Question about Cars & Trucks

Open Question

Fuel pump wireing diagram for 1988 chevy s10 - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Dumokie
  • 4 Answers

SOURCE: have a 1994 chevy s10

You need to check and make sure you have fuel pressure, then check for spark at ignition, if those check out then check for pulse width at the injectors. That basically is the electrical signal which tells injectors to spray fuel. Use what is called a Noid light on injector pulse width check. that will eliminate all possibilities other than internal issues with engine. I.E. broken cam, broken timing components, obviously if all I mentioned checks out then run compression test. Good Luck

Posted on Jul 15, 2008

Ad
fastboyz
  • 674 Answers

SOURCE: Engine Wire diagram for S10

i dont know of any free wiring diagrams but alldata.com is where the pros go to get ours

Posted on Sep 15, 2008

  • 1596 Answers

SOURCE: I need to replace the fuel pump in my 1985 Chevy S10 Pickup.

EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL

  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Posted on Mar 22, 2009

  • 52 Answers

SOURCE: fuel pump wiring diagram 1988 chevy truck

I personally have 1988 GMC truck and had to replace the fuel pump. I found all the info including wiring diagram in a haynes repair manual. These can be purchased in most automotive parts stores. Something I found interesting is that the fuel pump's operation works through the oil pressure switch, located by the distributor screwed into the engine block. If this switch is stuck or sticking it will affect the fuel pump. Replaced a good fuel pump for nothing! The truck had sit up for awhile and the ground wire connections had to be cleaned as well.

Posted on Sep 17, 2009

shop510
  • 90 Answers

SOURCE: s10 chevy pickup died, replaced fuel pump, still

Have you checked your ground wire to the pump?

Posted on Sep 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No fuel spray from injectos


1986 chevy s10 2.5l no gas coming from injector. - S-10 Forum

www.s10forum.com/.../1986-chevy-s10-2-5l-no-gas-coming-from-inject...
Sep 2, 2009 - 24 posts - ‎7 authors I have no gas coming from my injector it a 1986 chevy s10 2.5l I have replaced the fuel pump,oil pressure switch & I checked and oil would ...

Oct 12, 2015 | 1988 Chevrolet S-10

1 Answer

Where is the fuel filter located at on a 1988 chevy s10 extended cab 4.3 liter motor 4x4


Most fuel filters are now in the fuel tank with the pump. If I knew the year, make and model, I could tell you for sure.

May 06, 2015 | Cars & Trucks

1 Answer

What will shut the fire off from the fuel pump on a 1988 1 ton Chevy truck with 454 engine


Check battery side power & grounds ,
at the pump

Best if you work off wiring diagrams

Learn the fuel circuit first-- then do your testing

Oct 09, 2014 | Cars & Trucks

2 Answers

Fuel pump wiring diagram 1988 chevy truck


I personally have 1988 GMC truck and had to replace the fuel pump. I found all the info including wiring diagram in a haynes repair manual. These can be purchased in most automotive parts stores. Something I found interesting is that the fuel pump's operation works through the oil pressure switch, located by the distributor screwed into the engine block. If this switch is stuck or sticking it will affect the fuel pump. Replaced a good fuel pump for nothing! The truck had sit up for awhile and the ground wire connections had to be cleaned as well.

Sep 17, 2009 | 1988 Chevrolet C1500

1 Answer

Where is the fuel pump fuse on a 1989 chevy s10 pickup?


Fuses for the engine or exterior items are under the hood in a little black plastic box.

Fuses for the interior items are under the dash, up above the driver's left foot.

In either case, the fuse diagrams should be on the inside of the fuse cover.

Jun 09, 2009 | 1988 Chevrolet S-10

2 Answers

Engine Wire diagram for S10


i dont know of any free wiring diagrams but alldata.com is where the pros go to get ours

Sep 15, 2008 | 1988 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...