Question about Cars & Trucks

Open Question

Handbrake adjustment to vs holden ute

Vs holden ute handbrake needs adjustement

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: Handbrake Adjustment

On the Toyota, you can do it two ways: The easiest is to push in on the release button on the lever and move the lever up and down twenty or thirty times while the vehicle is slowly moving forward. A long driveway or parking lot is best for this. Or, there is an adjusting nut at the end of the park brake cable under the handle. If you pull the handle up, you should be able to see it down inside the center console on the bottom side of the handle. Turn the nut clockwise a turn or two.

The daewoo is anyone's guess. I've never even seen one.

Posted on Jul 14, 2008

Ad
  • 1 Answer

SOURCE: How to adjust the handbrake on a 2002 Daewoo Nubira

i think you'll have to look at the piece of felt under the casette holder lid , lift the felt up using a very fine flat ended screw driver and there should be a couple of bolts under there ! if yes , then take the lid off also , another two philips head screws . if its the same as the centre console of the 1998 model !! now , having removed the bolts , gently lift the rear end of the centre console , with a torch you should be able to see the adjuster . Make sure the hand brake is down , so put bricks under one or both of the front wheels and leave it in gear , also , do this on a flat surface !!!!
Adfter you've done the adjustment , before putting everything back together , put the console into normal position and try putting handbrake on and off , it should feel firm to lock the back brake  ! then if all is okay , put the screws back in reverse order good luck 

Posted on May 04, 2009

  • 1 Answer

SOURCE: hello , where is the handbrake adjuster on volvo v40 - 53reg

V40 cable ajuster is situated under the rear part of center console. Remove rear tray, undo the two posi screws, remove the cup holder rubber base cover to expose one more posi screw-undo.
Now you can lift the section backond off the handbrake lever.
Look under the flexi plastic cover and find a gold nut which has a sprung retainer.
You can now effect adjustment via this nut book suggests six to seven notches from off to on for ideal adjustment.

Posted on Sep 05, 2009

morse008
  • 1111 Answers

SOURCE: handbrake adjust

if you follow the cable there will be a turn buckle at some point turn it until the slack is correct it is most likely under the vehicle before the two cables meet usually halfway down the body or directly under the driver seat along the frame

Posted on Sep 07, 2009

  • 84 Answers

SOURCE: jaguar x type handbrake adjustment

car has 4 wheel disc brakes take off the rear pads and rotors u will see a set of shoes on the inside of that adjust thiem up and u should get alot more hand brake

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust hand brake on 2010 Holden Cruze after replacing pads


you don't, hand brake is not adjustable. If hand brake does not hold something else is at fault. Possible streched cable however it would not be unusual for the handbrake to be high but it should hold vehicle on a hill.

Jan 07, 2017 | Holden Cars & Trucks

1 Answer

How do i replace my hand brake cable on my ford falcon XH ute


wait a bit ....is it rear disc or rear drums on that ute

will assume its under dash hand brake pull lever tyoe

the disc setup may have single cables for each rear
rear disk brake cable is approx $ 150

if your XH it is close to the XE and XF set up drums
a complete one line loop cable outer and inner
with plastic grommets along the back chassis rail ( they break )
so the one inner cable works both rear handbrake shoes


hand brake cable is a shorty

undo the adjustment thread
just below the hand brake cable point up somewhere above the gearbox
(drums )
after new cable fitted
drums are adjusted with the old school way with the handbrake adjuster tool
handbrake cable adjusted

then the handbrake handle when pulled out to hold needs14 plus clicks
comes out a long way for some weird reason
on drums
if cable adjustment is done wrong onrear drums the handbrake cable will come loose in the drum as you drive along

26261095-l1jraapkfcyxqeqgczv0cruv-4-0.jpg

26261095-l1jraapkfcyxqeqgczv0cruv-4-3.jpg

26261095-l1jraapkfcyxqeqgczv0cruv-4-5.jpg

Aug 17, 2016 | Ford Cars & Trucks

1 Answer

HOW TO REMOVE A HAND BRAKE CABLE ON A WB HOLDEN UTE


find a holden hx hz wb manual or go to a library and photo copy the pages needed or look at the link below if you can do it on your own.
Replacing handbrake cable

May 05, 2016 | 1973 Holden Ute

2 Answers

Rubbing noise from back wheels


Silencer hanging down, brakes binding, tyres side ballooning inside edge, no oil in Differential.

Nov 22, 2014 | 1998 Holden VT Commodore

1 Answer

How do I get handbrake adjustment of 2002 3.2 Holden Vectra?


Hi there, try driving in reverse then pull the handbrake it should self adjust, good luck, not to fast just as tho as you are reversing into a car park

Oct 24, 2014 | Cars & Trucks

1 Answer

When handbrake is off,it beeps 3x,when you start to move, then it stops,plus the rear brakes stay on. why?


could be a few things. cable adjusted to tight, handbrake inner cables binding on outer cable and not releasing fully .

Sep 21, 2014 | Holden VT Cars & Trucks

1 Answer

Handbrake doesn't hold


handbrake wont hold due to incorrect adjustment method .
Under handbrake lever cover there is a thread rod with a 10mm nut on it undo it until the nut is level the top of the rod.
2.remove rear wheels
3.remove brake capliers and brackets
4.remove rear disc rotors.
5.get some sand paper and clean handbrake shoes and inside of disc rotors.
6.use a and adjusting tool and adjust the handbrake mechanism until you can feel drag on the rortor.
7.refit brake brackets and capliers
8.refit wheels
9.lower vehicle
10.now the vehicle is on the ground at the hbrake lever use a 10mm socket to adjust rod.
11.adjust the lever so its 7clicks .
12.on lever ground place the vehicle in drive apply hbrake 7clicks and it should hold vehicle..

Feb 26, 2014 | 1998 Holden VT Commodore

1 Answer

How do i tighten the handbrake on my mitsubishi triton ute 1994 4wd


Hi,
Inorder to tighten it you need to check to see if the side that is not holding if the primary shoe that the handbrake cable pulls on. If not then you may need to adjust the adjuster at the shoe. It may be too far retractor so when the handbrake is engaged, the shoe is not coming out far enough to grab the inside of the drum. There is most likely nothing wrong with the cable. You just need to adjust the shoes. When you pull the wheel off and inspect the shoes, you will see if they are not worn. To use the adjuster, pull see it will be near the retainer spring, the spring will connect from the top and bottom of the shoes to retract them. On the top side, where the upper spring is will be the mechanical adjuster, where you can adjust out the shoes to make them grab accordingly when engaged.

Let us know if you were looking for something more else please accept the suggestion.
Thank You for contacting Fixya.com

Feb 12, 2010 | Mitsubishi Pickup Cars & Trucks

1 Answer

Back wheel tight after changing brake pads,


adjustment needs to be backed of to the maximum,and if still draging sand the shoes

Oct 25, 2009 | 2007 Pontiac G8 Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...