Question about Chevrolet Spark

1 Answer

Torque settings for cylinder head for chevvy spark 1.0L

1.0L 2006 model

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,754 Answers

I found this info. Note, these databases are not always correct, but, it's all I have.
torque settings for cylinder head for chevvy spark - 11619153-rg1ef4lamymlkzrkneh4f044-4-0.jpg

11619153-rg1ef4lamymlkzrkneh4f044-4-2.jpg

Posted on Jun 16, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

  • 496 Answers

SOURCE: I need the torque settings

cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Posted on Feb 22, 2011

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

sirgabe51
  • 66 Answers

SOURCE: I have 4.9L6 need torque specs for cylinder head

for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


e023442.jpg

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings head bolt hyundai 2.2 crdi 2006


is your motors head torques listed on

also has torque sequence page number reference layouts are bottom of the document

page 33 as a pdf

or page 50 of paper listings

http://olybrake.com/pdf/fel_pro_torque_specs_guide.pdf

May 11, 2016 | Hyundai Santa Fe Cars & Trucks

2 Answers

Please assist with Cylinder Head Torque and Valve Clearance Specs for Tata Indica 1.4 LXi


i need the head talk settings & valve clearance for tata indica lxi

Apr 20, 2013 | 2006 Tata Indica LXi

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    1 Answer

    How to change the spark plugs on peugeot 406 v6 3l coupe is this straight forward like a 4 cylinder car


    1. Spark plugs removal

    1.1. Front cylinder bank spark plugs removal:
    1.1.1. Disconnect the battery from car terminals.
    1.1.2. Remove the engine plastic cover.
    1.1.3. Disconnect the ignition coils electrical supply cable and all three coils connectors.
    1.1.4. Remove all three ignition coils screws.
    1.1.5. Remove all three ignition coils out from cylinder head.
    1.1.6. Remove all three spark plugs out from cylinder head (straight forward).

    1.2. Back cylinder head bank spark plugs removal:
    1.2.1. Remove the inlet manifold out from cylinder head.
    1.2.2. Disconnect all three ignition coils connectors.
    1.2.3. Remove all three ignition coils screws.
    1.2.4. Remove all three ignition coils out from cylinder head.
    1.2.5. Remove all three spark plugs out from cylinder head (straight forward).

    2. Spark plugs installation

    2.1. Refit all in reverse order.
    2.2. Spark plugs tightening torque = 2,8 +/- 0,3 daN.m
    2.3. Ignition coils tightening torque = 0,8 +/- 0,2 daN.m

    Nov 16, 2010 | 2005 Peugeot 405

    2 Answers

    Head gasket torque specifications and sequense


    Please don't forget to rate. Thank you:

    Left side front cylinder head


    98e175a.gif
    Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    2 Answers

    Torque setting cylinder head bolt 4 cylinder KIA sportage


    I need the torque settings and pattern for a Kia Sportage 2.2

    Nov 24, 2009 | 2001 Kia Sportage

    2 Answers

    What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


    Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

    1. Disconnect the negative battery cable.
    2. Drain the cooling system.
    3. Disconnect the hoses at the thermostat housing.
    4. Properly relieve the fuel system pressure.
    5. Remove the cylinder head cover.
    6. Loosen the rocker arms.
    7. Remove the pushrods.

    The valvetrain components must be replaced in their original positions.
    1. Remove the intake and exhaust manifold from the cylinder head.
    2. Disconnect the spark plug wires and remove the spark plugs.
    3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
    4. Remove the accessory drive belt(s).
    5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
    6. Remove the intake and exhaust manifold assembly.
    7. If equipped with A/C, perform the following:
      1. Remove the compressor and position it aside with the lines attached.
      2. Remove the compressor bracket bolts from the cylinder head.
      3. Loosen the through bolt at the bottom of the bracket.

    8. Remove the alternator.
    9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

    Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
    1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
    2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

    To install:
    1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

    Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

    Oct 08, 2009 | 1998 Jeep Cherokee

    3 Answers

    Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


    BMW cylinder torque setting all models

    According to my service manual as follows.

    Cyl head to engine block (torx e12 M10 bolts)

    Stage 1 30nm (22 ft – lb)
    Stage 2 + 90 degrees
    Stage 3 + 90 degrees

    Cyl head to lower timing chain cover 10nm (89in – lb)

    The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

    Jun 16, 2008 | 1992 BMW 3 Series

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    972 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...