Question about Toyota Cars & Trucks

Open Question

Removal rear door trim 2007 prado

Have unclipped but cannot get top part at window lift away

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: How to remove trim from rear hatch door on 2001 Sienna

You need to remove the big plastic or vinyl rear hatch trim to get the side trims off. Remove the 10 mm bolt that holds the pull handle (if you have a pull handle), and then, using a flat tool, (like a stiff putty knife), insert the tool between the vinyl trim and the tailgate to loosen the plastic clips (there is like 18 of them); one the hatch panel is off, you will see that you can now remove the side trims.

Posted on Oct 27, 2008

Ad
  • 2 Answers

SOURCE: How do you remove the upper wood trim panel on the left rear door

If you mean the one by the air vents it just pulls off

Posted on Jan 07, 2009

  • 184 Answers

SOURCE: Remove Rover 45 driver door trim to replce wing mirror.

what you need to do here is pull out door trim from bottom & then give it a good bang at bottom it should slide out of top guide but you need to give it a good bang asthey are quite tight in there.

Posted on Mar 12, 2009

michigan man
  • 3533 Answers

SOURCE: Removal of rear door trim panel

try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 21, 2009

  • 316 Answers

SOURCE: Interior trim panel removal instruction

Normal 0 . Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.


If you don't have power windows you will have to remove the manual window crank. It is held in place by a clip on the back side of the base. To remove the clip, you will need a small hook (kind of like a knitting needle). Put the hook in behind the base, and grab the clip and pull it off. To replace it, slide the clip back on the window crank, and snap it back on the door.

Posted on May 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the Drivers side door panel on a 2007 GMC Acadia


remove any blanking plugs in door trim at arm rest and handles. Remove the window winder . Using a flat blade insert between the door trim and the door and twist until the retainers jump out Repeat all the way around the door. With the glass all the way down lift up the trim and push outwards at the top and it will lift away

Nov 09, 2013 | 2008 GMC Acadia

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.


Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal
  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.


    r11176a.gif

Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse order.


    Liftgate


    r10441a.gif

2010&c18=modelyear&c35=wsm%2ctrim%20panel%2c%20door%2csww%2c01-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1998 Ford Windstar

1 Answer

How do you remove a rear door panel on an Audi A3 4 Door


802771-a4_door_card_rear.gif

- Door trim.
Removal
- Unclip decorative panel -2-.
- Remove decorative panel -2- toward front.
- Remove bolts -3- (3x) from door trim -1-.
For vehicles with electric window regulators
- Window regulator switch, removing and installing Page 70-25 .
For vehicles with manual window crank
- Manual window crank, removing and installing Page 70-26 .
For all vehicles
- Unclip door trim -1-. Replace damaged clips Fig. 3
- Raise door trim -1- upward approx. 20 cm. out from door shell.
- Disengage Bowden cable for interior door mechanism Fig. 1 .
- Disconnect electrical harness connectors Fig. 2

Dec 03, 2010 | 2005 Audi A3

2 Answers

Removing/installing 2000 dodge grand caravan window glass


after u remove the bolts that hold it to the window regulator tip the window towards the front of the door and the top rear corner of the window should pop out and then u just lift hte window out,hope this helps

Sep 05, 2009 | 2004 Dodge Caravan

1 Answer

Need to remove drivers door panel


please rate if this helps. Section 01-05: Trim, Interior 1995 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION The interior trim component Removal and Installation procedures generally apply to all models. If some of the steps do not apply to the particular models being serviced, proceed to the next step. Trim Panels, Door Removal and Installation
  1. ssd~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not pry front door trim panel (23942). Prying on front door trim panel will break the hook retainers.
    Disconnect battery ground cable (14301) .
  1. Carefully pull front door trim panel finish panel (23712) away from front door trim panel .



    9e3f506.gif
Item Part Number Description 1 23713 Front Door Trim Panel Finish Panel 2 17B676 Outside Rear View Mirror Control 3 14028 Door Lock Switch 4 55928-S55 Screw (5 Req'd) 5 14529 Window Regulator Control Switch 6 23942 Front Door Trim Panel
  1. Disconnect wires from front door lock switches (14017), outside rear view mirror controls (17B676) and window regulator control switches (14529) , if equipped; remove front door trim panel finish panel.
  1. Remove front door trim panel retaining screw through front door trim panel finish panel opening.

    Trim Panels, Door


    83b257f.gif


    Item Part Number Description 1 20124 Front Door 2 23942 Front Door Trim Panel 3 383356-S100 Nut (2 Req'd Each Side) 4 56903-S58 Screw (2 Req'd Each Side)
  1. Remove interior lamp lens cover.
  1. Remove screw through interior lamp opening.
  1. Slide front door trim panel upward to disengage hooks.
  1. Rotate top of front door trim panel away from front door (20125) , and lift bottom hooks from front door.
  1. Disconnect window regulator jumper wire (14A630) .
  1. Remove front door trim panel.
  1. To install, reverse Removal procedure.

May 07, 2009 | 1994 Mercury Cougar

1 Answer

Door panel


here is a diagram of how to unistall your door panel. please do not forget to rate and comment about your experience with fixya today.

Driver's Side Door
NOTE This procedure is for models with power windows. If equipped with manual windows, refer to the procedure for the Passenger Side Door Panel.


NOTE Do not grasp in grip depression when pulling off grip recess, as there is a strut secured to door trim underneath.

  1. If necessary, make sure you have the radio code.
  2. Make sure the ignition if OFF, then disconnect the negative battery cable.
  3. Insert a suitable prytool in lower partition between the panel and grip recess.
    42075_vwca_g0157.gif Insert a suitable prytool in lower partition between the panel (1) and grip recess (2)
  4. Unclip the grip recess upward out of door trim. Do NOT reach into grip depression while doing so, to prevent damage to brace.
  5. Press the locking lug against the connector (3 – arrow) and pull it off.
    42075_vwca_g0158.gif Unclip the grip recess (2) upward out of door trim. Do NOT reach into grip depression while doing so, to prevent damage to brace (1). Then , press the locking lug against the connector (3 – arrow) and pull it off
  6. Unscrew the 7 mounting bolts.
  7. Unclip the door trim at the sides using disassembly pliers 3392, or equivalent.
  8. Lift the door trim up out of window recess.
    42075_vwca_g0159.gif Unfasten the 7 bolts (arrows). Use pliers to unclip the door trim (1) at the sides, then lift the trim up out of the window recess
  9. Unclip the cable guide using a prytool, pull out the bracket in the direction of the arrow, then unhook the cable hook.
    42075_vwca_g0160.gif Unclip the cable guide (1) using a prytool (2), pull out the bracket (3) in the direction of the arrow, then unhook the cable hook (4)
  10. Disconnect the connectors and remove the trim panel from the vehicle.
    42075_vwca_g0162.gif View of the driver’s side door panel—with power windows
To install:
  1. Pull off the window recess seal from door trim and insert in window recess.
    42075_vwca_g0161.gif Pull off the window recess seal (1) from door trim and insert in window recess
  2. The remainder of installation is the reverse of the removal procedure, noting the following:
    • Before installing door trim, check all clips and replace as necessary, and insert into mounts of door trim.
    • After connecting battery, check that the vehicle equipment (radio, clock, electric windows) is operating properly.
    • If the Electronic Control Module (ECM) is subject to low voltage with ignition on, DTC memory and Readiness code must be checked with a scan tool.

Apr 13, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

Window regulator replacement


Window Regulator, Rear Door, Explorer Removal
  1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .
Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation
  1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.
  1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.
  1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .
  1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .
  1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.
  1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
    33c9359.gif
  1. If equipped with power windows, disconnect the wire from the regulator.
  1. Remove the rear door window glass as described in this section.
  1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.
  1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
  1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.
  1. Remove two upper regulator attaching nuts.
  1. Remove regulator from the front door (20125) .
Installation
  1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.
  1. Install regulator into access hole in inner panel.
  1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).
  1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).
  1. Install two upper regulator attachment nuts.
  1. Install door glass as outlined under Door Glass Installation.
  1. Adjust glass as outlined under Adjustments .
  1. Reconnect wire to regulator, if equipped.
  1. Check operation of window regulator.
  1. Install door watershield and trim panel. Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

How to remove the door panel on a 96 Ford Thunderbird?


Carefully pull front door trim panel finish panel away from front door trim panel.
Disconnect wires from front door lock switches, outside rear view mirror controls and window regulator control switches, if equipped. Remove front door trim panel finish panel.
Remove front door trim panel retaining screw through front door trim panel finish panel opening.
Remove interior lamp lens cover.
Remove screw through interior lamp opening.
Slide front door trim panel upward to disengage hooks.
Rotate top of front door trim panel away from front door and lift bottom hooks from front door.
Disconnect window regulator jumper wire
Remove front door trim panel.

Feb 21, 2009 | 1996 Ford Thunderbird LX

1 Answer

How do you remove the door panels on a 1995 mercury villager


http://autos.groups.yahoo.com/group/villagerquest/

you have to remove the cup behind the door handle. rmove screws aroun the door pull. get a screw driver and pry the trim panel away from the door carefully. There is a plastic christmas tree clip every 6 inches. when the bottom & sides are free, lift up the trim panel to get it out of the track at the base of the window.
--------------------------------------------------------------------------------------

Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).

  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connections.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.

Jan 04, 2009 | 1995 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

460 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...