Question about 2003 Jaguar S-Type

Open Question

Code p1000 jaguar s type 2003 - 2003 Jaguar S-Type

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 52 Answers

SOURCE: need to know what a p1000 diagnostic code means for a jaguar s ty

Looks like you have acommunication problem with the computer, it is going in to safe mode. Check all computer connections before you go to jaguar.
I have attached a picture of the error code.
hope this helps61f0008.jpg

Posted on Jan 17, 2009

Ad
raygin
  • 322 Answers

SOURCE: how do i fix code po420 & po430 on 2003 jaguar

Both these codes relate to Catalyst efficiency below threshold on banks 1+2. This is normally caused by a combustion fault. This fault may be shown due to a faulty sensor in either air imput or exhaust systems, Get the memory read at a dealers or good garage. If you had a serious problem the car would not drive well.
Hope this helps - good luck.

Posted on May 12, 2009

SOURCE: Have error codes C1175 &

C1175 ABS/TCCM Anti-lock braking / traction control LH rear wheel speed sensor circuit fault ABS/TCCM to wheel speed sensor signal circuit (FH33-21): open circuit, short circuit to ground, short circuit to B+ voltage, high resistance LH rear wheel speed sensor failure
P1000 is for check not complete after last memory clear , dont worry about it , just stick with C1175 , and most probably it is the sensor wire

Posted on Aug 13, 2009

  • 3600 Answers

SOURCE: can you tell me what these two codes are P1000 and

Po code 1000 is system readyness test, it means it has not met all condtions or flags since last reset of the computer. and the other C1165-Wheel speed sensor circuit right rear electrical failure and C1235-Wheel speed sensor circuit right rear signal failure
Possible Source(s):

  • Harness fault.
  • Connector loose or corroded.
  • Connector pin(s) bent or tracking between connections.
  • Sensor gap incorrect.
  • Foreign matter on sensor face.
  • Missing tooth on sensor wheel.
  • Faulty Sensor.
  • Most Likey cause the harness got knocked off the sensor. If you need more help let me know.

Posted on Sep 21, 2009

  • 279 Answers

SOURCE: my 2002 jaguar x type 3.0 has the p1000 code when

P1000 is an indication that the self diagnosis was not compleated for some reason. This code will clear, if there are no other problems and the test compleates. The test normally requires about 25- 50 miles of steady driving at speeds below 50 mph. please see www.bluejag.co.uk for more information on fault codes

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 jaguar x tipe code P1000


this code relates to monitoring the ECU self test , meaning it was'nt completed , have the code cleared , are there any problems with the vehicles performance or just the CEL on ? follow this link and you can run the self test your self to see if that sorts the prob
Jaguar Type Instrument Cluster Diagnostic codes

Apr 25, 2014 | 2002 Jaguar X-Type

1 Answer

2003 jaguar s type code p1000 and c1165


the p1000 is a system readiness code meaning the car is checking itself..it means its not finished etc but once it has the code will change to p1111..meaning system check completed, the c1165 is a abs or wheel speed code, check the wheel where this code is originating

Apr 03, 2014 | 2003 Jaguar S-Type

1 Answer

I have a 2003 jaguar x-type awd but i been having the code p1000 i been driving my car for more than 200miles and i cant get any monitor to be reset as ready and im not able to pass my emission test c


code p1000 refers to system readiness test not complete. There are no causes for this listed so the problem will be in the CPU program that is not progressing through the tests that it does after starting the car. Possible way to overcome this is to use a scanner to reset the program as it is obviously corrupted compare this problem to a PC that turns on and before starting the task bar stops in a loop that says installing settings.

Mar 21, 2014 | Jaguar X-Type Cars & Trucks

1 Answer

P1000 code in 2005 jaguar xtype


that code is always in there it means security system check complete.and is not a cause for concern its to with the anti theft system

Mar 29, 2013 | 2003 Jaguar X-Type

1 Answer

Wats the code p1000 on my 2002 jaguar x type


P1000 JAGUAR - On Board Diagnostic System Readiness Test Not Complete, this is known as the OBD2 drive cycle.


Possible causes - The vehicle is new from the factory.
- Battery or Powertrain Control Module (PCM) had recently been disconnected.
- An OBD monitor failure occurred before completion of an OBD drive cycle.
- PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool.
When is the code detected? If DTC P1000 is triggered after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles have not been cleared. P1000 JAGUAR Description The On Board Diagnostic (OBD) monitors are performed during the OBD Drive Cycle. P1000 is stored in continuous memory if any of the OBD monitors do not carry out their full diagnostic check.

Feb 18, 2011 | 1999 Jaguar XK8

1 Answer

Ihave a 2003 Jaguar S-Type, What do PO133, PO153 and P1000 codes mean? Afriend said oxygen sensors; how to change the oxygen sensor for a 2003 Jaguar S-Type?


You might check this site out for Jag codes. Oxygen sensors can be a sticky job, they're screwed into exhaust and can literally weld themselves in place. Plus in most cases you need special wrench/socket to get around the sensor. (they can be a real pain)

http://www.obd-codes.com/

Jan 04, 2011 | 2003 Jaguar S-Type

1 Answer

2003 jaguar s type what does p 1000 code mean


If the Dianosis test Code P1000 is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE NOT BEEN COMPLETED. See http://www.bluejag.co.uk for further details on this

May 13, 2010 | 2004 Jaguar S Type

3 Answers

What dose the code p1000 mean and p1645


P1645 EVAP Solenoid Output Circuit
P1000 Scan not complete. meaning it didnt finish scanning

Sep 14, 2009 | 2002 Jaguar X-Type

1 Answer

04 jaguar x type sport premium diesel air bag light on. on start up the air bag light flashes up , then after approx 30 seconds it stays on , could this be a faulty sensor ??? or some thing more sinister?...


When the air bag light flashes it is actually doing what is called a "flash code" which can be read by your dealer.The P1000 code is only a standard check code in the Engine control module,The DTC (diagnostic trouble code) will be in the restraints system and the flash codes need to read too...It will flash when igntion is on...will flash then stop a second then flash again giving a 2 digit flash code,then diagnosing can begin

Nov 21, 2008 | 2003 Jaguar X-Type

Not finding what you are looking for?
2003 Jaguar S-Type Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...