Question about Ford Cars & Trucks

Open Question

Replacement of oil pan on 1997 f250hd with 5.8 351 windsor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

leetamara
  • 702 Answers

SOURCE: 78 Ford Thunderbird w/ 351 Windsor motor

You'll need to raise the engine to replace the oil pan. Take the trans./converter loose, remove the engine mounts, wiring, fuel line, and anything else that could be a problem with raising the engine. You can use 2 6 x 6's and place under the engine mounts and rest the engine on these. This should provide you with room to drop the pan.

Posted on Jun 25, 2008

ah1f39
  • 34 Answers

SOURCE: Crankcase Capacity

If it is a factory car pan 5qts,
Drain pan, add 5qts, run 5min check oil.


http://www.sansaworldmp3.com/
http://www.sansaworld.com/

Posted on Apr 18, 2009

  • 1071 Answers

SOURCE: 1997 f250-5.8 - 351 windsor. runs fine when

i would check the fuel pressure it sounds like the pump is bad

Posted on Aug 06, 2009

  • 164 Answers

SOURCE: need info to rebuild 351 windsor motor 1998

port polish only on heads, they crack plus valve job. on the block and cam, that motors all torque so go with low end output, fat cam, 30 over max on bore-they crack. safest way for big power is a stroke kit. call edelbrock tell them you wishes and what you have now, main thing is how much your gonna have to bore to clean up walls, and they give you some good options. unless you have alota money and dont require this motor to be dependable dont expect more than 320hp and 350 ft of torque. 302 will take you farther cheaper and lighter for your money. if your talking for a car and not a truck- go 302 and dont look back

Posted on Aug 26, 2009

Testimonial: "thanks for your help good information"

  • 1757 Answers

SOURCE: i need a firing order diagram for 1997 f250 351

For the 1997 Ford F250 5.8L = 351:

Firing Order:
1-5-4-2-6-3-7-8

Cylinders:
...(back)
4...........8
3...........7
2...........6
1...........5
...(front)

Distributor:
....(back)
(+).5....1
4.............8
2.............7
....6....3..(+)-screw
....(front)

Let me know if helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It has a 351 Windsor motor in it. I has a terrible knocking sound. We replaced the main bearing and timing chain. What could it be?


How were the rod bearings? I always check them whenever replacing the main bearings. Why did you only say "main bearing"? There are always more than one.

could also be part of the fuel pump dropping do into the oil pan is now hitting the crank, but you checked the oil pan for "bits and pieces" when you took it off to change the main bearing - right?

Mar 31, 2015 | 1970 Ford Mustang

1 Answer

HOW DO I CHANGE OIL PAN GASKET IN A 1997 ACURA TL


Drain the oil, Remove the bolts/screws holding the pan onto the bottom of the engine. Remove all traces of old gasket. Clean the mating surfaces. Use bearing grease to stick the gasket onto the engine. Replace the pan and all bolts.

Nov 14, 2014 | Cars & Trucks

1 Answer

Oil pump ,,,where is the oil pump located on a 1997 dodge caravan


Hello
Welcome!
Oil pump is located on the oil pan.
Parts needed,,,oil,,,, oil filter,,,, oil pan gasket,,, oil pump,,,, oil pump pickup tube..
time to do this,, about 3 hours
Instructions,
Raise van place on 2 jack stands
drain oil remove oil filter fill new filter install.
remove bolts from oil pan,
remove oil pan..
remove 2 bolts that hold oil pump and tube.

install new pump and tube tork bolts to 45 fp
replace oil pan gasket and install oil pan
tork pan bolts to 35" pounds
install drain plug
fill with oil
start and check for leaks

let me know if i can help more

Jul 17, 2010 | 1997 Dodge Caravan

1 Answer

How to replace my oilpan on my 94 ford bronco, 351 windsor engine


you will have to raise the engine so you can get the oil pan off

Apr 15, 2010 | 1996 Ford Bronco

1 Answer

I need to replace the oil pan gasket on my 1997 Lincoln Continental, can this be done without removing the catylitic converter?


According the manual...no. Here is a cut and paste from it....

Oil Pan REMOVAL & INSTALLATION 3.8L Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Drain the oil pan, then remove the oil filter. Position the drain pan out of the way.
  4. Remove the dual converter Y-pipe assembly.
  5. Remove the starter motor. For details, please refer to the procedure located earlier in this section.
  6. Remove the engine rear plate/converter housing cover.
  7. Remove the retaining bolts and remove the oil pan.

Apr 03, 2009 | 1997 Lincoln Continental

1 Answer

REPLACING OIL PAN


hi no you dont have to remove the oil engine frim the car.just jack the car up and suport it.

Feb 02, 2009 | 1997 Cadillac DeVille

1 Answer

Crankcase Capacity


If it is a factory car pan 5qts,
Drain pan, add 5qts, run 5min check oil.


http://www.sansaworldmp3.com/
http://www.sansaworld.com/

Aug 16, 2008 | 1984 Ford Mustang

1 Answer

78 Ford Thunderbird w/ 351 Windsor motor


You'll need to raise the engine to replace the oil pan. Take the trans./converter loose, remove the engine mounts, wiring, fuel line, and anything else that could be a problem with raising the engine. You can use 2 6 x 6's and place under the engine mounts and rest the engine on these. This should provide you with room to drop the pan.

Jun 24, 2008 | Ford Thunderbird Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...