Question about Cars & Trucks

Open Question

How to replace oil pan on my 2000 ford 7.3 diesel

I was told I had to remove the motor to replace the oil pan some one else said they jacked the motor up and someone else said they took the transmission out which is rthe best way?

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Psych0Thrash
  • 53 Answers

SOURCE: 2000 7.3 Liter diesel engine needing oil pan replacement

sadly I don't think there is. The oil pan is huge and sections of the frame are in the way of getting it in and out without damaging the pan severly. pulling that massive engine and replacing the pan, then putting the engine back in and reconnecting everything in 14 hours is a good estimate. sorry for the bad news

Posted on Aug 18, 2008

Ad
  • 43 Answers

SOURCE: Transmission fluid/filter change in 2000 Honda Odyssey

I would not recommend using Dexron III. Honda Odysseys are prone to transmission problems. A drain and fill with Genuine Honda Fluid is Recommended. The drain plug can be removed with a 3/8 ratchet at the bottom of the trans. The fill hole is at the top of the trans. You remove it with a socket on a long extension. The capacity is close to 3 quarts

Posted on Apr 07, 2009

  • 4 Answers

SOURCE: how to remove the oil pan on a 2004 dodge ram 2500 diesel

I'd recommend getting a service manual first. I got one for my 2005 2500 cummins from www.promanuals.net. I also had to to remove the oil pan and replace it with another one.

Posted on Jun 20, 2009

  • 146 Answers

SOURCE: oil pan removal?

Im not sure if you are talking about the motor pan or the tranny pan. But I have lifted the motor and tranny together on a vehicle to change the motor pan and mounts before. I remember having to loosen the fan shroud. Undo linkage on the tranny and make sure the shifter boots were loose. The key for me was going real slow with the crane and having extra eyes around. It was a pain but it worked out.

Posted on Feb 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove an oil pan off a 1998 ford 2 wheel drive with out pulling the engine


Remove the bolt that runs thru the engines motor mounts, not the ones that attach it to the engine block. Take a 2x4 and put it on a floor jack so the jack won't damage the front pulley. Raise the engine with the floor jack to get enough clearance to manuver the pan around the steering components once thw oil pan bolts have been removed. Watch the fan blades don't hit the radiator.

Mar 09, 2015 | Ford Cars & Trucks

1 Answer

Ok I have a 1995 ford aspire im trying to figure out how to replace the oil pump


Disconnect the motor mounts and jack the engine to remove the oil pan. Remove the oil pan, replace the oil pump you'll find at the end of a pick up tube, replace the pump and put the pick up tube back on the new pump making sure it's in the same low position it was when removed, replace the oil pan gasket and put the oil pan back on, lower the engine and put the motor mount bolts back in. Put in the proper amount of oil and go.

Nov 13, 2014 | 1995 Ford Aspire

1 Answer

How to remove ford escort 1.8 diesal engine crank case and fitting details


FORD 2.0 MAZDA DIESEL ENGINE.YOU REMOVE CRANKCASE.FIRST DISCONNECT NEGATIVE BATTERY CABLE.RAISE AND SAFELY SUPPORT VECHICLE ON JACK STANDS.DRAIN THE ENGINE OIL.REMOVE THE BOLTS THAT ATTACH THE OIL PAN TO THE ENGINE AND REMOVE THE OIL PAN.CLEAN ALL GASKET MOUNTING SURFACE.APPLY A 1/8 INCH BEAD OF SILICONE SEALER ON THE OIL PAN MOUNTING SURFACE.INSTALL THE OIL PAN AND TIGHTEN THE BOLTS TO 5 - 7 FT LBS.

Oct 03, 2010 | 1998 Ford Escort

2 Answers

Replace Oil Pump Can it be doen without pulling


Yes it can. It can be replaced from the underside by removing the oil pan

May 03, 2010 | 1998 Ford Windstar

1 Answer

How difficult is replacing an engine pan and gasket on 95 ford f150 4.9 litre 2wd


  1. Drain the oil and the coolant
  1. Raise the vehicle on a lift. Disconnect the battery to starter relay cable at the starter motor and remove the bolts and starter motor.
  1. Remove the engine front support insulator-to-support bracket nuts and washers on both supports. Raise the front of the engine with a transmission jack and wood block and place thick wood blocks between the front mounts and engine. Lower the engine and remove the transmission jack.
  1. Remove the oil pan attaching bolts.
  1. Remove two bolts securing oil pump and screen bolts and drop them in the pan
  1. Remove oil pan

Mar 17, 2010 | 1995 Ford F150 Styleside Regular Cab

3 Answers

2000 Chevy Blazer


you have to remove motor mount bolts.... with engine hoist lift engine to get clearance to remove oil pan......you have to remove starter... trans cover ....... sounds like a easy job its not....hopethis helps

Dec 11, 2008 | 2000 Chevrolet Blazer

1 Answer

1994 oilpan


Remove the starter, remove the flywheel dust shield, remove the motor mounts center bolt, jack the engine as far up as possiable, this will then give you access to the oil pan bolts.

Oct 14, 2008 | 1994 Ford F350 Crew Cab

1 Answer

Oil pan removal problems on my 89 F-350 w/7.3L Diesel


remove the cross member then you can drop the pan

Sep 24, 2008 | 1989 Ford F 350

1 Answer

2000 7.3 Liter diesel engine needing oil pan replacement


sadly I don't think there is. The oil pan is huge and sections of the frame are in the way of getting it in and out without damaging the pan severly. pulling that massive engine and replacing the pan, then putting the engine back in and reconnecting everything in 14 hours is a good estimate. sorry for the bad news

Aug 18, 2008 | 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

Trying to drop the oil pan out of my 1994 Ford F-150 (4.9L) to replace the gasket. Ive taken out the motor mounts and jacked the engine almost high enough to get the oil pan out and I am wondering if i...


done this on several i-6 f-150s. slide back or remove transmission, remove motor mount bolts from frame(not motor), jack motor up as far as possible without damaging egr valve or wiper motor when they hit, shim under motor mounts so that when you drop the jack the motor does not come back down any(the motor is well balanced on the mounts, it will not fall out of the truck like a v8 will), then remove the oil pan. you May have to remove the pickup tube(usually not), and you May have to rotate the crankshaft so that the lobes clear the oil pan. this is a common problem with these trucks due to the size of the oil pan(Huge), and the minimum pan to crossmember clearance

Jul 19, 2008 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...