of the entire shaft instead of just the boot anyway unless you were lucky enough to catch a leaking boot as soon as the boot went bad as it takes such a very small amount of road grit to start the damage that will eventuall wear out the joint and then you have to take the axle out again. [just my opinion as over the years I've seen dozens of bad boots cause joints to fail a short time later] Hope this helps out a bit and good luck!

Jun 25, 2010 | 2005 Chevrolet Colorado

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

1 Answer

Inner cv joint disassembly


If you are changing the CV joint with shaft, after getting the outer end of the shaft out of the hub, Take a small pry-bar and pry the shaft out of the tranny.

Mar 14, 2009 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...