Question about Honda CRV

Open Question

Honda crv purge control solenoid valve closed struck

Location and how to replace it

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 77 Answers

SOURCE: where is the purge valve located on a 2004 honda LX?

It is with a 2 wire Black connect located next to the throttle body. Locate the green cap on the evap hose and follow it to the throttle body and that is the purge valve.

Posted on May 17, 2009

Ad
ghost4548
  • 776 Answers

SOURCE: Location of the Purge Control Valve for 2003 Hyundai Tiburon

There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Posted on Jun 06, 2009

  • 88 Answers

SOURCE: Location of Honda Accord Canister purge solenoid

on canister close to gas tank

Posted on Sep 16, 2009

  • 449 Answers

SOURCE: location of Idle control valve on 04 CRV

It's not a easy job but I'm pretty sure you had one of those problems where the idle surges if this is the case take out the air intake tube that leads to the throttle body, get a can of carburetor fluid and spray around the throttle body. You will need someone to start the car and hold the gas peddle to 2500 rpm while you do this the car will shut of when you do this, restart the car and repeat the process until half of the can is used up. Now check your antifreeze level fill if needed and reset you check engine light. Now you can take the idle air back and get your money.

Posted on Nov 17, 2009

johnjohn2
  • 5763 Answers

SOURCE: replacing cruise control bulb on honda crv 2006

JUST POP SWITCH OUT AND BULB GOES INTO SWITCH USE SMALL SCREW DRIVER TO REMOVE YOU WILL HAVE TO TWIST IT COUNTERCLOCKWISE TO REMOVE, TWIST CLOCKWISE TO INSTALL.

Posted on Apr 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is purge valve located?


How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...


Dec 18, 2015 | Cars & Trucks

1 Answer

What does code p1447 mean ...???


The code says "evap purge flow monitor fault"
Possible causes include ...
- EVAP canister purge volume control solenoid valve stuck closed.
- EVAP control system pressure sensor and its circuit.
- Loose, disconnected, or improper connection of rubber tube.
- Blocked rubber tube.
- Blocked or bent rubber tube to MAP/BARO switch solenoid valve.
- Cracked EVAP canister.
- EVAP canister purge volume control solenoid valve.
- Closed Throttle Position Switch.
- Improper connection of one-way valve.
- Blocked purge port.
- EVAP canister vent control valve.


This is a "jackpot" code. It points to so many possible causes as to be almost useless.

Feb 15, 2013 | 1996 Nissan Maxima

1 Answer

How do you replace the evap. purge valve solenoid on 2005 kia sportage


The canister purge valve is a computer controlled solenoid valve that allows any stored fuel vapors in the charcoal canister to be recycled back into the engine combustion process. The valve is typically located on or near the throttle body. The canister purge valve is controlled by the power train control module (PCM). The canister purge valve is closed each time the power train computer runs the OBD-II (Onboard Diagnostic Generation II) EVAP monitoring self-test.--------------------------------------------------------------------------------
renault can clip

Jan 05, 2013 | Cars & Trucks

1 Answer

How do I resolve diagnostic code P0455 on my 2005 Chevrolet Tahoe?


Here is the definition and possible causes.

Possible causes - Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking
P0455 CHEVROLET Description This diagnosis detects leaks in the Evaporative Emission System (EVAP) purge line using engine intake manifold vacuum. If pressure does not increase, the Engine Control Module (ECM) will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition.


The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.
Read more: http://engine-codes.com/p0455_chevrolet.html#ixzz24fVfq0Bx

Aug 26, 2012 | 2005 Chevrolet Tahoe

2 Answers

Obd code p0457 fuel cap replaced mil reset defect not cleared connection checked ok


The code is for a large leak in the EVAP system such as a loose or missing gas cap. But it could also mean a loose or missing hose to the canister or other leak in the tank.
The computer vents the tank several times an hour while the engine is running, and it checks the system by pressurizing the gas tank. If the tank will not hold pressure the code is set.
You may have to check the top of the tank where the fuel pump gasket is, as well as the vent lines to the front of the car.
A mechanic would perform a smoke test to look for leaks.

Jul 23, 2012 | Honda Accord Cars & Trucks

2 Answers

P1443 code problem. How do I fix this?


P1446 - EVAP Canister Vent Control Valve Close
EVAP canister vent control valve remains closed under specified driving conditions.

This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.

This solenoid valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows EVAP Control System (Small Leak) diagnosis.

The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

About the possible causes that your must solved:
- EVAP control system pressure sensor and the circuit
- Blocked rubber tube to EVAP canister vent control valve
- EVAP canister vent control valve
- Water separator
- EVAP canister is saturated with water


Hope this helps.

Apr 27, 2011 | Mercury Cougar Cars & Trucks

1 Answer

Po 442 po 455


P0442 - Evaporative Emissions System Leak Detected (Small Leak)

P0455 - Evaporative Emissions System Leak Detected (Gross Leak)

This diagnosis detects leaks in the EVAP purge line using engine intake manifold vacuum. If pressure does not increase, the ECM will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition. The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.

Causes:
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve
- Leak is in line between intake manifold

Solutions:
- Re-tighten or replace fuel tank filler cap
- Replace damaged or leaking EVAP canister
- Replace damaged or leaking lines.

Feb 10, 2011 | Chrysler Town and Country Cars & Trucks

2 Answers

Ford escort wagon 1997 code p1443 displayed. what does this indicate & where is the cannister? thank you.


P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

Possible Causes:
  • Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.
  • Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.
  • Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.
  • EVAP canister purge valve stuck closed (mechanically).

  • Possible Solution:
    Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

    The canister is on the passengers side near the firewall if I recall correctly.

    Jan 18, 2011 | Ford Escort Cars & Trucks

    2 Answers

    Code says evaporator purge solenoid


    Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

    P0440 Evaporative emission (EVAP) system - malfunction

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0441 Evaporative emission (EVAP) system - incorrect flow detected

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0442 Evaporative emission (EVAP) system - small leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

    Possible causes: Wiring, EVAP canister purge valve, ECM


    P0444 Evaporative emission (EVAP) canister purge valve -open circuit

    Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


    P0445 Evaporative emission (EVAP) canister purge valve -short circuit

    Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


    P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

    Possible causes: Wiring, EVAP pressure sensor, ECM


    P0455 Evaporative emission (EVAP) system - large leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0456 Evaporative emission system - very small leak detected

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


    P0457 Evaporative emission system - leak detected (fuel cap loose/off)

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


    P0458 Evaporative emission system, purge control valve -circuit low

    Possible causes: Wiring short to earth, EVAP valve


    P0459 Evaporative emission system, purge control valve -circuit high
    Possible causes: Wiring short to positive, EVAP valve


    Evaporative Emission Purge Solenoid

    Description & Operation
    The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
    During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
    The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
    Removal & Installation
    The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

    1. Disconnect electrical connector at solenoid.
    2. Disconnect vacuum lines at solenoid.
    3. Lift solenoid slot from mounting bracket for Removal & Installation.

    To Install:
    1. Position solenoid slot to mounting bracket.
    2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
    3. Connect electrical connector to solenoid.
    Purge solenoid location:

    jturcotte_65.gif
    EVAP cannister location:
    jturcotte_66.gif

    Nov 05, 2010 | 2000 Jeep Grand Cherokee

    2 Answers

    Question regarding a honda odyssey 1999 check engine light codes.


    Ramon
    P0420 relates to the catalytic converter. The computer sees little or no improvement in the exhaust before and after going through the converter. Either your oxygen sensors need replacement (3 total) or you need a new catalytic converter.
    What is the mileage on the vehicle? Does it run well? Oxygen sensors generally start to fail after 70,000 miles. Catalytic converters usually fail because the engine is runnig rich and the owner ignores that fault for months. This causes the catalytic converter to overheat and fail.

    P1456 relates to the evaporative emission system. This system holds the gas fumes in the system so they are not vented to the atmosphere. The most common cause of this code being set is failing to properly tighten the gas cap after refueling. Take the cap off and clean the sealing O-ring. Put it back on and tighten till it clicks 3 times. Make sure you have the correct gray colored gas cap. Clear the code and see if it resets within a few days. If it does, try replacing the gas cap.
    Charlie

    Jun 26, 2008 | 1999 Honda Odyssey

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    451 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    77202 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...