Question about 1996 Nissan Maxima

Open Question

Location of crankshaft position sensor on 1996 nissan maxima

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 383 Answers

SOURCE: CANNOT FIND THE CRANKSHAFT POSITION SENSOR

cerebral_eni: The crank position sensor is located at the back of the engine block just below the cylinder head. It actually projects into the bell housing and reads the teeth on the flywheel where it references TDC for #1 cyl and RPM's of the crank. It's a "Hall effects generator". Unless you are into electronics and have a lab scope to look for a square wave pattern, I will continue with my other input.
Nissan has a recall campaign on the crank angle sensors.
The campaign # is 07V527000:ECM update for stalling;
NHTSA07V527000 NOV 07,
The symptom was brief malfunction of sensor causing the engine to quit running which could potentially put the vehicle at risk for a collision. The sensors would ultimately fail. There was also a voluntary recall on the reprogramming of the ECM's due to stalling problems. TSB# NTB07-081, Campaign ID#R0712
I hope this information is of some assistance to you. You may be able you get your car repaired under warranty! Good Luck!

Posted on Apr 08, 2009

johnny5846
  • 379 Answers

SOURCE: location of a o2 sensor 2001 nissan maxima

bank 1 refers to the side of the engine that #1 cylinder is on , and sensor 2 refers to downstream , after the catalytic converter. , this link shows bank 1 on a 2001 nissan maxima V6 being on the firewall side . if you had a 4 cylinder it would be downstream after the catalytic converter .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm



Posted on Jan 04, 2009

  • 1 Answer

SOURCE: 2004 Nissan altima 2.5 liter Crankshaft Position Sensor

Yes, the sensor can be replaced in your garage (if you have some decent auto repair experience).
This is not an easy job due to the location of the crank sensor.

Below are the steps I used to replace the crankshaft position sensor.
The steps are for a 2004 Nissan Altima with a 2.5 liter engine.

Nissan has a crank and cam sensor kit. I would not buy any aftermarket sensors because of the effort required to replace the sensors. (I do not work for Nissan). The information below is compiled of tips I found on the internet and my own experience. Even though these procedures may appear lengthy, it took me much longer to figure out the correct steps involved for this task.
Even though I have included all of the steps (and hints) I used… THIS IS NOT AN EASY JOB FOR THE “DO IT YOURSELFER”

CRANK SENSOR IS LOCATED AT FIRE WALL SIDE OF BLOCK BETWEEN MOTOR MOUNT AND FLYWHEEL. YOU GET TO IT FROM TOP.
Remove the (4) allen head bolts that hold the plastic engine cover. Remove the air tube that connects the throttle chamber to air filter box. Pull off the valve cover breather hose with the air tube. Now place a drop light under the two rubber heater hoses (at the firewall on the drivers hand side), shining the light forward towards the back side of the block (below the intake runners). To see the crankshaft sensor and connector, look between the valve cover and the throttle chambers (intake runners) on the drivers side, look straight down toward the ground… look for the sensor with a black wire connector with a green tab on the side, held to the engine block with a gold colored 10mm hex headed bolt. You will need to view the sensor from this position as you are following the steps below to remove and install the crank sensor. There is a large wiring harness bracket attached to the transmission bell housing that was temporarily unbolted to aid with the removal and installation of the crank sensor.

What turned out to be the biggest problem was the connector securing the wiring harness to the sensor. Unlike the camshaft position sensor connector that is removed by squeezing in on a tab located at the top of the connector, the crank position sensor was secured to the harness via some green colored push button assembly. To remove the crank sensor connector, the green tab must depressed ALL THE WAY DOWN (towards the block) UNTIL THE GREEN TAB LOCKS INTO PLACE - REMAINING IN A “PUSHED IN” POSITION (You should hear a “click”). I was able to accomplish this by viewing the connector as described above and at the same time, reach around the back side of the engine using a 6” – 8” flat blade screw driver (with a large head) and push the green tab in towards the block until it locked into place. After the green tab was depressed and locked, (still viewing from above) I repositioned my hand holding a smaller flat blade screw driver to gently pry the connector off the sensor inserting the blade of the screw driver between the bottom of the connector and the crank sensor (a slight twist should do it). I do not recommend pulling on the connector wires or trying to pull the connector off with pliers as damage may result - because in my world of auto repair, if there is a chance that something will break because I am not careful… IT WILL BREAK! After you have removed the connector and while viewing from above, use a ¼” drive ratchet with a 6” extension and a 10mm socket to loosen the gold bolt holding the crank sensor in place. I recommend that you loosen the bolt with the socket, then reach your hand around to the connector and remove the bolt by hand. After the bolt is removed, use an 8” slip jaw pliers - set at its widest opening setting – to grab the sensor. First twist then pull out the sensor.

Be sure to clean the inside of the sensor’s wiring connector with break cleaner spray and blow out with compressed air to get rid of any oil that may have leaked into the connector from the defective crank sensor… this is what probably caused the trouble code in the first place.

You are now ready to install the new crank sensor. If you purchased the crank and cam sensor kit from Nissan, make sure that sensor with white dot at bolt whole goes to the crank. Be sure to oil the rubber “O” ring. I was not able to get the green tab on the connector to snap back into place while the new sensor was installed in the block. I installed the connector to the sensor while it was out of the block – the green tab still did not pop back into its original position on its own – so…while the connector was installed as far down as I could push it, it used a small flat blade screw driver to push on the bottom of the green tab towards the top. That did the trick. While viewing from above, I placed the crank sensor back into the block. I was not able to get the rubber “O” ring to seat within the block by hand. I used the gold bolt to draw the sensor in while slowly tightening. HINT: I taped the outside of the washer of the crank sensor bolt to the 10mm socket to hold the bolt on place while I inserted the bolt into the block… you can do this by hand, but I didn’t want to drop the bolt . I also taped the socket to the ratchet extension so the socket would not get stuck on the bolt (it’s a snug fit down there).
If you were able to accomplish the above procedures, the cam sensor is a snap to remove in install. It is located in the driver’s side portion of the head facing the wheel.
Remember to reinstall all brackets and items that were removed.
Good luck!

Posted on Feb 17, 2009

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

  • 1 Answer

SOURCE: Speed sensor location on a Nissan Maxima 2000 GXE...

There are two speed sensors one is called a revolution sensor that is located on the case of the transmission. You can take the driver side wheel off and see the sensor on the top of the case of the transmission. A 10mm bolt is holding it in. Easy fix

Posted on Jun 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Nissan Maxima is showing code P1335 Manufacturer Controlled Ignition System Or Misfire. Where is this and how do I fix it?


DTC P1335 is not a ignition code. It is for the crankshaft position sensor. You will most likely have to replace that. symptoms sound like the crankshaft position sensor.

Oct 09, 2014 | 1996 Nissan Maxima

1 Answer

2000 NISSAN MAXIMA SE CRANKS BUT WON'T START


Gets scanner check for any codes. Sounds like crankshaft position sensor or camshaft position sensor. Check for codes

Nov 21, 2013 | 2000 Nissan Maxima

1 Answer

P1335 code


that code would be your crankshaft position sensor or the wire attached to it,is going bad.also a very slim chance that a dead or weak battery could cause this code too.The crankshaft position sensor is located on the oil pan (upper) facing the crankshaft pulley.

Jun 02, 2012 | 1995 Nissan Maxima

2 Answers

Where is the crankshaft position sensor on a 1996 nissan maxima/photo view


When you looked in the Engine Control Crankshaft position sensor located on the left side of the engine with easy reach and view

Nov 04, 2011 | 1996 Nissan Maxima

2 Answers

Where is the crankshaft sensor located ?


The crankshaft position sensor (POS) is located on the oil pan facing the gear teeth (cogs) of the signal plate. It detects the fluctuation of the engine revolution.
After replacement, ECM reprogramming is required.
This vehicle may be subject to voluntary recall, CAMPAIGN I.D. # R0606, that involves the crankshaft position sensor:

Quote: Nissan has determined that on some 2003 - 2004 Altima and Sentra vehicles with the 2.5 liter engine the operation of the crank angle sensor is significantly affected by variations in temperature that occur due to the unique location of the sensor in the engine. Under certain driving conditions, these variations in temperature can be large enough to cause a brief interruption in the signal output from the sensor. If the interruption in the signal from the sensor is so brief that the Electronic Control Module (ECM) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at low speed.

Jun 29, 2010 | 2004 Nissan Sentra

3 Answers

Knock sensor 1996 v6 3.3 nissan pathfinder


The Crankshaft Position Sensor is located: Under hood, driver side, front engine area, mounted rear of crankshaft pulley
The Knock Sensor is located: Under hood, center, front engine area, below intake manifold, mounted on block

Jun 14, 2009 | 1996 Nissan Maxima

1 Answer

Had fire and need to know where to fine crankshef positioning sensor plug on wiring harness on 96 ram 1500 v6 3.9


The crankshaft positioning sensor should located around the crank pulley. The plug in should just be a few inches away from the sensor itself.

Mar 24, 2009 | 1996 Nissan Maxima

3 Answers

Crankshaft poistion sensor location for 2005 nissan altima


Its right next to the passenger side drive shaft, where it goes into the transmission. Right above the drive shaft. It s black with green slider inside of the connector and it has 3 wires coming out of it.

Jul 23, 2008 | 2005 Nissan Altima

Not finding what you are looking for?
1996 Nissan Maxima Logo

Related Topics:

1,122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...