Question about 2006 Chevrolet Impala

Open Question

Why does my 2006 Chevrolet Impala's bcm fuse keep blowing and then it will say service air bag?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ndguy2481
  • 251 Answers

SOURCE: 2006 chvy impala when idling dont blow hot air

1 Inspect Cooling System Mix Coolant level low or flow is restricted. grey_line.gif 2 Inspect Thermostat Thermostat stuck closed grey_line.gif 3 Inspect Heater Control Valve Leaking or defective heater control valve. here something to help u

Here to help Shaun

Posted on Nov 23, 2008

Ad
trackrash
  • 10 Answers

SOURCE: turning off the air bag chevrolet kalos

Are you talking about the passenger side? They sometimes have a switch to turn them off. The drivers side does not have an on off switch. Be careful working around air bags they can KILL YOU.

Posted on Jun 17, 2009

  • 71 Answers

SOURCE: chevy silverado 2006 lights "service air bag"

First of all you need to get this problem fixed ASAP. While the airbag light is illuminated, your SDM (Sensing and Diagnostic Module aka: the brain of your airbag system) shuts of power to the airbags. In which, if you are in an accident your airbags will not deploy while this light is illuminated. You need to take your vehicle to a GM dealership. A Tech 2 scantool is needed to retrieve the code from the SDM. Hopefully it won't be a costly repair, but is something that defineatly needs to be corrected soon. Good luck and hope all works well.

Posted on Jul 04, 2009

Testimonial: "very fast and helpful, thanks"

  • 124 Answers

SOURCE: Problem with 2006 Chevrolet Impala --Windshield washer fluid

Sounds like the fuse blew out again. Look at the wiring that goes to the washer fluid pump and check for any place where it might have rubbed against something causing it to short out. Fix this 'short' before you replace the fuse again or you will continue to have problems.

Posted on Nov 05, 2009

  • 1 Answer

SOURCE: i need a serpentine belt assembly guide or diagram for a 2006 3.5 liter v6 chevrolet impala

Diagram 9-5 on this page:
http://www.daycoproducts.com/daycoweb.nsf/Serp%20Rout%20Guide%20Illus.pdf

Posted on Nov 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 chevy impala door locks do not operate


Do you know anything about body electronics , BCM - body control module ? The door lock switches are control inputs to the BCM .The BCM will energize relays in the I/P fuse block to lock or unlock the doors . Check out wiring diagrams here http://www.bbbind.com/free_tsb.html Enter your vehicle info. Year , make , model and engine size . Under system click on Body & Accessories . Then under subsystem click on power locks . Do the power windows work ? .There maybe codes stored in the BCM . your best bet mite be to take it to the dealer .

Apr 12, 2017 | 2006 Chevrolet Impala

1 Answer

How do I fix the horn on 2006 Impala


System Description
The horn PCB relay is non replaceable ,soldered to the underhood fuse / relay box. . You would have to take the box a part to get at it . Is the air bag light lit on the instrument cluster ? Could have an open wire in the Clock spring , do you know what a clock spring is ? It is inside the upper part of the steering column , It allows the steering wheel to be turned full right to full left keeping the horn an all the buttons an air bag connected electrically. When the horn button is pressed, ground is applied through the horn switch contacts and the horn relay control circuit to the coil side of the relay. The horn relay coil is then energized, causing the relay switch contacts to close applying voltage through the horn control circuit to the horns. For theft deterrent functions, the body control module (BCM) also controls the horn relay by applying ground to the relay control circuit to the relay.
Circuit/System Testing
With a test lamp connected to ground, probe each of the test points on the HORN fuse while activating the horns. The test lamp should illuminate at one or both of the fuse test points.
?‡'
If the test lamp does not illuminate at either test point, refer to the Horn Switch Test.


?‡'
If the test lamp illuminates, refer to the Horn Test.


Ignition OFF, disconnect the inline harness connector C275. Ignition ON, test for B+ between the horn relay control circuit terminal B and ground.
?‡'
If less than B+, test the control circuit for an open/high resistance. If the circuit tests normal, replace the underhood fuse block.

Momentarily connect a 3-A fused jumper wire between the control circuit terminal B and ground. The horns should work.
?‡'
If the horns do not work, replace the underhood fuse block.

If all circuits test normal, test or replace the horn switch

The PCB relay horn system consists of the following components:
?€¢
Horn switch

?€¢
Horn PCB relay

?€¢
Horn assembly

?€¢
Body control module (BCM)

?€¢
HORN fuse 15 A

How cars clock spring works

May 17, 2016 | 2006 Chevrolet Impala

1 Answer

I have a 2006 Impala the 10 amp a/c fuse blows. I was told by ask.com i needed a new compressor. So i put one in and still have the same problem.


I would start by checking the wiring from the a/c control head all the way to the compressor as it is most likely a short causing the fuse to blow. You will most likely need a wiring schematic of the air conditioning system and a dvom/volt meter.

Sep 12, 2013 | 2006 Chevrolet Impala

1 Answer

Multiple electrical problems starting with airbag light


air bag code,batt. drain with ampmeter,dome lamp short too ground,all ground connexion check voltage drop,

Aug 03, 2013 | 2006 Chevrolet Aveo

1 Answer

Blowing A/C fuzes


Well the short answer is too much current flowing thru the circuit. It would depend on what the fuse controls as to where the problem is. Could be a component or a wiring problem, including a short to ground.

Jul 03, 2013 | 2006 Chevrolet Impala

1 Answer

2002 Chevy Malibu where and which fuses are for the BCM. Where can I get a BCM schemtic or wiring diagram


The BCM receives power from the 10A IPC/BFC ACC FUSE J and 10A BFC BATT FUSE F in the left I/P fuse block, 10A A/C BFC FUSE 37 in the underhood fuse block, and 10A CRUISE FUSE 8 and 10A INT LPS FUSE A in the right I/P fuse block

Nov 17, 2012 | 2002 Chevrolet Malibu

1 Answer

Describe why my air bag light keeps blinking on and off i have a 2005 chevy impala


You have a condition the computer recognises as a fault in the air bag system. It needs to be corrected to have the air bag system work properly. A Scanner with Air Bag ability needs to be used to diagnose the problem. First look for any blown fuses for the air bag system.

Sep 24, 2009 | 2000 Chevrolet Venture

2 Answers

Security System


Several GM products, including the Chevrolet Impala and Malibu, the Oldsmobile Alero, the Pontiac Grand Prix, and Saturn Ion, have issues with the Security light coming on. This is many times an indication of a failing Body Control Module (BCM). Initially, the Security light will come on then go off, progressing to a constant on light, before the car will refuse to start. Other symptoms may include erratic action of electronics, a clicking sound coming from the glove box, and the air conditioning failing to blow cold air. I recommend a shop that specializes in the electronic systems of vehicles to diagnosis and make the necessary repairs. They should keep the car until they replicate the symptoms described. A new BCM from GM should cost about $230; plan on another $200 for them to diagnose the problem, replace the unit, and program the new unit. The dealers quote between $700 and $1,100 for the same repair. My experience and the experiences I have read on the internet, indicate the new BCM should last only about a year.

Jun 24, 2009 | 2003 Chevrolet Impala

1 Answer

2004 impala 3.4


Several GM products, including the Chevrolet Impala and Malibu, the Oldsmobile Alero, the Pontiac Grand Prix, and Saturn Ion, have issues with the Security light coming on. This is many times an indication of a failing Body Control Module (BCM). Initially, the Security light will come on then go off, progressing to a constant on light, before the car will refuse to start. Other symptoms may include erratic action of electronics, a clicking sound coming from the glove box, and the air conditioning failing to blow cold air. I recommend a shop that specializes in the electronic systems of vehicles to diagnosis and make the necessary repairs. They should keep the car until they replicate the symptoms described. A new BCM from GM should cost about $230; plan on another $200 for them to diagnose the problem, replace the unit, and program the new unit. The dealers quote between $700 and $1,100 for the same repair. My experience and the experiences I have read on the internet, indicate the new BCM should last only about a year.

Jul 02, 2008 | 2004 Chevrolet Impala

Not finding what you are looking for?
2006 Chevrolet Impala Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...