Question about 2004 Jeep Grand Cherokee

Open Question

What are some signs of a bad front axle 2004 jeep grand cherokee

What are some signs of a bad front axel 2004 jeep grand cherokee

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2004 jeep gran cherokee front end clunk

you must replace and lube the front sway bar bushings,chrysler service bulletin calls it a squak, but can sound like a rubbing, a clunk etc the common factor is this is really noticeable the colder it gets outside

Posted on Mar 03, 2009

  • 1 Answer

SOURCE: windows and lock wont operate on a 2004 Jeep Grand Cherokee

I just had the same with mine, pull the rubber boot back on the drivers side front door and look for a severed wire, mine was black...simply spliced the wires back together and problem solved!

Posted on Mar 23, 2009

  • 52 Answers

SOURCE: Rear Axle Seal Replacement

remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.

Posted on Apr 22, 2009

  • 304 Answers

SOURCE: Rear Axel Seal Leaking, How do I pull the axel to repair?

You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

Posted on May 22, 2009

  • 94 Answers

SOURCE: 2004 Jeep Grand Cherokee. Keeps stalling, engine

P0505 means the whole Idle Control system, not only the IAM. Check all related sensors (i.e. crankshaft sensor). Check with a voltmeter direct at the connector of the IAM if you get any signal. Remove the IAM from the TB, connect him, let someone switch your ignition key to ON. The IAM need to drive in/out for a short time to find the right position. Hold the IAM near a hard part, that they cant drive out completely! If IAM works fine, check the fuel pressure, check and clean your TB ( if not done yet). If that doesn't work, come back again please

Posted on Oct 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil leak out of front left axel from the dif, on a jeep grand cherokee.


axle seal is bad take it to a dealer need special tools to do this

Sep 24, 2013 | 1995 Jeep Grand Cherokee

1 Answer

Can you conver front axel u joint type to a cv joint type on an 95 jeep grand charokee lorado


I owned a 93 GC 4x4 and I did replace my front axles with CV joint axles. The new axles came with CV joints, with a rubber boot and all so yes you can.

Sep 09, 2012 | 1995 Jeep Grand Cherokee

2 Answers

I have a 1997 Jeep Grand Cherokee, Im getting a rattle under the jeep. It sounds like metal hitting metal its not the exhaust for that is not hittig anything. it sounds like its to the rear. Someone said...


Your jeep has two upper and two lower control arms attached to the rear axle. They have rubber bushings where they bolt to the axle and to the body. If the bushings are badly deteriorated, you will get a metal to metal sound when hitting bumps. Have them all checked.

Jan 03, 2011 | 1997 Jeep Grand Cherokee

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Leaking rear axel seal


  1. Remove or disconnect the following:

    Rear wheel Brake caliper and rotor, if equipped Brake drum, if equipped Axle retainer nuts Axle shaft, seal and bearing assembly
  2. Split the bearing retainer with a chisel and remove the retainer ring.
  3. Press the bearing off the axle shaft.
  4. Remove the axle seal and retaining plate.
0900c15280220349.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Rear axle seal and bearing components-2002-05 exc. 2005 Grand Cherokee Hope this helps, please dont forget to rate my solution.



Lefty64

Apr 09, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Front axle


MAYBE THE BRAKE HOSE MAKING THE BRAKES STICK @HEATING UP THE ROTOR DOES IT PULL RT. OR LF? OR IS THE CV BOOT BROKEN?THE BURNT SMELL DOEN'T USUALLY HAPPEN WITH AN AXEL PROBLEM

Jan 24, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...