Question about 1995 GMC Sierra C1500

Open Question

WHICH FUSE POWERS THE O2 SENSOR ON A 1996 GMC 1500?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: 1996 gmc 1500 v6 has on spark

there are 3 solutions, 1, the distrubter, 2 spark plug wires, 3 power supplie to the coil pack (as in the wiring harnis )

Posted on Jan 25, 2009

daves944
  • 1050 Answers

SOURCE: 02 sensors not ready

The code P0420 indicates that the catalytic converter is not functioning efficiently. This could be because the cat is damaged or the engine is not running very well and the cat cannot keep up with the emissions. You should ensure that the spark plugs and ignition components are in top shape before replacing anything else. If a compression check reveals a low cylinder, you will not be able to prevent this code as even a new cat cannot keep up with a dead miss. If the state of tune and the compression is good, then you'll likely need a cat.

I've posted the drive cycle just so you know what to do when you have resolved the code.

  1. Cold Start. In order to be classified as a cold start the engine coolant temperature must be below 122°F (50°C) and within 11°F (6°C) of the ambient air temperature at startup.
    Do not leave the key in prior to the cold start or the heated oxygen sensor diagnostic may not run.
  2. Idle. The engine must be run for two and a half minutes with the air conditioner on and rear defroster on. The more electrical load you can apply the better. This will test the O2 heater, Passive Air, Purge "No Flow", Misfire, and - if closed loop is achieved- Fuel Trim.
  3. Accelerate. Turn off the air conditioner and all the other loads and apply half throttle until 55mph (88km/hr) is reached. During this time the Misfire, Fuel Trim, and Purge Flow diagnostics will be performed.
  4. Hold Steady Speed. Hold a steady speed of 55mph (88km/hr) for 3 minutes. During this time the O2 response, air Intrusive, EGR, Purge, Misfire, and Fuel Trim diagnostics will be performed.
  5. Decelerate. Let off the accelerator pedal. Do not shift, touch the brake or clutch. It is important to let the vehicle coast along gradually slowing down to 20 mph (32km/hr). During this time the EGR, Purge and Fuel Trim diagnostics will be performed.
  6. Accelerate. Accelerate at 3/4 throttle until 55-60mph (88-96 km/hr). This will perform the same diagnostics as in step 3.
  7. Hold Steady Speed. Hold a steady speed of 55mph (88km/hr) for five minutes. During this time, in addition to the diagnostics performed in step 4, the catalyst monitor diagnostics will be performed. If the catalyst is marginal or the battery has been disconnected, it may take 5 complete driving cycles to determine the state of the catalyst.
  8. Decelerate. This will perform the same diagnostics as in step 5. Again, don't press the clutch or brakes or shift gears.

Posted on May 14, 2009

  • 56 Answers

SOURCE: what fuse controls power seat for 1996 gmc 1500 travelquest

the best place to look is actually on the back of the fuse cover it should have a diagram of the fuses and say what each fuse goes to and what size fuse it is

Posted on May 14, 2009

  • 62 Answers

SOURCE: blower motor resistor location on a 1996 gmc 1500?

It is located on top of the heater box in the passenger side remove the glove box to gain acess there are two 7mm srews and a relay braket holding it in place it is a tight squeeze but can be removed with a 1/4 inch ratchet.

Posted on Aug 01, 2009

mikes112
  • 56 Answers

SOURCE: 1991 gmc 1500 blower motor doesnt work

I had to change the blower motor, turns out the spring tension on the brushes on the motor were too tight and ate into the brass commutator of my old motor.

Posted on Sep 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is bank 1 sensor 1 at on a 1996 gmc yukon 5.7v8?


Bank 1 is driver's side. O2 sensor 1 is before cat converter, O2 sensor 2 is after converter. #1 should be in the downpipe from the exhaust manifold.

Feb 18, 2015 | GMC Cars & Trucks

1 Answer

Hi i have code po161 for a 2004 gmc sierra 5.3 is it front o2 or the back o2.


Code P0161 indicates a problem with the heater circuit of O2 sensor #2 on bank #2

Apr 19, 2011 | 2003 GMC Sierra 1500

2 Answers

Reading codes 13 and 32 smelles of gas 1992 gmc sierra 1500 k-model 350ci


13 is an O2 sensor circuit issue, 32 is the EGR-OBDI is not as precise as OBD!! but you should see if your egr is hooked up, or if there is a blown fuse for it-the O2 sensor might just be due for replacement, you could try to clean the codes first (disconnect the neg cable for 10 minutes) to see if they come back right away.

While you are checking things, make sure the fuel pressure regulator is not leaking or has gas in the vacuum hose that connects to it.

Apr 02, 2011 | GMC K1500 Cars & Trucks

1 Answer

What fuse controls power seat for 1996 gmc 1500 travelquest


the best place to look is actually on the back of the fuse cover it should have a diagram of the fuses and say what each fuse goes to and what size fuse it is

May 14, 2009 | 1996 GMC Sierra

1 Answer

Location of O2 Sensors on 1996 Dodge Ram 1500 ?


Follow your exhaust manifold down from engine to exhaust pipes etc, you should see them sticking out, 3"-4" approx.length, with wires coming from them. Some are right on manifold, some further down on exhaust pipes.

Apr 15, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

O2 sensor 1996 volvo fail emission test


There is a slight possibility if the fault for the O2 sensor heater element, which is powered through a separate fuse, but it's unlikely.

Jan 03, 2009 | 1996 Volvo 960

1 Answer

Sensors


Band 2 stands for the pass. side of the engine. Sensor 1 is the O2 sensor closest to the engine.

Jun 13, 2008 | 1996 GMC Jimmy

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...