Question about 1996 Lincoln Town Car

1 Answer

I used the last of my money to buy the part now I cant fix my car

I cant find the ignition control module

Posted by on

  • Anonymous Nov 29, 2008

    where is the ignition module located?

  • Anonymous Mar 10, 2009

    cant find ignition module

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Lincoln Master
  • 1,779 Answers

It's located under the hood, on the upper fire wall, driver side, near master brake cylinder

Posted on Oct 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fix a problem with not starting when car is hot i still turns over


not starting when hot indicates an electrical problem that comes from a component breaking down when hot.
Items that fall into this category are coils,coil packs, injector controls,injectors, ignition modules and fuel vaporization ( low fuel pressure from failing fuel pump/relay
I would leave the pump as an absolute last but would be looking at coil or ignition module. have you run the fault codes to check for other sensor problems such as cam/crank position sensors or immobiliser problems. All subject to heat affected problems.

Feb 07, 2015 | Cars & Trucks

2 Answers

Code 65535 what does that mean


How do i remove t-mobile content lock with out credit card or by going to t-mobile shop.

Apr 05, 2013 | Cars & Trucks

1 Answer

My van has no spark to the distrutor cap


CHECK THE FUSE TO IGNITION SYTEM THAT CONTROL COIL AND IGNITION MODULE.IF FUSE GOOD.SCAN VECHICLE FOR FAULTY IGNITION MODULE FAULTY CRANKSHAFT SENSOR AND PCM.HAVE VECHICLE CODE SCAN WITH A SCANNER THAT WILL SAVE YOU MONEY AND TIME.

Jan 12, 2011 | 1994 Chevrolet Astro

1 Answer

My pontiac sunfire just turn off when i was driving .I cant trun it back on...


WELL COULD BE FUEL PUMP. STOPPED UP FUEL FILTER,WATER IN THE FUEL.FAULTY IGNITION MODULE.FAULTY CAMSHAFT SENSOR,FAULTY CRANKSHAFT SENSOR.FAULTY IDLE SPEED CONTROL. MANY THINGS CAN CAUSE VECHICLE TO SHUT DOWN. BEST TO HAVE VECHICLE SCANNED WITH CODE SCANNER.THAT WAY IT WILL HELP PIN POINT PROBLEM QUICKER SO YOU WONT SPEND LOTS OF MONEY BUYING TOO MANY NEW PARTS.

Dec 27, 2010 | 1998 Pontiac Sunfire

1 Answer

1996 FORD EXPLORER , MISS FIRE ON CYL # 2, 1ST REPLACED PLUGS AND WIRES, THEN THE COIL PACK AND LAST THE FUEL INJECTOR BUT PROBLEM STILL THERE, ANY HELP WOULD BE GREAT


OK,
Have you tried the following:


Ignition Control Module (ICM) REMOVAL & INSTALLATION NOTE: Only the EEC-IV ignition systems use an external ICM. EEC-V systems have incorperated the ICM into the Power Control Module (PCM).
  1. Disconnect the negative battery cable.
  2. Detach the wiring harness connector(s) from the ICM.
  3. Remove the mounting bolts, then remove the ICM. To install:
  4. Position the ICM onto the inner fender apron and install the mounting bolts. Tighten the bolts to 22–31 inch lbs (2.5–3.5 Nm).
  5. Attach the wiring harness connector(s) to the ICM.
  6. Connect the negative battery cable. Fig. 1: Ignition control module and mounting location on the 2.3L, 2.5L engine 89682g32.gif
    Fig. 2: Ignition control module used on all EEC-IV systems except the 2.3L engine 89682g33.gif
    Fig. 3: Ignition control module mounting on all EEC-IV systems except the 2.3L engine 89682g34.gif
prev.gif next.gif

Jul 11, 2010 | 1996 Ford Explorer

4 Answers

Car turns over will not start no spark at the spark plugs


CHECK IGNITION MODULE FUSE.AND CHECK FOR POWER GOING TO MODULE AND COILS.IF NO POWER PROBLEM IN IGNITION MODULE FUSE OR LOOSE BROKEN WIRE.IF POWER GOING TO IGNITION MODULE.THE IGNITION MODULE FAULTY.TO SAVE MONEY AND TIME.HAVE CAR SCANNED TO MAKE SURE YOU DONT HAVE ECM OR PCM PROBLEMS.YOU DONT WANT TO BUY A IGNITION MODULE IF YOU DONT NEED IT BECAUSE THEY COST FROM $100.00 TO $200.00.THATS WHY SCAN IT FIRST.

Apr 04, 2010 | 1991 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1996 Lincoln Town Car Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...