Question about Cars & Trucks

Open Question

How to do valve and injector pump timing - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bleed a diesel pump jeep Cherokee turbo diesel 3.1 5 cylinder 2001


we dont have this engine here, USA.
but i have the WG jeep book,
starting page 12 , chapter 14


FUEL INJECTION PUMP BLEEDING
(1) If the fuel injection pump has been replaced,
air should be bled at the overflow valve before
attempting to start engine.
(a) Loosen the overflow valve (Fig. 18) at the
rear of the injection pump.
(b) Place a towel below the valve.
WARNING: WHEN CRANKING THE ENGINE TO
BLEED AIR FROM THE INJECTION PUMP, THE
ENGINE MAY START. PLACE THE TRANSMISSION
IN NEUTRAL OR PARK AND SET PARKING BRAKE
BEFORE ENGAGING THE STARTER MOTOR.
CAUTION: Do not engage the starter motor for
more than 30 seconds at a time. Allow 2 minutes
between cranking intervals.
(2) Crank the engine for 30 seconds at a time to
allow air trapped in the injection pump to vent out
the fuel injector drain tubes. Continue this procedure
until the engine starts. Observe the previous WARNING
and CAUTION.
(3) Tighten overflow valve.
HIGH-PRESSURE FUEL LINE BLEEDING
WARNING: THE INJECTION PUMP SUPPLIES HIGH-
-PRESSURE FUEL OF APPROXIMATELY 45,000 KPA
(6,526 PSI) TO EACH INDIVIDUAL INJECTOR
THROUGH THE HIGH-PRESSURE LINES. FUEL
UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE
THE SKIN AND CAUSE PERSONAL INJURY.
WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE
CLOTHING AND AVOID CONTACT WITH
FUEL SPRAY WHEN BLEEDING HIGH-PRESSURE
FUEL LINES.
WARNING: DO NOT BLEED AIR FROM THE FUEL
SYSTEM OF A HOT ENGINE. DO NOT ALLOW FUEL
TO SPRAY ONTO THE EXHAUST MANIFOLD WHEN
BLEEDING AIR FROM THE FUEL SYSTEM.
Bleed air from one injector at time.
(1) Loosen the high-pressure fuel line fitting at
the injector (Fig. 19).
(2) Crank the engine until all air has been bled
from the line. Do not operate the starter motor
for longer than 30 seconds. Wait 2 minutes
between cranking intervals.
(3) Start the engine and bleed one injector at a
time until the engine runs smoothly.

end quote.
pump timing is on next page
or tank filter line priming before. above.

Mar 22, 2016 | Jeep Cars & Trucks

1 Answer

Idle fine, then run ok for few minutes, then cant go over 15 mph,new filter, new supply pump, suspect turbo or injector pump


Hi , you probably have water that's went from the tank to the pump. DIESEL PUMP. The worst thing that you can do is let your fuel go way down low and some water is taken in with fuel + water . The fuel pump is a mechanical pump with moving parts and you can't let water in . Certain pumps ,diesel pumps have a latch valve and you don't want water to sit for any length of time in the surrounding wall of the valve as it will rust this may cause the valve to stick then your car may go to rev excessive sometimes high revs , i mean screaming rev's. Please get the pump checked.

Dec 27, 2015 | Cars & Trucks

1 Answer

Where is the air injector pump on a 2000 Montero Sport?


there is no air injector pump on your vehicles Vehicle Emission Control Information sticker (VECI) there are fuel injectors and evapoative canister, oxygen sensors and egr valve, egr vacuum control valve, manifold absolute pressure sensor, and a pcv valve and some other usual sensors hope this helps

Aug 05, 2014 | 2000 Mitsubishi Montero Sport

1 Answer

Why my 1998 gmc 15oo 4.2 v6 truck after warms up injectors stop pumping fuel


The pick up in the distributor is what tells the ECU to fire the injectors, would be a likely culprit.

Aug 05, 2014 | 1992 GMC Sierra K1500

1 Answer

I have a 2c toyota diesel turbo engine i put other valve and new valveseals the timing is correct and dieselpump is correct but the car don't want to start pls help


first check the valve clearance .0.15 inlet, and .025 exhaust. make sure valve timing and pump timing is correct.and check while cranking diesal is pump to the injector

Dec 21, 2013 | Cars & Trucks

1 Answer

HI,I have an Opel Combo Year 2000,.The engine does not start at all,trying to repair by different mechanics without sucess.it simply does not start though the fuel pump and valves has been serviced.


If the pump has been removed for servicing then I would say that the pump injector timing is off. It has to be set on injection mark and not tdc.. Have a professional injector mechanic check the timing.

Apr 23, 2013 | Opel Combo Cars & Trucks

2 Answers

95' Honda Civic 1.6 liter, will crank but wont stay running. Distributer, rotar, wires and plugs, fuel Filter and fuel pump have been replaced. We have been able to get the car running on occassions after...


i have a 95 honda civic and it will crank but not start, ive heard they have a common fuel pump relay problem so i bought a new 1 and also a new fuel pump but yet still the car will not start. we i turn the key the fuel pump does not engage and am stumped. ive checked all the fuses but there all good. any ideas please help . thanks

Oct 28, 2010 | 1995 Honda Civic

2 Answers

Fuel pours into cylinders


very strange and rare problem. something is keping the injectors open instead of pulsing them. The command to ground the injectors comes from the PCM, Powertrain Control Module. It may be a good idea to pick up a used one from a salvage yard. car-part.com is a good place to look. You will need the info off your module to match up.
Do you have 2.0L SPI engine or 2.0L Zetec engine?
Look on the page with the * to find the lowest price part.
aso, check for shorted wire going to injectors
---------------------------------------------

Mechanical Returnless Fuel System The fuel system consists of a fuel tank with reservoir, fuel pump, fuel pressure regulator, fuel filter, fuel supply line, fuel rail, fuel rail pulse damper, fuel injectors, and schrader/pressure test point. Operation of the system is as follows (Figure 62):
  1. The fuel delivery system is enabled during crank or running mode once the PCM receives a crankshaft position (CKP) sensor signal.
  1. The fuel pump logic is defined in the fuel system control strategy and is executed by the PCM.
  1. The PCM grounds the fuel pump relay, which provides VPWR to the fuel pump.
  1. The inertia fuel shut-off (IFS) switch is used to de-energize the fuel delivery secondary circuit in the event of collision. The IFS switch is a safety device that should only be reset after a thorough inspection of the vehicle (following a collision).
  1. A pressure test point valve (schrader valve) is located on the fuel rail. This is used to measure fuel injector supply pressure for diagnostic procedures and repairs. ON VEHICLES NOT EQUIPPED WITH A SCHRADER VALVE, USE ROTUNDA FUEL PRESSURE TEST KIT #134—R0087 OR EQUIVALENT.
  1. Located on the fuel rail is a pulse damper. The pulse damper reduces fuel system noise caused by the pulsing of the fuel injectors. The vacuum port located on the damper is connected to manifold vacuum to avoid fuel spillage in the event the pulse damper diaphragm were to rupture (the pulse damper should not be confused with a fuel pressure regulator).
  1. The fuel injector is a solenoid-operated valve that meters the fuel flow to each combustion cylinder. The fuel injector is opened and closed a constant number of times per crankshaft revolution. The amount of fuel is controlled by the length of time the fuel injector is held open. The injector is normally closed and is operated by 12 volt VPWR from the power relay. The ground signal is controlled by the PCM.
  1. There are three filtering or screening devices in the fuel delivery system. The intake sock is a fine, nylon mesh screen mounted on the intake side of the fuel pump. There is a fuel filter screen located at the fuel rail side of the fuel injector. The fuel filter assembly is located between the fuel pump and the pressure test point/schrader valve.
  1. The fuel pump (FP) module contains the fuel pump, fuel pressure regulator and the fuel sender assembly. The fuel pressure regulator is attached to the fuel pump in the fuel pump module located in the fuel tank. It regulates fuel pressure supplied to the fuel injectors. The fuel pressure regulator is a diaphragm-operated relief valve. Fuel pressure is established by a spring preload applied to the diaphragm. Excess fuel is bypassed through the regulator and returned to the fuel tank.

    v22~us~en~file=aa1837a.gif~gen~ref.gif

    Figure 62: Fuel System—Mechanical Returnless
Electronic Returnless Fuel System The fuel system consists of a fuel tank with reservoir, fuel pump, fuel rail pressure sensor, fuel filter, fuel supply line, engine fuel temperature sensor, fuel rail, fuel injectors, and schrader/pressure test point. Operation of the system is as follows (Figure 63) and (Figure 64):
  1. The fuel delivery system is enabled during crank or running mode once the PCM receives a crankshaft position (CKP) sensor signal.
  1. The fuel pump logic is defined in the fuel system control strategy and is executed by the PCM.
  1. The PCM commands a duty cycle to the fuel pump driver module (FPDM).
  1. The fuel pump driver module modulates the voltage to the fuel pump (FP) to achieve the proper fuel pressure. Voltage for the fuel pump is supplied by the power relay or FPDM power supply relay. (For additional information on FPDM operation, refer to PCM Outputs—Fuel Pump and PCM Inputs—FPM.)
  1. The fuel rail pressure (FRP) sensor provides the PCM with the current fuel rail pressure. The PCM uses this information to vary the duty cycle output to the FPDM to compensate for varying loads.
  1. The engine fuel temperature (EFT) sensor measures current fuel temperatures in the fuel rail. This information is used to vary the fuel pressure and avoid fuel system vaporization.
  1. The fuel injector is a solenoid-operated valve that meters the fuel flow to each combustion cylinder. The fuel injector is opened and closed a constant number of times per crankshaft revolution. The amount of fuel is controlled by the length of time the fuel injector is held open. The injector is normally closed and is operated by 12 volt VPWR from the power relay. The ground signal is controlled by the PCM.
  1. A pressure test point valve (schrader valve) is located on the fuel rail. This is used to measure fuel injector supply pressure for diagnostic procedures and repairs. ON VEHICLES NOT EQUIPPED WITH A SCHRADER VALVE, USE ROTUNDA FUEL PRESSURE TEST KIT #134—R0087 OR EQUIVALENT.
  1. There are three filtering or screening devices in the fuel delivery system. The intake sock is a fine, nylon mesh screen mounted on the intake side of the fuel pump. There is a fuel filter screen located at the fuel rail side of the fuel injector. The fuel filter assembly is located between the fuel pump and the pressure test point/schrader valve.
  1. The fuel pump (FP) module is a device that contains the fuel pump and the fuel sender assembly. The fuel pump is located inside the reservoir and supplies fuel through the fuel pump module manifold to the engine and the fuel pump module jet pump.
  1. The inertia fuel shut-off (IFS) switch is used to de-energize the fuel delivery secondary circuit in the event of a collision. The IFS switch is a safety device that should only be reset after a thorough inspection of the vehicle (following a collision

Mar 21, 2009 | 2003 Ford Focus

2 Answers

Hard start when cold/first start in morning


The pressure relief valve is in the spider fuel injector not the fuel pump. We have had our 94 gmc jimmy for 4 years & have had to replace the fuel injector 4 times which cost right at $500 each time for the part. Yes the spider fuel injector cost averages around $500.

Nov 16, 2008 | 1994 GMC Jimmy

2 Answers

Cold start valve problem


if you have an electric cold start valve make sure to unplug it and if keeps apling fuel with electrical conector unpluged that means the valve is not good, but if not then you have an electronic problem, possible a bad cold start sensor or cold start module or cicuit problem, and might be a time to take it to an electrical shop

Jun 17, 2008 | 1987 Mercedes-Benz 300-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...